Morphy Richards 73332 Manual de usuario

Cyclonic bagless

upright vacuum cleaner

Please read and keep these instructions

Dust canister

It is important to regularly empty the canister, even if it does not appear full.

Filters

It is important that the pleated filter is shaken clean each time the dust canister is emptied,

this allows air through the appliance. Wash the canister filters regularly in warm water and

allow to air dry.

Blockages

Check the hose, tubes and tools for blockages.

Safety cut-out

If the air-flow is blocked or the filters are not regularly cleaned, a thermostat may operate.

If this happens, switch off and disconnect from the mains supply. Clear any blockage,

empty and clean the filters. Allow 60 minutes for the thermostat to reset.

Belt

Check and replace damaged or broken belt.

Height adjustment

The height adjustment only comes into effect when the handle is released by the handle

release pedal È.

Getting the best from your new cleaner...

If your cleaner is not picking up as well as it should, please check

VC73332 MUK Rev 3

If you have a problem or complaint, please call our dedicated UK based helpline

before returning your product to the retailer from where it was purchased.

UK Helpline: 0844 871 0949

Replacement Parts: 0844 873 0715

Ireland Helpline: 1800 409 119

73332 rev3 10/9/08 09:56 Page 1

IMPORTANT

SAFETY

INSTRUCTIONS

The use of any electrical

appliance requires the

following common sense

safety rules.

Primarily there is danger of

injury or death and secondly

the danger of damage to the

appliance. These are

indicated in the text by the

following two conventions:

WARNING: Danger to the

person!

IMPORTANT: Damage to the

appliance!

In addition we offer the

following safety advice.

Location

• Do not use or keep this

product outside.

• Do not store the appliance

near hot surfaces eg. ovens

or heating appliances.

Mains lead

• Do not allow the mains lead

to become strained or run

this appliance over it.

• If the electrical cable

becomes damaged, the

cable assembly must be

replaced. Do not attempt this

task yourself, contact the

helpline number that is found

at the bottom of the page.

Personal safety

• WARNING: Keep loose

clothing, hair, fingers etc.

away from the floor

nozzle whenever the

cleaner is connected to

the mains.

• WARNING: Only lift the

product by the handles

‡and ‰.

• Disconnect from the

mains supply before

attempting to clear

blockages, clear the

brush or replace the belt.

• Disconnect from the mains

supply before cleaning or

emptying the appliance.

• Never modify the cleaner in

any way.

• Never use in the presence of

explosive liquid or vapours.

• Never pick up inflammable or

poisonous liquids such as

petrol, copier toner or other

volatile substances. Never

pick up acids, asbestos or

asbestos dust.

• Never touch the plug or

cable with wet hands.

• Unprofessional repairs can

be dangerous for users.

• Use only Morphy Richards

spare parts and accessories.

• The appliance must never be

left running unsupervised.

• This appliance is intended for

domestic use only. Misuse or

use for commercial or any

other purpose will render the

guarantee invalid.

• Always disconnect the

appliance from the mains

supply after use.

• This appliance is not

intended for use by persons

(including children) with

reduced physical, sensory or

mental capabilities, or lack of

experience and knowledge,

unless they have been given

supervision or instruction

concerning use of the

appliance by a person

responsible for their safety.

• To protect against fire,

electric shock and personal

injury, do not immerse cord,

plug or cleaner in water or

other liquid.

Product safety

• Never use the appliance

without the filters being

installed.

• Never use the appliance to

vacuum hot ashes, broken

glass, sharp objects or

liquids.

• Never over-extend the hose

such that the cleaner is

pulled over. If the cleaner is

knocked over, switch off

before attempting to upright.

• Never pick the cleaner up by

the floor nozzle when

connected to the mains, use

the carrying handle.

Children

• Children do not understand

the dangers associated with

operating electrical

appliances. Never allow

children to use this

appliance.

• Children should be

supervised to ensure that

they do not play with the

appliance, or stumble over

the power cord.

Electrical

requirements

Check that the voltage on the

rating plate of your appliance

corresponds with your house

electricity supply which must

be A.C. (Alternating current).

If the socket outlets in your

home are not suitable for the

plug supplied with this

appliance, the plug should

be removed and the

appropriate one fitted.

WARNING: The plug

removed from the mains

lead, if severed, must be

destroyed, as a plug with

a bared flexible cord is

hazardous if engaged

into a live socket outlet.

Should the fuse in the 13

amp plug require changing, a

13 amp BS1362 fuse must

be fitted.

UUKKHHeellpplliinnee0088444488771100994499RReeppllaacceemmeennttPPaarrttss0088444488773300771155IIrreellaannddHHeellpplliinnee11880000440099111199

73332 rev3 10/9/08 09:56 Page 2

⁄

‹

›

ﬂ

‡

‚



ÍÓ

„

ﬁ

‰

Û Ù

FEATURES

⁄Eco Switch

(certain models only)

¤Front cover release

‹Removable front cover

›Exhaust filter grille

ﬁCarpet height adjustment

knob

ﬂFloor nozzle with powered

brush

‡Upper handle

·Flexible hose

‚Cord storage with quick

release cleat

„On/Off switch

‰Carrying handle

ÂNested extension tubes (x2)

ÊCrevice nozzle

ÁFurniture brush

ËHose clip slot

ÈHandle release pedal

ÍHose connector

ÎDust canister release

(shown page 5)

ÏDust canister lid

ÌPleated circular filter

ÓDust canister

ÔCentral mesh filter

Canister handle

ÒHose clip

ÚTurbo nozzle

(certain models only)

Û& ÙStair and Hair tool

(certain models only)

FFoorrddeettaaiillssooffootthheerrMMoorrpphhyyRRiicchhaarrddsspprroodduuccttss,,pplleeaasseesseeeeoouurrwweebbssiittee::

73332 rev3 10/9/08 09:56 Page 3

OPERATING THE

APPLIANCE

Assembly A

WARNING: Do not plug in

the cleaner until it is

assembled.

1Carefully unpack all of the

components.

2Lift the cleaner body to the

upright position.

3Remove the two screws that are

already attached to the body.

4From the rear of the cleaner,

align the handle with the groove

and slide into the body. If

necessary, use thumb and finger

pressure to slide the handle into

position.

5Fasten the handle with the two

screws.

Floor nozzle

height adjustment B

Before using the cleaner, the

floor nozzle height ﬁ must be

set to the correct height.

Choose the setting which most

closely matches your floor

surface.

• Use the TOOLS setting when

using the tools.

Note: The height adjustment

only comes into effect when the

handle is released by the handle

release pedal È.

Eco Switch C

(Certain models only)

The Eco Switch ⁄ allows you

to turn down the power when

cleaning more delicate items,

such as curtains and upholstery,

saving energy and reducing

costs.

Using on carpets

1Place the cleaner in it’s upright

position.

2Set the carpet height

adjustment knob ﬁ to the

desired position.

3Release the mains cable by

revolving the quick release cleat

‚half-a-turn and extend the

cable fully.

4Plug the cable into the mains

socket.

5Step on the handle release

pedal È to release the handle

to the desired position.

6Press the on/off button to the

‘on’ position.

IMPORTANT: To prevent damage

to carpets, never leave the

cleaner switched on in one

place for an extended period.

• Never have the brushes set too

low such that the cleaner is hard

to push.

UUKKHHeellpplliinnee0088444488771100994499RReeppllaacceemmeennttPPaarrttss0088444488773300771155IIrreellaannddHHeellpplliinnee11880000440099111199

ﬁ

⁄

73332 rev3 10/9/08 09:56 Page 4

Using the

attachments

Follow steps 1-4but set the

carpet height adjustment knob

to the TOOLS setting.

5Remove the hose connector Í

from the rear of the cleaner. Lift

the hose ·from the top handle

hook. Insert the hose clip Ò

into the hose clip slot Ë.

• Push the required attachment

firmly onto the end of the hose.

• If additional length is required,

attach one or both extension

tubes Â.

6Switch on „.

• IMPORTANT: Always fix the

hose clip Òto the main body

slot Ëwhen using the hose and

tools.

• Never over extend the hose

such that the cleaner is pulled

over.

IMPORTANT: Turning the cleaner

sideways helps prevent the

cleaner being pulled along by

the stretch hose.

Using & cleaning the

turbo nozzle

(Certain models only)

Attach the turbo nozzle Ú to

the hose end connector Í.

Following use, your turbo nozzle

may become clogged. Turn over

the nozzle and pull away any

hairs or fibres. If they are tightly

wound around the brush,

carefully snip the fibres with

scissors, being careful not to

damage the brush bar, pull away

from the brush bar and dispose.

Using the Stair and

Hair tool

(Certain models only)

Attach the stair tool Û to the

hose connector Ífor effective

stair cleaning.

Attach the hair tool Ùto the

stair tool for fantastic pet and

human hair pick-up D.

EMPTYING

Empty the dust canister

regularly even if it does not look

full, this will maintain the

performance.

1Remove the front cover ‹ by

lifting the cover release lever ¤

2Lift-up the dust canister release

Îand pull the canister away

from the main body.

3Take the canister to the dustbin.

4Turn the lid quarter-of-a-turn

anti-clockwise to unlock, lift off

the lid with pleated filter Ì, put

to one side F.

5Lift out the central mesh filter Ô

from the dust canister Ó G.

Brush clean if necessary.

6Empty out the dust canister Ó.

7Re-fit the central mesh filter.

8Shake the pleated filter Ì to

remove all dust.

9Re-fit pleated filter with lid into

the dust canister by lining up the

two arrows and turning the lid

quarter-of-a-turn clockwise to

lock.

10 Re-fit dust canister into cleaner

and push to lock into position.

11 Re-fit the front cover.

Û Ù

FFoorrddeettaaiillssooffootthheerrMMoorrpphhyyRRiicchhaarrddsspprroodduuccttss,,pplleeaasseesseeeeoouurrwweebbssiittee::

73332 rev3 10/9/08 09:56 Page 5

SAFETY CUT-OUT

If the cleaner overheats, a

motor protection thermostat will

automatically switch the motor

off. If this happens, switch the

cleaner off, unplug from the

power supply and leave the

cleaner to cool for at least

60 minutes. Check the

airways for blockages, empty

the dust canister and clean the

filters before restarting.

CLEANING THE

FILTERS

To maintain suction, the

pleated filter must be

shaken clean each time the

dust canister is emptied.

Failure to clean the filter will

reduce suction and could

damage the motor if used for a

prolonged period. This may

invalidate the guarantee. If the

filters become damaged, they

must be replaced.

Pleated filter

This must be shaken clean at

every emptying to maintain

suction. To thoroughly clean it,

wash it regularly.

To remove it from the dust

canister lid, turn the filter

quarter-of-a-turn anti-clockwise

H. Wash in warm water (no

detergent) and allow to air dry

before refitting.

Motor protection filter

The motor protection filter ıis

located underneath the dust

canister.

1Remove the dust canister.

2Lift out the filter and shake over

a dustbin.

The filter may also be washed in

water (no detergents). Allow the

filter to air dry. Ensure the filter

is thoroughly dry before refitting.

3Replace the filter.

Exhaust filter J

The exhaust filter is located

below the dust canister

compartment.

1Remove the front cover ‹.

2Remove the exhaust filter ˆby

pulling forward at the top and

lifting it away.

3Take the filter out of the cage

and shake vigorously over a

dustbin. The filter may also be

washed in warm water. Do not

use detergents. The filter must

be completely dry before re-

fitting. Allow filters to air dry

naturally.

4Replace the filter and the front

cover.

Changing the belt

If the brush bar stops rotating, it

is likely that the drive belt has

snapped (usually because the

brush has been stalled). A spare

belt is supplied. Replacement

belts can also be obtained from

Morphy Richards by calling the

helpline number at the base of

the page.

Accessing the floor

nozzle K

1Disconnect the cleaner from the

mains supply.

2Put the switch to the ‘off’

position.

3Remove the front cover and the

dust canister.

4Press the handle release pedal

and place the cleaner face

down, in a flat position on a soft

surface (eg. carpet).

5Using a flat bladed screwdriver

or a coin, rotate the three cover

fixings, a quarter-of-a-turn, from

lock to unlock K.

6Lift the base cover ˜from the

rear fixing area first, the cover

will rotate forward. Unhook the

cover from the front edge and

remove.

UUKKHHeellpplliinnee0088444488771100994499RReeppllaacceemmeennttPPaarrttss0088444488773300771155IIrreellaannddHHeellpplliinnee11880000440099111199

73332 rev3 10/9/08 09:56 Page 6

Removing rotating

brush & belt L,M

7Lift the metal belt guard ¯out

of the floor nozzle and put it

safely to one side L.

8Slide the belt past the end of the

motor drive shaft ˘. If the belt

has broken, remove all pieces

and clean the drive shaft.

9Lift the rotating brush equally

at both ends to slide it free of

the floor nozzle M. Holding the

ends of the brush, check it

rotates freely or not, if not, it

must be replaced. Call our

Helpline for replacement parts

or belts.

Re-fitting rotating

brush & belt N

10 Hook the belt over the the

drive shaft (the belt must be slid

sideways past the end of the

drive shaft). Note: The belt guard

must have been removed first,

see point 7 above.

11 Refit the belt guard, ensuring it

is correctly located. Press down

fully.

12 Pass the rotary brush through

the belt, ensuring the correct

end is located against the belt

13 Pull the brush forward (against

the pull of the belt) and locate

the square ends of the brush

into location slots in the floor

nozzle N.

14 Rotate the brush by hand to

ensure the belt is running in the

centre of it’s location on the

brush.

Refitting the floor

nozzle base cover O

15 Hook the base cover ˜ into the

front of the floor nozzle,

ensuring all four hooks are

engaged O.

16 Rotating the cover downwards

and rearwards, slowly close the

cover.

17 Tighten the three fixings, using a

screwdriver to turn the fixings a

quarter-of-a-turn to the lock

position.

Note: If the cover will not fully

close or fixings will not lock, lift

the cover slightly and rotate the

fixings until they are in the

correct position for closure.

18 Return the cleaner to the upright

position, re-fit the dust canister

and front cover. Connect to the

mains supply. Switch on to test.

HELPLINE

If you have any difficulty with

your appliance, do not hesitate

to call us.

We are more likely to be able

to help than the store from

where you bought it.

Please have the following

information ready to enable our

staff to deal with your query

quickly.

• Name of the product

• Model number as shown on the

underside of the appliance.

• Serial number as shown on

underside of the appliance.

UK Helpline 0844 871 0949

Replacement Parts 0844 873 0715

Ireland Helpline 1800 409 119

WEBSITE

You may also contact us through

our website, or visit the site to

browse and purchase

appliances, spare parts and

accessories from the extensive

Morphy Richards range.

FFoorrddeettaaiillssooffootthheerrMMoorrpphhyyRRiicchhaarrddsspprroodduuccttss,,pplleeaasseesseeeeoouurrwweebbssiittee::

73332 rev3 10/9/08 09:56 Page 7

Morphy Richards products are intended for household use only.

Morphy Richards has a policy of continuous improvement in product quality and

design. The company therefore reserves the right to change the specification of

it’s models at any time.

The After Sales Division

Morphy Richards Ltd

Mexborough, SouthYorkshire,

England, S64 8AJ

Helplines (office hours)

UK 0844 871 0949

Spare Parts 0844 873 0715

Republic of Ireland 1800 409 119

VC73332 MUK Rev 3 09/08

YOUR TWO YEAR

GUARANTEE

It is important to retain the

retailer’s receipt as proof of

purchase. Staple your receipt

to this back cover for future

reference.

Please quote the following

information if the product

develops a fault. These

numbers can be found on

the base of the product.

Model no.

Serial no.

All Morphy Richards

products are individually

tested before leaving the

factory. In the unlikely event

of any appliance proving to

be faulty within 28 days of

purchase, it should be

returned to the place of

purchase for it to be

replaced.

If the fault develops after 28

days and within 24 months

of original purchase, you

should contact the helpline

number quoting model

number and serial number on

the product, or write to

Morphy Richards at the

address shown.

You will be asked to return

the product (in secure,

adequate packaging) along

with a copy of proof of

purchase.

Subject to the exclusions set

out below (1-7), the faulty

appliance will then be

repaired or replaced and

dispatched usually within

seven working days of

receipt.

If, for any reason, this item is

replaced during the 2 year

guarantee period, the

guarantee on the new item

will be calculated from

original purchase date.

Therefore, it is vital to retain

your original receipt or

invoice to indicate the date of

initial purchase.

To qualify for the two-year

guarantee, the appliance

must have been used

according to the

manufacturer’s instructions.

For example, the filters must

have been regularly cleaned

as instructed.

Morphy Richards shall not be

liable to replace or repair the

goods under the terms of the

Guarantee where:

EXCLUSIONS

1The fault has been caused or

is attributable to accidental

use, mis-use, negligent use

or used contrary to the

manufacturer’s

recommendations or where

the fault has been caused by

power surges or damage

caused in transit.

2The appliance has been used

on a voltage supply other

than that stamped on the

products.

3Repairs have been attempted

by persons other than our

service staff (or authorised

dealer).

4The appliance has been used

for hire purposes or non-

domestic use.

5The appliance is second

hand.

6Morphy Richards are not

liable to carry out any type of

servicing work under the

guarantee.

7Consumables such as the

filters and belt are not

covered by the guarantee.

• This guarantee does not

confer any rights other than

those expressly set out

above and does not cover

any claims for consequential

loss or damage. This

guarantee is offered as an

additional benefit and does

not affect your statutory

rights as a consumer.

• This guarantee is valid in the

UK and Ireland only.

For electrical products sold within the

European Community. At the end of the

electrical products useful life, it should

not be disposed of with household

waste.

Please recycle where facilities exist.

Check with your Local Authority or

retailer for recycling advice in your

country.

73332 rev3 10/9/08 09:56 Page 8

Tabla de contenidos

Otros manuales de Aspiradora de Morphy Richards

Morphy Richards

Morphy Richards ESSENTIALS COMPACT BAGLESS VACUUM CLEANER - REV... Manual de usuario

Morphy Richards

Morphy Richards 73199 Manual de usuario

Morphy Richards

Morphy Richards VC73184 Manual de usuario

Morphy Richards

Morphy Richards IB70191 Manual de usuario

Morphy Richards

Morphy Richards Essentials Family and Pets+ Manual de usuario

Morphy Richards

Morphy Richards 73313 Manual de usuario

Morphy Richards

Morphy Richards VC73111 MUK Manual de usuario

Morphy Richards

Morphy Richards ESSENTIALS BAGLESS VACUUM CLEANER - REV 1 Manual de usuario

Morphy Richards

Morphy Richards Ultralight vacuum cleaner Manual de usuario

Morphy Richards

Morphy Richards VORTICITY Manual de usuario

Morphy Richards

Morphy Richards PremAir Cyclonic 70035 Manual de usuario

Morphy Richards

Morphy Richards Supervac Manual de usuario

Morphy Richards

Morphy Richards Scoot cylinder vacuum cleaner Manual de usuario

Morphy Richards

Morphy Richards IB70045 Manual de usuario

Morphy Richards

Morphy Richards IB70041 Manual de usuario

Morphy Richards

Morphy Richards STORM CYCLONIC vacuum cleaner Manual de usuario

Morphy Richards

Morphy Richards Supervac deluxe Manual de usuario

Morphy Richards

Morphy Richards Boxer wet & dry vacuum cleaner Manual de usuario

Morphy Richards

Morphy Richards Storm Manual de usuario

Morphy Richards

Morphy Richards IB73370 Manual de usuario

Morphy Richards

Morphy Richards BIG POD BAGLESS VACUUM CLEANER - REV 2 Manual de usuario

Morphy Richards

Morphy Richards ESSENTIAL MINI VACUUM CLEANER - REV 1 Manual de usuario

Morphy Richards

Morphy Richards Topo compact vacuum cleaner Manual de usuario

Morphy Richards

Morphy Richards BAGLESS UPRIGHT VACUUM CLEANER - REV 1 Manual de usuario

Manuales populares de Aspiradora de otras marcas

Bissell

Bissell LittleGreen Proheat 1425 Series Manual de usuario

Panasonic

Panasonic MC-YL637S147-AE Manual de usuario

NEFF

NEFF N17XH10 0 Series Manual de usuario

LG A9 Series Manual de usuario

Oreck

Oreck Cordless Captura BK51700 Series Manual de usuario

Kogan

Kogan KAVACROBVWA Manual de usuario

Kränzle

Kränzle VENTOS 50 ID Guía del usuario

EVVO

EVVO Ai35 Manual de usuario

DeWalt

DeWalt DWH200D Manual de usuario

Pontec

Pontec Pondomatic Vacuum Cleaner Manual de usuario

Cleanmaxx

Cleanmaxx PC-P007E Manual de usuario

Exido

Exido 240-114 Manual de usuario

RIDGID

RIDGID WD1685AU0 Manual de usuario

Ezviz

Ezviz RE4P Manual de usuario

STG global

STG global TANVAC HDV3000 Manual de usuario

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Manual de usuario

Factory

Factory M3340 Manual de usuario

Shop-Vac

Shop-Vac VN92 SERIES Manual de usuario