Morphy Richards Essentials Bag Vacuum Cleaner Manual de usuario

EEsssseennttiiaallssbbaaggggeeddvvaaccuuuummcclleeaanneerr

Please read and keep these instructions

Getting the best from your new cleaner...

If your cleaner is not picking up as well as it should, please check

DDuussttbbaagg

It is important to replace them when full, otherwise the

performance of the cleaner will be impaired.

FFiilltteerrss

It is important that filters are cleaned and replaced

regularly to allow air through the appliance.

BBlloocckkaaggeess

Check the hose, tubes and tools for blockages.

BBeelltt

Check and replace damaged or broken belt.

HHeeiigghhttaaddjjuussttmmeenntt

The height adjustment only comes into effect when the handle

is released by the handle release pedal Â.

SSaaffeettyyccuutt--oouutt

If the airflow is blocked or the filters are not regularly cleaned

a thermostat may operate. If this happens, switch off and disconnect

from the mains supply. Clear any blockages, replace dust bag

and clean filters. Allow 60 minutes for the thermostat to reset.

VC73342 MUK Rev 1

For replacement parts, help with using your Morphy Richards products,

problems and lots more, contact us by phone or through our website.

UK Helpline: 0870 060 2604

Replacement parts: 0870 167 6635

Ireland 1800 409119

73342 rev1 13/3/07 15:02 Page 1

IMPORTANT

SAFETY

INSTRUCTIONS

The use of any electrical

appliance requires the

following of common sense

safety rules.

Primarily there is danger of

personal injury and

secondly danger of

damage to the appliance

and property. These are

indicated in the instructions

text by the following two

conventions:

WARNING: Danger of

personal injury

IMPORTANT: Damage to

the appliance

In addition we offer the

following essential safety

advice.

Location

• Do not use or keep this

product outside in the rain.

• Do not store the appliance

near hot surfaces eg ovens

or heating appliances.

Mains lead

• Do not allow the mains

lead to become strained or

run this appliance over it.

• If the electrical cable

becomes damaged the

cable assembly must be

replaced. Do not attempt

this task yourself, contact

the helpline number that is

found at the bottom of the

page.

Personal safety

•WARNING: Keep loose

clothing, hair, fingers

etc. away from the floor

nozzle whenever the

cleaner is connected to

the mains.

• The plug must be removed

from the wall socket before

cleaning or maintaining the

appliance.

• Never modify the cleaner in

any way.

• Never use in the presence

of explosive liquids or

vapours.

• Never pick up inflammable

or poisonous liquids such

as petrol, copier toner or

other volatile substances.

Never pick up acids,

asbestos or asbestos dust.

• Repairs to electrical

appliances are only to be

undertaken by trained

personnel. Unprofessional

repairs can be dangerous

for users.

• Use only genuine Morphy

Richards spare parts and

accessories.

• The appliance must never

be left running when

unsupervised.

• This vacuum cleaner is

intended for domestic use

only. Misuse or use for

commercial or any other

purpose will render the

guarantee invalid.

• This appliance is not

intended for use by

persons (including children)

with reduced physical,

sensory or mental

capabilities, or lack of

experience and knowledge,

unless they have been

given supervision or

instruction concerning use

of the appliance by a

person responsible for their

safety.

Product safety

• Never use the appliance

without the bag or filters

being installed.

• Never use the appliance to

vacuum hot ashes, broken

glass, sharp objects or

liquids.

Children

• Children do not understand

the dangers associated

with operating electrical

appliances. Never allow

children to use this

appliance.

• Children should be

supervised to ensure that

they do not play with the

appliance.

ELECTRICAL

REQUIREMENTS

Check that the voltage on

the rating plate of your

appliance corresponds with

your house electricity

supply which must be A.C.

(Alternating Current).

If the socket outlets in your

home are not suitable for

the plug supplied with this

appliance the plug should

be removed and the

appropriate one fitted.

WARNING: The plug

removed from the mains

lead, if severed, must be

destroyed as a plug with

a bared flexible cord is

hazardous if engaged

into a live socket outlet.

Should the fuse in the 13

amp plug require changing

a 13 amp BS1362 fuse

must be fitted.

UUKKHHeellpplliinnee0088770000660022660044RReeppllaacceemmeennttPPaarrttss0088770011667766663355IIrreellaannddHHeellpplliinnee11880000440099111199

73342 rev1 13/3/07 15:02 Page 2

FEATURES

⁄Upper handle

¤Flexible hose

‹Main body

›Hose connector

ﬁCarpet height adjustment

knob

ﬂHepa filter grille

‡Front panel

·Full bag indicator

‚On/Off switch

„Front cover release handle

‰Floor nozzle with powered

brush

ÂHandle release

ÊCarrying handle

ÁCord storage with quick

release cleat

ËHose clip slot

ÈHose clip

ÍSafety bag interlock

(shown page 5)

ÎBelt cover (page 6)

ÏBrush bar (page 6)

ÌMotor shaft (page 6)

ÓBrush bar end cap (page 6)

Accessories you should

have

ÔFurniture brush

Crevice tool

ÒNested extension tubes x 2

ÚTurbo nozzle (certain

models only)

⁄

‹

›

ﬁ

ﬂ

‡

‚

‰

„

Ô

‚

73342 rev1 13/3/07 15:02 Page 3

44UUKKHHeellpplliinnee0088770000660022660044RReeppllaacceemmeennttPPaarrttss0088770011667766663355IIrreellaannddHHeellpplliinnee11880000440099111199

OPERATING THE

APPLIANCE

Assembly A

WARNING: Do not plug in

the cleaner until it is

assembled.

1Carefully unpack all

components.

2Lift cleaner body to upright

position.

3Remove the two screws that are

already attached to the body.

4From the rear of the cleaner,

align the handle with groove and

slide into the body. If necessary,

use thumb and finger pressure

to slide handle into position.

5Fasten the handle with the two

screws.

Floor nozzle height

adjustment B

Before using the cleaner the

floor nozzle height must be set

to the correct height.

Choose the setting which most

closely matches your floor

surface, ie. deep carpet pile,

medium carpet pile, short carpet

pile or hard floor.

IMPORTANT: When using the

attachments the cleaner must

only be used in an upright

position with the carpet height

adjustment knob set to tools

setting.

Note: The height adjustment

only comes into effect when the

handle is released by the handle

release pedal Â.

Using on carpets

1Place cleaner in its upright

position.

2Set the carpet height

adjustment knob to the desired

position.

3Release the mains cable by

revolving the quick release cleat

1/2 a turn and extend the cable

fully.

4Plug the cable into the mains

socket.

5Step on the handle release

pedal to release the handle to

the desired position.

6Press the on/off button to the 1

position.

IMPORTANT: To prevent damage

to carpets, never leave the

cleaner switched on in one

place for an extended period.

• Never have the brushes set too

low such that the cleaner is hard

to push.

Using attachments

Follow steps 1-4 above but set

the carpet height adjustment

knob to the tools setting.

5Remove the hose connector ›

from the rear of the cleaner. Lift

the hose ¤from the top handle

hook and push the required

attachment onto the end of the

hose.

• Push the required attachment

firmly onto the end of the hose.

• If additional length is required,

attach one or both extension

tubes between the hose and

tool.

73342 rev1 13/3/07 15:02 Page 4

6Switch on/off.

• IMPORTANT: Always fix the

hose clip Èto the main

body slot Ë when using the

hose and tools.

• Never over extend the hose

such that the cleaner is

pulled over.

• Turning the cleaner

sideways helps prevent the

cleaner being pulled along

by the stretch hose.

Turbo brush

(certain models only) Ú

This nozzle is suitable for

cleaning and rejuvenating cut

pile stair carpets and upholstery.

It is ideal for picking up

stubborn dirt and pet hairs.

Cleaning the turbo

nozzle (certain models only)

The turbo nozzle should be

regularly cleaned and any hairs

or fibres wrapped around the

brush bar removed to maintain

optimum performance.

DUST CANISTER

Dust bag indicator

When the cleaner is switched

on, if the dust bag condition

indicator is continuously

showing red (or if the suction is

reduced) the bag must be

replaced and the filters cleaned.

If it is still showing red after

emptying the dust bag and

cleaning the filters, check to see

if the hose is blocked.

Changing the dust

bag C

1Unplug the power cable from

the socket.

2Remove the front by pressing

the release lever at the top.

3Remove the old dustbag by

holding the cardboard tab and

pull towards you. Remove

carefully to avoid dust/dirt

spilling from the dust bag and

dispose.

4Take a new dust bag and fold

over the top tab at the crease.

Holding the cardboard tab, push

the bag over the opening of the

dirt discharge tube until it is

seated against the rear of the

enclosure.

5IMPORTANT: The front panel will

not close unless the dust bag is

correctly fitted due to the safety

bag interlock. The interlock

prevents the cover closing

unless a bag is fitted.

6Once the new dust bag is in

place, replace the front panel by

aligning the bottom locking tabs

with the slots in the body, close

cover slowly allowing the front

panel to snap in place. The latch

will self lock.

Cleaning the pre-

motor filter D

Everytime a new bag is fitted,

the filter should be taken out

and cleaned. Failure to clean the

filter will reduce suction and will

damage the motor if used for

prolonged periods. This may

invalidate the guarantee. If the

filter becomes damaged it must

be replaced.

IMPORTANT: Do not operate the

cleaner without the filter in

place.

1Remove the front cover of the

cleaner. The pre-motor filter is

located below the bag.

2To remove the filter, slide the

holder out of the machine.

3Remove the filter from the

holder by unclipping. To clean

shake vigorously over a dustbin.

• The pre-motor filter may also be

washed in warm water.

• Do not use detergents. The filter

must be completely dry before

refitting. Allow the filter to dry

naturally, do not overheat.

5Replace front cover.

73342 rev1 13/3/07 15:02 Page 5

66UUKKHHeellpplliinnee0088770000660022660044RReeppllaacceemmeennttPPaarrttss0088770011667766663355IIrreellaannddHHeellpplliinnee11880000440099111199

FILTERS

Replacing the HEPA

exhaust filter E

The HEPA exhaust filter should

be replaced every 6 months.

• Replacement filters can be

purchased from our replacement

parts helpline.

1Remove the front grille Eto

access the HEPA filter.

Safety cut-out

If the cleaner overheats a motor

protection thermostat will

automatically switch the motor

off. If this happens, switch the

cleaner off, unplug from the

power supply and leave the

cleaner to cool for at least 60

minutes. Check the airways for

blockages, replace the dust bag,

clean the pre-motor filter and if

necessary change the HEPA

filter.

Changing the belt

If the brush bar stops rotating it

is likely that the drive belt has

snapped (usually because the

brush has been stalled). A spare

belt is supplied. Replacement

belts can also be obtained from

Morphy Richards.

Removing the floor

nozzle cover FG

1Disconnect the cleaner from the

mains supply.

2Press the handle release pedal

and place the cleaner face

down, in the flat position on a

soft surface (eg carpet).

3Use a cross-head screwdriver to

remove the four screws

indicated F.

4Turn the cleaner over.

5While pressing the handle

release pedal lift the rear of the

top cover, unhook from the front

then completely remove the

cover G.

Replacing the belt HI

6Lift off the belt cover Î.

7Gently pull the right hand side

(belt side) of the floor nozzle

outwards and at the same time

lift the brush bar Ïout of its

location H.

8If the belt has broken, ensure all

pieces are removed. Clean the

motor shaft Ì.

9Check the brush bar end caps.

10 Fit the left hand end cap into the

floor nozzle.

11 Fit the right hand end cap onto

the brush bar.

12 Place one end of the new belt

over the motor shaft Ìand the

other around the pulley end of

the brush Ï.

13 Locate the left hand side of the

brush bar first, then while pulling

the right hand side of the nozzle

gently outwards and stretching

the belt, lower the right hand

side of the brush into its

location.

14 Rotate the brush by hand to

ensure it is correctly and

securely located.

15 IMPORTANT: Re-fit the belt

cover.

16 Replace the top cover, hooking it

in at the front first and by

pressing the handle release

pedal to allow the rear to

correctly locate J.

17 Turn the cleaner face down and

re-fit and tighten the four fixing

screws, do not overtighten.

18 Return the cleaner to its correct

working position before re-

testing.

73342 rev1 13/3/07 15:02 Page 6

Cleaning and

maintenance

Unplug from the mains before

cleaning. The vacuum cleaner,

especially the dust

compartment and all

accessories can be cleaned

using a damp cloth or a non-

abrasive cleaner and wiped dry.

HELPLINE

If you have any difficulty with

your appliance, do not hesitate

to call us.

We are more likely to be able to

help than the store from where

you bought it.

Please have the following

information ready to enable our

staff to deal with your query

quickly.

• Name of the product

• Model number as shown on the

underside of the appliance.

• Serial number as shown on

underside of the appliance.

UK Helpline 0870 0602604

Replacement Parts 0870 1676635

Ireland Helpline 1800 409119

73342 rev1 13/3/07 15:02 Page 7

YOUR TWO YEAR

GUARANTEE

It is important to retain the

retailers receipt as proof of

purchase.Staple your

receipt to this back cover

for future reference.

Please quote the following

information if the product

develops a fault. These

numbers can be found on

the base of the product.

Model no.

Serial no.

All Morphy Richards

products are individually

tested before leaving the

factory. In the unlikely event

of any appliance proving to

be faulty within 28 days of

purchase it should be

returned to the place of

purchase for it to be

replaced.

If the fault develops after

28 days and within 24

months of original

purchase, you should

contact the Helpline

number quoting Model

number and Serial number

on the product, or write to

Morphy Richards at the

address shown.

You may be asked to return

a copy of proof of

purchase.

Subject to the exclusions

set out below (see

Exclusions) the faulty

appliance will then be

repaired or replaced and

dispatched usually within 7

working days of receipt.

If you suspect a fault,

follow the simple checks

detailed below before

retrying the appliance or

calling the helpline.

• Check the filters for

blockages.

• Check the tools / tubes for

blockages.

• Check the plug is firmly in the

socket is working by trying

another appliance.

• Check the fuse in the plug.

If for any reason this item is

replaced during the 2 year

guarantee period, the

guarantee on the new item

will be calculated from

original purchase date.

Therefore it is vital to retain

your original till receipt or

invoice to indicate the date

of initial purchase.

To qualify for the 2 year

guarantee the appliance

must have been used

according to the

instructions supplied.

Exclusions

Morphy Richards shall not

be liable to replace or

repair the goods under the

terms of the guarantee

where:

1The fault has been caused

or is attributable to

accidental use, misuse,

negligent use or used

contrary to the

manufacturers

recommendations or where

the fault has been caused

by power surges or

damage caused in transit.

2The appliance has been

used on a voltage supply

other than that stamped on

the products.

3Repairs have been

attempted by persons

other than our service staff

(or authorised dealer).

4Where the appliance has

been used for hire

purposes or non domestic

use.

5Morphy Richards are not

liable to carry out any type

of servicing work, under

the guarantee.

6The guarantee excludes

consumables such as dust

bags and filters.

• This guarantee does not

confer any rights other than

those expressly set out

above and does not cover

any claims for

consequential loss or

damage. This guarantee is

offered as an additional

benefit and does not affect

your statutory rights as a

consumer.

• This guarantee is valid in

the UK and Ireland only.

Morphy Richards products are intended for household use only.

Morphy Richards has a policy of continuous improvement in product quality and

design. The company, therefore reserves the right to change the specification of its

models at any time.

The After Sales Division

Morphy Richards Ltd

Mexborough, SouthYorkshire,

England, S64 8AJ

Helpline (office hours)

UK 0870 060 2604

Republic of Ireland 1800 409119

FFoorrddeettaaiillssooffootthheerrpprroodduuccttssiinntthheeMMoorrpphhyyRRiicchhaarrddssrraannggeepplleeaasseesseeeeoouurrwweebbssiittee......

For electrical products sold within the

European Community. At the end of the

electrical products useful life it should

not be disposed of with household

waste.

Please recycle where facilities exist.

Check with your Local Authority or

retailer for recycling advice in your

country.

VC73342 MUK Rev 1 01/07

73342 rev1 13/3/07 15:02 Page 8

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Aspiradora de Morphy Richards

Morphy Richards

Morphy Richards 73270 Manual de usuario

Morphy Richards

Morphy Richards Ultralight bagless vacuum cleaner Manual de usuario

Morphy Richards

Morphy Richards Bagged cylinder Vacuum Manual de usuario

Morphy Richards

Morphy Richards IB70045 Manual de usuario

Morphy Richards

Morphy Richards Goblin Manual de usuario

Morphy Richards

Morphy Richards Storm 73215 Manual de usuario

Morphy Richards

Morphy Richards ORB CYCLONE VACUUM CLEANER - REV 3 Manual de usuario

Morphy Richards

Morphy Richards Storm hard floor cylinder vacuum cleaner Manual de usuario

Morphy Richards

Morphy Richards Ecovac 70096 Rev 2 (Page 1) Manual de usuario

Morphy Richards

Morphy Richards IB73091 Manual de usuario

Morphy Richards

Morphy Richards Scoot cylinder vacuum cleaner Manual de usuario

Morphy Richards

Morphy Richards 71077 VACUUM CLEANER Manual de usuario

Morphy Richards

Morphy Richards 732000 Supervac Manual de usuario

Morphy Richards

Morphy Richards Scoot bagless vacuum cleaner Manual de usuario

Morphy Richards

Morphy Richards IB70240 Manual de usuario

Morphy Richards

Morphy Richards IB73105 Manual de usuario

Morphy Richards

Morphy Richards ESSENTIALS BAGLESS VACUUM CLEANER Manual de usuario

Morphy Richards

Morphy Richards Ecovac 70096 Manual de usuario

Morphy Richards

Morphy Richards Topo compact vacuum cleaner Manual de usuario

Morphy Richards

Morphy Richards 73332 Manual de usuario

Morphy Richards

Morphy Richards IB73370 Manual de usuario

Morphy Richards

Morphy Richards Essentials 73179 Manual de usuario

Morphy Richards

Morphy Richards Supervac 732009 Manual de usuario

Morphy Richards

Morphy Richards IB73100 Manual de usuario

Manuales populares de Aspiradora de otras marcas

Bissell

Bissell LittleGreen Proheat 1425 Series Manual de usuario

Panasonic

Panasonic MC-YL637S147-AE Manual de usuario

NEFF

NEFF N17XH10 0 Series Manual de usuario

LG A9 Series Manual de usuario

Oreck

Oreck Cordless Captura BK51700 Series Manual de usuario

Kogan

Kogan KAVACROBVWA Manual de usuario

Kränzle

Kränzle VENTOS 50 ID Guía del usuario

EVVO

EVVO Ai35 Manual de usuario

DeWalt

DeWalt DWH200D Manual de usuario

Pontec

Pontec Pondomatic Vacuum Cleaner Manual de usuario

Cleanmaxx

Cleanmaxx PC-P007E Manual de usuario

Exido

Exido 240-114 Manual de usuario

RIDGID

RIDGID WD1685AU0 Manual de usuario

Ezviz

Ezviz RE4P Manual de usuario

STG global

STG global TANVAC HDV3000 Manual de usuario

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Manual de usuario

Factory

Factory M3340 Manual de usuario

Shop-Vac

Shop-Vac VN92 SERIES Manual de usuario