Motorola AP-0622 Manual de usuario

AP-0622 Access Point

INSTALLATION GUIDE

2AP-0622 Access Point

MOTOROLA SOLUTIONS and the Stylized M Logo are registered in the US Patent & Trademark Office. © Motorola Solutions,

Installation Guide 3

1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.1 Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.2 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.3 Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.4 AP-0622 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.0 Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.1 Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.2 Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.3 Access Point Placement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.4 Integrated Antenna Model Wall Mount Instructions . . . . . . . . . . . 8

2.5 Integrated Antenna Model Suspended Ceiling T-Bar Mount . . . . 11

2.6 External Antenna Model Wall Mount Instructions . . . . . . . . . . . . 12

2.7 External Antenna Model Suspended Ceiling T-Bar Mount . . . . . . 15

2.8 External Antenna Suspended Ceiling Tile (Plenum) Mount. . . . . . 17

2.9 AP-0622 External Antenna Model Antenna Options . . . . . . . . . . . 19

2.10 LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

3.0 Initial Access Point Configuration . . . . . . . . . . . . . . . . . . . . . 22

4.0 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

4.1 AP-0622 Integrated Antenna Model Electrical Characteristics. . . 23

4.2 AP-0622 Integrated Antenna Model Physical Characteristics . . . 23

4.3 AP-0622 External Antenna Model Electrical Characteristics . . . . 24

4.4 AP-0622 External Antenna Model Physical Characteristics . . . . . 24

4.5 Radio Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

5.0 Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

6.0 Part Numbers, Support, and Sales . . . . . . . . . . . . . . . . . . . . . 34

7.0 Motorola Solutions, Inc. End-User License Agreement . . . 35

8.0 AP-0622 Access Point China ROHS Compliance . . . . . . . . . 38

4AP-0622 Access Point

1 Introduction

The AP-0622 access point, a component of the Motorola Solutions wireless controller system, links wireless

802.11a/b/g/n devices to the controller, enabling the growth of your wireless network with a cost effective

alternative to standard access points. The AP-0622 access point provides multiple deployment options.

The AP-0622 access point receives all power and transfers data through the same CAT-5 or better Ethernet cable.

An 802.3af Ethernet switch or power supply (specifically rated for the AP-0622) is required (Part No.

PWRS-14000-148R).

This guide applies to Model Number AP-0622.

This document is written for the qualified network device installer.

1.1 Document Conventions

The following graphical alerts are used in this document to indicate notable situations:

NOTE Tips, hints, or special requirements that you should take note of.

CAUTION Care is required. Disregarding a caution can result in data loss or

equipment malfunction.

WARNING! Indicates a condition or procedure that could result in personal injury or

equipment damage.

Installation Guide 5

1.2 Warnings

• Read all installation instructions and site survey reports, and verify correct equipment installation before

connecting the AP-0622 model access point.

• Remove jewelry and watches before installing this equipment.

• Verify the unit is grounded before connecting it to the power source.

• Verify any device connected to this unit is properly wired and grounded.

• Verify there is adequate ventilation around the device, and that ambient temperatures meet equipment

operation specifications.

1.3 Site Preparation

• Consult your site survey and network analysis reports to determine specific equipment placement, power

drops, and so on.

• Assign installation responsibility to the appropriate personnel.

• Identify and document where all installed components are located.

• Ensure adequate, dust-free ventilation to all installed equipment.

• Identify and prepare Ethernet and console port connections.

• Verify cable lengths are within the maximum allowable distances for optimal signal transmission.

1.4 AP-0622 Package Contents

An AP-0622 access point is available in integrated antenna and external antenna models. Contents differ

depending on the model ordered.

1.4.1 External Antenna Model Package Contents

• AP-0622 access point with external antenna connectors (Plenum Rated)

• 2 customer installed mounting lugs

• 4 mounting lug retaining screws

• AP-0622 Installation Guide (This Guide)

1.4.2 Internal Antenna Model Package Contents

• AP-0622 access point with internal antennas

• AP-0622 Installation Guide (This Guide)

6AP-0622 Access Point

1.4.3 Features

• 2 RJ-45 connectors, one for 10/100/1000 Ethernet and the other for the serial/console connector

• LED indicators

• Slots for wall mounting

• Clips for mounting on a suspended ceiling T-bar (internal antenna model only) with separately orderable

accessories

• Lock port for Kensington style Security Lock

The AP-0622 access point has one RJ-45 connector supporting an 10/100/1000 Ethernet port and accepts

802.3af-compliant power from an external source. The illustration below is of an integrated antenna model

AP-0622.

The AP-0622 access point comes with dual radios supporting 802.11a/b/g/n. The access point contains runtime

firmware which enables the unit to boot after a power up or watchdog reset. The runtime firmware on the access

point and the firmware downloaded from the connected controller can be updated via the Ethernet interface.

NOTE When operating in a Gigabit Ethernet environment, CAT-5e or CAT-6 cable

is recommended for Gigabit operation.

DC12V GE1/PoE Console

Installation Guide 7

2 Hardware Installation

2.1 Installation Instructions

The AP-0622 access point mounts either on a wall (with customer supplied M4 x 25 pan head screws and wall

anchor - or equivalent) or on a suspended ceiling T-bar. If deploying an external antenna model AP622, access point

mounting kit (Part No. KT-135628-01) is required. An AP-0622 is not designed for mounting on a desk.

To prepare for the installation:

1. Match the model number on the purchase order with the model numbers in the packing list and on the case of

the access point.

2. Verify the contents of the box include the intended AP-0622 access point, and he included hardware matches

the package contents on page 4.

3. Review site survey and network analysis reports to determine the location and mounting position for the

AP-0622 access point.

