MORLEY SPRINGWOUND Manual de usuario

Buy A Morley. And Step On It.

SPRING REPLACEMENT INSTRUCTIONS FOR:

MARK 1, VAI-1, VAI-2, PBA, PBA-2, NSW OR WAH-SP (wound spring style)

Follow the below instructions to replace a broken or fatigued spring on any of the above

mentioned pedal models.

Tools you will need:

-12 mm nut driver

-5/16” nut driver

-1/4” nut driver

-Phillips Screwdriver (medium tip)

-Long tip Needle-nose pliers (2” long tip)

-3/8” Wrench (Open end or Box end)

DISASSEMBLY

1) Remove four bottom cover screws using Phillips screwdriver.

2) Remove bottom cover.

3) Remove two Chrome jack nuts and black plastic rings from 1/4” input and output jacks.

4) Remove four 1/4” nuts that hold down circuit board.

5) Slip battery snap out from battery foam slit.

6) The circuit board can now be removed from base.

7) Remove four 5/16” nuts, four 6-32 x 1/2” Phillips pan head screws and three washers that attach base to

treadle.

8) The base, treadle and spring will be completely disassembled at this point. Discard old spring.

CAUTION: Coiled spring steel version may have sharp edges especially where a break has occurred!

ASSEMBLY

1) Diagram 1 indicates the direction in which the spring should when assembled. The short side of the spring

(also indicated in diagram #1) should rest on the surface of the bracket. Although the diagrams show a pedal

with a base, the spring is to be assembled to the treadle/treadle bracket first.

2) Diagram #2 shows the proper assembly order of spring and associated components.

3) Place all components (per diagram #2) into place.

4) Place base onto treadle and align screw hole openings in base to line up with holes in treadle bracket.

5) Place a int. tooth washer on 6-32 a 1/2” screw. Using the needle-nose pliers, hold the 6-32 x 1/2” Phillips

pan head screw by the head and insert from underside of treadle bracket. (The thread should stick up in the

inside of the pedal base) Replace washer and 5/16” nut. Repeat for three remaining mounting locations. Do

not tighten any of the four nuts yet.

6) Align and center treadle to base. This can be accomplished by setting the pedal assembly on its heel end,

pushing the treadle as far toward the toe end as possible and visually centering the treadle so it is not cocked

to the right or left. This is important so the shutter is located properly between the optics.

7) Tighten the four 5/16” nuts thoroughly.

8) Set the screw tightness on each side of the treadle. To accomplish this, place the 3/8” wrench on the nut

located on the inside of the treadle/bracket assembly. Tighten bolt all the way down and loosen it one half turn

to allow treadle to move freely. Repeat for opposite side.

9) Replace circuit board, four 1/4” nuts, two black plastic rings & two chrome jack nuts.

10) Insert battery snap through the slit in battery foam.

11) Perform sound test to verify wah setting is still within acceptable range.

12) Replace bottom cover and bottom cover screws.

13) Diagram #3 shows the assembled spring.

If you need further assistance, please call 1-800-284-5172

Bill Wenzloff ext 12

Chad Montrose ext 14

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Pedal de música de MORLEY

MORLEY

MORLEY CCB1 Manual de usuario

MORLEY

MORLEY PWONEWES Manual de usuario

MORLEY

MORLEY BSOVES Manual de usuario

MORLEY

MORLEY PARTLIST Manual de usuario

MORLEY

MORLEY PBAES Manual de usuario

MORLEY

MORLEY VOLUMES Manual de usuario

MORLEY

MORLEY SLVOES Manual de usuario

MORLEY

MORLEY POWER WAH Manual de usuario

MORLEY

MORLEY PWF Manual de usuario

MORLEY

MORLEY PDW-IIES Manual de usuario

MORLEY

MORLEY AERES Manual de usuario

MORLEY

MORLEY BSPES Manual de usuario

MORLEY

MORLEY Power Wah Fuzz Manual de usuario

MORLEY

MORLEY HORSIES Manual de usuario

MORLEY

MORLEY XVPES Manual de usuario

MORLEY

MORLEY PWVSS Manual de usuario

MORLEY

MORLEY BVOES Manual de usuario

MORLEY

MORLEY DFB1 Manual de usuario

MORLEY

MORLEY XWVES Manual de usuario

MORLEY

MORLEY CWAES Manual de usuario

MORLEY

MORLEY ANALOG MULTI FX Manual de usuario

MORLEY

MORLEY EEB Manual de usuario

MORLEY

MORLEY SFB Manual de usuario

MORLEY

MORLEY JDB Manual de usuario

Manuales populares de Pedal de música de otras marcas

Behringer

Behringer ULTRA WAH UW300 Manual de usuario

Whirlwind

Whirlwind oc-bass Manual de usuario

Strymon

Strymon Lex-rotary Manual de usuario

Behringer

Behringer PB600 Manual de usuario

Lexicon

Lexicon MX200 Manual de usuario

Dunlop

Dunlop Hendrix 68 Shrine Octavio Fuzz Series Manual de usuario

Matthews Effects

Matthews Effects Whaler V2 Manual de usuario

Grid 1

Grid 1 Pedal Jeanie Manual de usuario

Amptweaker

Amptweaker tightboost Manual de usuario

Ibanez

Ibanez TS-808 Tube Screamer Overdrive Pro Manual de usuario

PuzzleSounds

PuzzleSounds DR. Q ENVELOPE FILTER Manual de usuario

BYOC

BYOC Analog Chorus Manual

Dimavery

Dimavery EPVP-50 Manual de usuario

Tefi Vintage Lab

Tefi Vintage Lab GEGÈ Manual de usuario

Pro-MIDI

Pro-MIDI G25 Manual de usuario

DW 7000 Manual de usuario

FAMC

FAMC Liquid-Foot Jr. Series Manual de usuario

Dimavery

Dimavery EPOD-50 Overdrive Manual de usuario