Motogadget Mo.switch basic Manual de usuario

instruction manual

mo.switch basic

V1.0

Thank you very mutch for pruchasing a high quality motogadget product - Made in Germany.

THIS PRODUCT CAN HANDLE CURRENTS OF MAX. 0,1A AND IS NOT

SUITABLE TO SWITCH LOADS DIRECTLY. LOADS MUST BE SWIT-

CHED BY A ELECTRONIC SWITCHING MODULE (i.e. MO.UNIT).

Please read the following information and recommendations thoroughly and follow these in-

structions during installations and use of the product. No liability shall be assumde by mo-

togadget for damage or defects resulting from negligence or failure to follow the operating and

installation guide.

Contact:

motogadget GmbH

Köpenicker Str. 145

D - 10997 Berlin

Germany

Tel. +49 (0)30-6900410-0

www.motogadget.de

[email protected]

motogadget are registrated trademarks of

motogadget GmbH, Berlin, Germany.

1. Review of Delivery

All products from motogadget are thoroughly checked to ensure they are completely fault-free

when dispatched. Please check the received goods immediately for possible transport dama-

ge. If you  nd any damage or other de ciencies, please contact us immediately.

In this regard, we refer to our General Terms of Business and Delivery, which are published

at www.motogadget.com. Should a return of the received delivery be agreed, please note that

we only take back goods in their original packaging. The mo.switch and its accessories must be

returned within the legal period of time and without any traces of use. We shall not assume any

liability for returns which are insufciently insured or packed.

2. Exclusion of Liability

THE DEVICE AND ITS ACCESSORIES MUST BE INSTALLED BY A CERTIFIED MO-

TORCYCLE TECHNICAN AND IN AN AUTHORIZED SERVICE CENTER. MOTOGADGET

ACCEPTS NO LIABILITY FOR DIRECT OR INDIRECT DAMAGE OR SUBSEQUENT DA-

MAGE OF ANY KIND RESULTING FROM THE USE, INSTALLATION OR CONNECTION

OF THE DEVICE OR OTHER DELIVERED EQUIPMENT. THIS EXCLUSION OF LIABILITY

PARTICULARLY INCLUDES DAMAGE TO PERSONS, MATERIAL LOSSES AND FINAN-

CIAL DAMAGES. THE USE IN AREAS OF PUBLIC TRAFFIC ENSUES AT THE USER’S

OWN RISK. THE USE OF THE DELIVERED DEVICE AND ITS ACCESSORIES FOR RA-

CING OR OTHER COMPETITIONS AS WELL AS FOR ANY USE NOT CORRESPONDING

TO THE RECOMMENDED APPLICATION ALL WARRANTY CLAIMS SHALL BE INVALID.

3. Safety Instructions

• THE VEHICLE BATTERY MUST BE COMPLETELY DISCONNECTED PRIOR TO ANY

WORK ON THE VEHICLE’S ELECTRICAL SYSTEM. FIRST, DISCONNECT THE NEGA-

TIVE TERMINAL AND THEN THE POSITIVE TERMINAL. FOR RECONNECTION

PROCEED IN THE REVERSE ORDER

• USING THE MO.SWITCH WITH PLUS POLE CONNECTED TO VEHICLE FRAME (OLDER

ENGLISH MOTORCYCLES) IS NOT POSSIBLE.

• INSTALLATION AND ELECTRICAL CONNECTION OF THE MO.UNIT MAY ONLY BE

CARRIED OUT BY A CERTIFIED MOTORCYCLE TECHNICIAN.

• ALL CABLE DIAMETERS MUST BE DIMENSIONED ACCORDING TO THE CURRENT

FLOW

• ALL ELECTRICAL CONNECTIONS IN THE WIRING LOOM AND AT THE CONNECTION

TERMINALS HAVE TO BE CARRIED OUT PROFESSIONALLY. FAILURES AT CONNECT-

ING JOINTS MAY CAUSE A CONTACT RESISTANCE AND LEAD TO HEAT GENERATION

DURING HIGH CURRENT FLOW. THERE IS A RISK OF SERIOUS OR LETHAL INJURIES.

4. mo.switch combinations

4 push buttons - kickstarter & no instrument

5 push buttons - kickstarter & instrument or E-starter & no instrument

6 push buttons - E-starter & instrument

horn

turn left

lights

turn right

horn

turn left / right

light

starter or instrument

horn

turn left / right

light

starter / instrument

5. Setup

push buttons push button plate

ground terminal

screw ringlet chopper disc

tapered screw for

ground connetion

xing screw

button plate

housing

clamping screw

adapter sleve

22mm to 1inch

housing

Mount all handlebar attachments

and nalize their position.

Clamp mo.switch housing to handlebar.

Drill 4 holes with 5mm diameter into the

handlebar. Deburr the holes inside and

outside carefully.

6. Wiring

7. Wiring

7.1 Ground connection to handlebar

With an ohmmeter, the resistance between battery negative pole and the handlebar surface is

measured. If the resistance is higher than 3 ohms, a separate ground wire must be routed from the

negative battery terminal to one of the mo.switch housing ground points.

Handlebars that are not made of metal, e.g. Carbon, need a separate ground wire from the battery

negative terminal to each of the mo.switch housing ground points.

When tightening the M3 grub screw into the mo.switch housing, the tip of the screw penetrates the

handlebar surface and thus creates a secure ground connection between the handlebar and the

housing.

The further ground connection for the pushbuttons is then carried out with the grounding cables

supplied; connected at the mo.switch ground point with the M3 screw and the eyelet. In the pro-

cess the supplied chopper disc is placed between the eyelet and the housing.

The free ends of the grounding cables are connected to a terminal contact of each button. The

polarity does not matter.

All further ground connections, e.g. for the indicators and brake switch also carried out by using a

mo.switch housing ground point.

7.2 Standard wiring

horn lights

brake switch

turn left turn right starter instrument menue

turn signal left

(optional)

turn signal right

(optional)

ground wire

(optional) 9 pol. motogadget wire

article no. 9003061

red

ground point

purple

blue

brown

to right

ground point

to left

ground point

to right

ground point

black orange

yellow

green

from battery minus

to left ground point

ground point

red mo.unit input HORN

purple mo.unit input TURNL

white mo.unit input TURN R

brown mo.unit input BRAKE

blue mo.unit input LIGHT

yellow mo.unit input START

green instrument menue

black mo.unit output TURN L

orange mo.unit output TURN R

white

7.3 Wiring with mo.button

horn lights

brake switch

turn left turn right starter instrument menue

(optional)

ground wire

(optional)

mo.button - green

to mo.unit input KILL

from battery minus

to right ground point

ground point ground point

red

yellow white

orange

blue

purple

mo.button - black

to left ground point

mo.button

Tabla de contenidos

Otros manuales de Accesorios para motocicletas de motogadget

motogadget

motogadget Motoscope Tiny Manual de usuario

motogadget

motogadget motoscope Classic Manual de usuario

motogadget

motogadget motoscope mini Manual de usuario

motogadget

motogadget m-Unit V.2 Manual de usuario

motogadget

motogadget mo.switch pro Manual de usuario

motogadget

motogadget mo.relay+ Manual de usuario

motogadget

motogadget mo.hub Manual de usuario

motogadget

motogadget motoscope pro Manual de usuario

motogadget

motogadget motoscope mini rally Manual de usuario

motogadget

motogadget mo.stop Manual de usuario

motogadget

motogadget Chronoclassic 2 Manual de usuario

Manuales populares de Accesorios para motocicletas de otras marcas

SRC

SRC B-TRK502-01-01-SL Manual de usuario

3M Speedglas 9100 MP Manual de usuario

hepco & becker

hepco & becker 6307520 00 01 Manual de usuario

HOMCOM

HOMCOM AA0-077 Manual de usuario

hepco & becker

hepco & becker 6307558 00 01 Manual de usuario

Wunderkind Custom

Wunderkind Custom 106503-F15 Guía del usuario

Dräger

Dräger HPS 3500 Manual de usuario

M-WAVE

M-WAVE SKI Manual de usuario

Kuryakyn

Kuryakyn 6212 Manual de usuario

hepco & becker

hepco & becker 6507504 00 01 Manual de usuario

Tool it

Tool it PROMAX LCD 9.13G Manual de usuario

Custom Dynamics

Custom Dynamics TruWrapz Manual de usuario

Roof

Roof RO200 CARBON Manual de usuario

Kabuto

Kabuto Japan IBUKI Manual de usuario

PUIG

PUIG 5051 Manual de usuario

rizoma

rizoma ZTH050 Manual de usuario

Joubert

Joubert 10001711 Manual de usuario

Sperian

Sperian Optrel p420 Manual de usuario

motogadget mo.switch basic Manual de usuario

Manuales populares de Accesorios para motocicletas de otras marcas