4. Connect a CAT-5 or better Ethernet cable to a compatible 802.3af power source and run the cable to the

installation site. Ensure there is sufficient slack on the cable to perform the installation steps.

2.2 Precautions

Before installing an AP-0622 model Access Point, verify the following:

• Your using the correctly rated power supply for the AP-0622 (PWRS-14000-148R)

• Motorola Solutions recommends you do not to install the AP-0622 in wet or dusty areas.

• Verify the environment has a continuous temperature range between 0° C to 40° C.

Part Number Description

AP-0622-66030-US 802.11n dependent access point, dual radio, internal antenna

AP-0622-66040-US 802.11n dependent access point, dual radio, external antenna

AP-0622-66030-WR 802.11n dependent access point, dual radio, internal antenna

AP-0622-66040-WR 802.11n dependent access point, dual radio, external antenna

NOTE In the above part numbers, acountry code of “WR” represents a world

wide model, whereas “US” defines the model as only legally deployable

in the United States.

NOTE When operating in a Gigabit Ethernet environment, CAT-5e or CAT-6 cable

is recommended for Gigabit operation.

8AP-0622 Access Point

2.3 Access Point Placement

For optimal performance, install the access point away from transformers, heavy-duty motors, fluorescent lights,

microwave ovens, refrigerators and other industrial equipment. Signal loss can occur when metal, concrete, walls

or floors block transmission. Install the access point in an open area or add access points as needed to improve

coverage.

Antenna coverage is analogous to lighting. Users might find an area lit from far away to be not bright enough. An

area lit sharply might minimize coverage and create dark areas. Uniform antenna placement in an area (like even

placement of a light bulb) provides even, efficient coverage.

Place the access point using the following guidelines:

• Install the access point at an ideal height of 10 feet from the ground.

• Orient the access point antennas vertically for best reception (applies to external antenna models only).

To maximize the access point’s radio coverage area, Motorola Solutions recommends conducting a site survey to

define and document radio interference obstacles before installing the access point.

2.4 Integrated Antenna Model Wall Mount Instructions

This mounting requires hanging the AP-0622 along its width or length using the two slots on the bottom of the unit.

The AP22 can be mounted onto any plaster, wood, or cement wall surface using customer supplied screw hardware

(M3.5 x 0.6 x 20 mm- or equivalent).

2.4.1 Wall Mount Hardware

• Two wide-shoulder Phillips pan head self-tapping screws (customer supplied)

• Two wall anchors (customer supplied)

• Security cable (optional)

NOTE The following screws are recommended: (ANSI Standard) #6-18 X

0.875in. Type A or AB Self-Tapping Screw, or (ANSI Standard Metric)

M3.5 X 0.6 X 20mm Type D Self-Tapping Screw.

Installation Guide 9

2.4.2 Wall Mount Procedure

1. Orient the case on the wall by its width or length.

CAUTION To ensure proper operation of an AP-0622 access point, ensure it is

mounted in the correct orientation as shown above.

10 AP-0622 Access Point

2. Mark two points (for drill holes) 4.08 inches (103 .7 mm) apart on a horizontal line.

3. At each point, drill a hole in the wall, insert an anchor, screw into the anchor the wall mounting screw and stop

when there is 1mm between the screw head and the wall .

4. If required, install and attach a Kennsington security cable (customer supplied) to the unit’s lock port.

5. Attach an Ethernet cable from the access point to a controller with an 802.3af-compatible power source or use

the PWRS-14000-148R power supply to supply power to the AP-0622 (once fully cabled).

6. Place the middle of each of the case’s mount slots over the screw heads.

7. Slide the case down along the mounting surface to hang the mount slots on the screw heads.

8. Verify the unit has power by observing that the LEDs are lit or flashing.

NOTE When pre-drilling a hole the recommended hole size is 2.8mm (0.11in.).

CAUTION If not using a 802.3af capable controller to power the AP-0622, ensure

only the AP-0622’s designated power supply (PWRS-14000-148R) is

used to supply power to the access point. Using an incorrectly rated

power supply could damage the unit and void the product warranty.

Do not actually connect to the power source until the cabling portion

of the installation is complete.

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de Motorola

Motorola

Motorola AP6562 Manual de usuario

Motorola

Motorola PMP 100 Manual de instrucciones

Motorola

Motorola 5440AP - Canopy 5.4 GHz AP Manual del propietario

Motorola

Motorola AP-5181 - Wireless Access Point Guía de referencia rápida

Motorola

Motorola AP-6521 Series Manual de usuario

Motorola

Motorola AP-621 Series Manual de usuario

Motorola

Motorola Canopy 300 Mbps Backhaul Manual de usuario

Motorola

Motorola AP 7181 Manual de usuario

Motorola

Motorola AP-650 Series Manual de usuario

Motorola

Motorola TLN3221B Manual de usuario

Motorola

Motorola CB3000 - Client Bridge - Wireless Access... Manual de usuario

Motorola

Motorola Solutions WiNG 5.2.6 Manual de usuario

Motorola

Motorola MOTOMESH Duo 4300-49 Manual de usuario

Motorola

Motorola WA840G Instrucciones de funcionamiento

Motorola

Motorola AP-6511 Manual de usuario

Motorola

Motorola AP-6511 Manual de usuario

Motorola

Motorola AP-51 Series Manual de instalación y operación

Motorola

Motorola AP-7532 Manual de usuario

Motorola

Motorola WiNG 5 Manual de usuario

Motorola

Motorola AP 7161 Manual de usuario

Motorola

Motorola AP-7131N-FGR Manual de instalación y operación

Motorola

Motorola AP6522 Manual de usuario

Motorola

Motorola AP-650 Series Manual de usuario

Motorola

Motorola AP6562 Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Cisco

Cisco Aironet 1550 Series Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario