MORLEY SPRINGCOILED Manual de usuario

Buy A Morley. And Step On It.

SPRING REPLACEMENT INSTRUCTIONS FOR VAI-1, NSW OR PBA

(coiled spring style)

Follow the below instructions to replace a broken or fatigued spring on any of the above

mentioned pedal models.

Tools you will need:

-12 mm nut driver

-5/16” nut driver

-1/4” nut driver

-Phillips Screwdriver (medium tip)

-Long tip Needlenose pliers (2” long tip)

-3/8” Wrench (Open end or Box end)

DISASSEMBLY

1) Remove four bottom cover screws using Phillips screwdriver.

2) Remove bottom cover.

3) Remove two Chrome jack nuts and black plastic rings from 1/4” input and output jacks.

4) Remove four 1/4” nuts that hold down circuit board.

5) Slip battery snap out from battery foam slit.

6) The circuit board can now be removed from base.

7) Remove four 5/16” nuts, four 6-32 x 1/2” Phillips pan head screws and four washers that attach base to

treadle.

8) The base, treadle and spring will be completely disassembled at this point. Discard old spring.

CAUTION: Spring may have sharp edges especially where a break has occurred!

ASSEMBLY

1) Completely tighten down treadle brackets. To accomplish this, place the 3/8” wrench on the nut located on

the inside of the treadle/bracket assembly. Tighten thoroughly and repeat for other side.

2) Using diagrams 1 & 2 as guides, squeeze the spring to line up screw openings.

3) Place one 6-32 x 1/2” Phillips pan head screw into spring opening. The screw head should be on the inside

of the spring with the threads sticking up outside the spring (see Diagram #2)

4) Place spring into position (see Diagram #3).

5) Place base into treadle allowing screw to locate in position (shown in Diagram #3). Replace washer and

5/16” nut. Do not completely tighten yet.

6) Using the needlenose pliers, hold a 6-32 x 1/2” Phillips pan head screw by the head and insert from

underside of treadle bracket. (The thread should stick up in the inside of the pedal base) Replace washer and

5/16” nut. Repeat for two remaining mounting locations and do not tighten completely.

7) Align and center treadle to base. This can be accomplished by setting the pedal assembly on its heel end (to

push treadle as far toward the toe end as possible) and visually centering the treadle (so it is not cocked right

or left). This is important so the shutter is located properly between the optics.

8) Tighten the four 5/16” nuts thoroughly.

9) Completely tighten down treadle brackets. To accomplish this, place the 3/8” wrench on the nut located on

the inside of the treadle/bracket assembly. Tighten thoroughly and repeat for other side.

10) Replace circuit board, four 1/4” nuts, two black plastic rings & two chrome jack nuts.

11) Insert battery snap through the slit in battery foam.

12) Perform sound test to verify wah setting.

13) Replace bottom cover and bottom cover screws.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Pedal de música de MORLEY

MORLEY

MORLEY SFB Manual de usuario

MORLEY

MORLEY MTMES Manual de usuario

MORLEY

MORLEY PWASSES Manual de usuario

MORLEY

MORLEY PWONEW Manual de usuario

MORLEY

MORLEY PDWES Manual de usuario

MORLEY

MORLEY BSOVES Manual de usuario

MORLEY

MORLEY PCBES Manual de usuario

MORLEY

MORLEY PDWNV Manual de usuario

MORLEY

MORLEY DDB1 Manual de usuario

MORLEY

MORLEY AER2 Guía de configuración

MORLEY

MORLEY SPRINGWOUND Manual de usuario

MORLEY

MORLEY PWAES Manual de usuario

MORLEY

MORLEY CCB Manual de usuario

MORLEY

MORLEY XVO-42 Manual de usuario

MORLEY

MORLEY POB1 Manual de usuario

MORLEY

MORLEY PVOES Manual de usuario

MORLEY

MORLEY PSVES Manual de usuario

MORLEY

MORLEY PDW-IIES Manual de usuario

MORLEY

MORLEY PWF Manual de usuario

MORLEY

MORLEY POBES Manual de usuario

MORLEY

MORLEY NSWES Manual de usuario

MORLEY

MORLEY CWVES Manual de usuario

MORLEY

MORLEY SLVOES Manual de usuario

MORLEY

MORLEY BFW1 Manual de usuario

Manuales populares de Pedal de música de otras marcas

Behringer

Behringer ULTRA WAH UW300 Manual de usuario

Whirlwind

Whirlwind oc-bass Manual de usuario

Strymon

Strymon Lex-rotary Manual de usuario

Behringer

Behringer PB600 Manual de usuario

Lexicon

Lexicon MX200 Manual de usuario

Dunlop

Dunlop Hendrix 68 Shrine Octavio Fuzz Series Manual de usuario

Matthews Effects

Matthews Effects Whaler V2 Manual de usuario

Grid 1

Grid 1 Pedal Jeanie Manual de usuario

Amptweaker

Amptweaker tightboost Manual de usuario

Ibanez

Ibanez TS-808 Tube Screamer Overdrive Pro Manual de usuario

PuzzleSounds

PuzzleSounds DR. Q ENVELOPE FILTER Manual de usuario

BYOC

BYOC Analog Chorus Manual

Dimavery

Dimavery EPVP-50 Manual de usuario

Tefi Vintage Lab

Tefi Vintage Lab GEGÈ Manual de usuario

Pro-MIDI

Pro-MIDI G25 Manual de usuario

DW 7000 Manual de usuario

FAMC

FAMC Liquid-Foot Jr. Series Manual de usuario

Dimavery

Dimavery EPOD-50 Overdrive Manual de usuario