Motorola AP-5181 - Wireless Access Point Guía de referencia rápida
AP-5181
Access Point
DEPLOYMENT GUIDE
2AP5181 Access Point
MOTOROLA SOLUTIONS and the Stylized M Logo are registered in the US Patent & Trademark Office. © Motorola Solutions,
Inc. 2011. All rights reserved.
Service Information
If you have a problem with your equipment, contact support for your region. Support and issue resolution is provided for
products under warranty or are covered by an agreement. Contact information and web self-service is available by visiting
http://supportcentral.motorola.com/.
When contacting support, please provide the following information:
• Serial number of the unit
• Model number or product name
• Software type and version number
Motorola Solutions responds to calls by email or telephone within the time limits set forth in support agreements. If you
purchased your Enterprise Mobility business product from a Motorola business partner, contact that business partner for
support.
Support Web Site
The Support Central Web site, located at http://supportcentral.motorola.com/ provides information and online assistance
including developer tools, software downloads, product manuals, support contact information and online repair requests.
Deployment Guide 3
Introduction
This guide provides detailed hardware setup and deployment instructions for the AP-5181 model access point.
The AP-5181 model access point is primarily designed for outdoor deployments, thus it has a unique set of
installation instructions.
Please review all the material within this document before installing the AP-5181 model access point. The
purpose of this guide is to assist you in understanding the correct use and placement of the components within
the AP-5181 accessory kits. Proper installation is critical to the safety of the installation, installer and others in
the area of the AP-5181’s deployment.
Mounting Kit and Assembly
It is recommended the assembly of the AP-5181’s accessories be started, and fully staged (as described in this
chapter) before the AP-5181 is moved into its final area of deployment.
Installing the AP-5181’s Mounting Accessories
To install the AP-5181’s mounting accessories:
1. Install the mounting bracket to the AP-5181’s rear housing using 4 short length binder head screws from
the kit. Tighten securely.
NOTE Take note of the earth ground boss under the bracket. This point must be properly
grounded to earth to utilize this products safety features. This is a good time to add the
required grounding lug or cable (not included with the AP-5181 or mounting kit).
4AP5181 Access Point
2. Install the AP-5181 tilt bracket onto the AP-5181’s bracket installed in step 1.
Use one long binder head screw and hex nut from the kit. This will define the pivot about which the
AP-5181 can be tilted. Do not over tighten the nut.
3. Install 4 short binder head screws in the 4 slots, 2 each on left and right sides of the tilt bracket.
These can be tightened during this phase of the assembly. Once deployed in the field, the 4 screws should
be loosened slightly to allow the AP-5181 to be tilted to level, then re-tightened.
Deployment Guide 5
4. If sliding to a small pole diameter, up to 2 ½ inches in diameter, place the pole clamps into the slots of the
bracket assembled in step 3.
The pole clamps can be installed into inner or outer slots to adjust for pole diameters of various sizes.
5. Install 2 long binder head screws through the two holes of one clamp into the other clamp. Direction is
not important.
6AP5181 Access Point
On each long screw, install one split washer and one wing nut. Leave them somewhat loose, as the nut,
washer and screw will be loosened and re-installed in the field when mounting the AP-5181 to a Pole.
Installing the AP-5181 on a Pole
To install an AP-5181 on a pole:
1. Select the proper slot positions for the pole clamp to properly fit onto the pole. Position and hold the tilt
bracket. Align each of the 2 pole clamps in position on the pole. Install 2 long binder head screws through
the two holes of one clamp and into the other clamp. Direction is not important.
Install one split washer and one wing nut onto each long screw. Lightly tighten the wing nut, washer and
screw.
Point the tilt bracket in the direction the AP-5181 is to be mounted, and tighten the wing nut, washer and
screw
NOTE The unit is ready to be moved into its deployment area and mounted onto a pole (where
the AP-5181 cannot be slid over the pole end).
Deployment Guide 7
2. Install the mounting bracket onto the tilt bracket installed in step 1. Use one long binder head screw and
hex nut from the kit. This will provide the pivot about which the AP-5181 can be tilted. Do not over tighten
the nut.
3. Install 4 short binder head screws in the 4 slots (two each on left and right sides of the tilt bracket). Set
the angle of the AP-5181 up or down as required for the installation. The 4 short binder head screws and
the long screw hex nut can all be tightened to lock the unit into position.
8AP5181 Access Point
The image displayed above has the heavy weather accessory kit installed. Whether the unit is installed
with the heavy weather kit, or without it, it will be important to connect the
AP-5181 to an appropriate earth ground using the earth-ground boss on the back of the unit.
4. Thread the 2 band clamps through the adapter.
Using both band clamps, position the adjuster screw about 6 inches from the face of the adapter. The
adjuster screw can be installed to either left or right sides.
5. Mount the adapter to the tilt bracket using 2 short binder head screws. It does not matter which side is
up or down, left or right. Tighten the screws securely.
NOTE It is necessary to use the band clamp adapter when installing an AP-5181 on a larger
diameter pole (up to 18 inches).
Deployment Guide 9
6. Position and hold the tilt bracket and each of the band clamps onto the mounting pole. Thread the band
clamp through its own adjuster screw. Ensure the band clamp is installed into it’s own adjust screw.
Thread the free end of the band clamp through the adjuster. Pass through the screw, and pull the free end
of the clamp until it is snug. Repeat this process for the second clamp.
Point the tilt bracket in the direction the AP-5181 is to be mounted. Tighten the band clamps. Cut-off or
wrap around (as displayed above) the free end of the tightened band clamp.
7. Install the AP-5181’s mounting bracket onto the tilt bracket. Use one long binder head screw and hex nut
from the kit. This will provide the pivot about which the AP-5181 can be tilted. Do not over tighten the nut.
10 AP5181 Access Point
The image displayed has the heavy weather accessory kit installed. Whether the unit uses the heavy
weather kit or not, remember to connect the AP-5181 to an appropriate earth ground using the
earth-ground boss on the back of the unit.
8. Install 4 short binder head screws in the 4 slots (2 each on left and right sides of the tilt bracket). Set the
angle of the AP-5181 up or down as required for the installation. The 4 short binder head screws, and the
long screw hex nut can be tightened to lock the AP-5181into position.
Otros manuales para AP-5181 - Wireless Access Point
1
Tabla de contenidos
Otros manuales de Punto de acceso inalámbrico de Motorola
Motorola
Motorola AP 6522M Manual de usuario
Motorola
Motorola PMP 320 Manual de usuario
Motorola
Motorola AP-621 Series Manual de usuario
Motorola
Motorola MotoWI4 PTP 600 Series Manual de usuario
Motorola
Motorola AP-51 Series Manual de instalación y operación
Motorola
Motorola CB3000 - Client Bridge - Wireless Access... Manual de usuario
Motorola
Motorola NCAP-500 Series Manual de usuario
Motorola
Motorola PTP 600 Series Manual de usuario
Motorola
Motorola AP-6521E Manual de usuario
Motorola
Motorola WiNG 5.7.1 Manual de usuario
Motorola
Motorola AP-8132 Manual de usuario
Motorola
Motorola CB3000 - Client Bridge - Wireless Access... Manual de usuario
Motorola
Motorola AP 7181 Manual de usuario
Motorola
Motorola PMP 320 Manual de usuario
Motorola
Motorola AP6522E Manual de usuario
Motorola
Motorola P-7131N-FGR Manual de instalación y operación
Motorola
Motorola AP-650 Series Manual de usuario
Motorola
Motorola AP-650 Series Manual de usuario
Motorola
Motorola WA840G Manual de usuario
Motorola
Motorola AP6562E Manual de usuario
