Mor Electric Heating 303 SERIES Manual de usuario

INSTALLATIONAND OPERATION INSTRUCTIONS

303, 304, 305, CRH, CRQ, CFA SERIES

CAUTION: To prevent electric shock disconnect power to heater at main service before

wiring or service.

CAUTION: Do not obstruct the front of the heater with curtains, furniture, doors,

etc. Do not place heaters under towel racks. Proper operation of the

heater requires a free flow intake and exhaust of air.

To insure proper operation, all heaters must be thermostatically

controlled.

GENERAL

These heaters are designed for 2 X 4 recessed or surface mount installation. The heaters may be wall

mounted in a vertical or horizontal position and ceiling mounted. The minimum clearance from wall box to

adjacent wall or floor is 6 inches. These heaters must not be installed without wallbox model no. 30WB.

INSTALLATION OF WALL BOX 30 WB

FOR NEW CONSTRUCTION

1.Position wall box a minimum of 6 inches from ajacent wall and floor. Secure to wall stud with nails or

screws. Wall box must be installed with front edge flush with finished wall surface. See figure 1.

2.Remove knockout in wall box for power source, and install cable clamp.

3.Insert supply cable through clamp allowing 6-8" for field wiring.

NOTE: Field wiring must enter wall box where the corner wiring compartment is located.

Warning:

Form 9940

Rev. 01/06

INSTALLATION OF WALL BOX 30WB

FOR EXISTING CONSTRUCTION

1. Carefully cut a hole measuring 9 ¼” wide by 12 ¼” long in wall. Wall box 30WB must be attached to a

wall stud on one edge. Minimum clearances of 6" must be maintained to adjacent surfaces. Attach wall

box and secure power cable as in new construction.

FIG. 1

FIELD CONVERSION FOR LOWER WATTAGE

To convert heater to a lower wattage rating. Remove red jumper from heating element (see figure 2). The

wattage will be reduced to half of the nameplate wattage. See specification chart for available wattage.

INSTALLATION OF HEATER ASSEMBLY

1. Place heater into wall box and secure with the two no. 8 x ¾ screws provided.

2. Connect power supply to heater pigtails with wirenuts or crimp terminals.

3. After field connections are made, push wires into wiring compartment and secure wiring

compartment cover to heater using no. 8 X ½” screw provided.

INSTALLATION OF GRILLE AND KNOB

1. Place the two no. 8 oval head screws into grille mounting holes.

2. Align grille with heater and secure. Be careful not to over tighten as this may cause fan blade to

strike grille.

3. To install knob, remove hole plug in grille and align flat of thermostat shaft with flat on knob. Push

knob onto shaft until knob almost touches grille.

4. For tamper-resistant installation, set thermostat with knob, remove knob and replace hole plug.

Retain knob for future use.

Form 9940

Rev. 01/06

OPERATION

1.Turn on the power supply to heater.

2.Rotate thermostat knob fully clockwise. This heater is equipped with a fan delay, so the fan will be

delayed 45-60 seconds after the element is energized.

3.Allow the room to reach desired temperature, then rotate thermostat knob counter clockwise until

thermostat clicks. Fan will continue to run for 45-60 seconds to purge warm air from heater enclosure.

The heater will continue to cycle on and off in the selected temperature range.

4.For remote thermostat operation, remove wire nut on wires marked T1 and T2. Connect single pole

remote thermostat to T1 and T2. Thermostat wiring must be the same size as power supply wiring. See

specification chart for minimum wire size.

NOTE: The wall thermostat cycles the heating element only. Direct runs of supply service leads L1

& L2 supplies continuous power to the fan motor, and the heater should be considered live at all

times. Move the disconnect switch to the off position or disconnect power at main distribution box

before any maintenance work. Turning the thermostat to low position will not disconnect the heater.

NOTE: This heater is equipped with a manual reset limit control. The front grille must be removed to

reset limit. Disconnect power before reset button is pushed.

SPECIFICATIONS

MODEL NO. VOLTS WATTAGE * BTU/HR AMPERAGE MIN. **WIRE SIZE60

°°

E3035 120 1500/750 5120/2560 12.5/6.25 12 AWG.

E3045 120 1500/750 5120/2560 12.5/6.25 12 AWG.

E3055 120 1500/750 5120/2560 12.5/6.25 12 AWG.

E3038 120 1800/900 6143/3072 15/7.5 12 AWG.

E3048 120 1800/900 6143/3072 15/7.5 12 AWG.

E3058 120 1800/900 6143/3072 15/7.5 12 AWG.

F3032 208 2000/1000 6826/3413 9.6/4.8 14 AWG.

F3042 208 2000/1000 6826/3413 9.6/4.8 14 AWG.

F3052 208 2000/1000 6826/3413 9.6/4.8 14 AWG.

H3032 240/208 2000/1000 6826/5120 8.33/4.16 14 AWG.

1500/750 3413/2560 7.22/3.6

H3042 240/208 2000/1000 6826/5120 8.33/4.16 14 AWG.

1500/750 3413/2560 7.22/3.6

H3052 240/208 2000/1000 6826/5120 8.33/4.16 14 AWG.

1500/750 3413/2560 7.22/3.6

G3032 277 2000/1000 6826/3413 7.22/3.61 14 AWG.

G3042 277 2000/1000 6826/3413 7.22/3.61 14 AWG.

G3052 277 2000/1000 6826/3413 7.22/3.61 14 AWG.

* Factory wired for higher wattage, field convertible to lower wattage. Form 9940

** Use copper wire only. All wiring must conform to N.E.C. and local electrical codes. Rev. 01/06

WARNING: It should be noted that the 3000 series units feature a fan delay control to allow for

element pre-heat and more critically fan purge of heat at the end of thermostat cycle. If the units are

turned off with disconnect while the motor is operating, the residual heat may allow the manual reset

thermal limit to cycle, this may lead to service calls and unnecessary returns of the units. To turn these

units off with the disconnect switch, the thermostat should first be turned to low position, fan

should be allowed to complete the purge cycle. These units have a label attached that states “ DO NOT

DISCONNECT UNIT WHILE FAN IS RUNNING”. This applies to any unit that has the disconnect option.

Form 9940

Rev. 01/06

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Calentador de Mor Electric Heating

Mor Electric Heating

Mor Electric Heating Salamander Manual de usuario

Manuales populares de Calentador de otras marcas

oventrop

oventrop Regucor Series Manual de usuario

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manual de usuario

ELMEKO

ELMEKO ML 150 Manual de usuario

BN Thermic

BN Thermic 830T Manual de usuario

KING

KING K Series Guía

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guía de inicio rápido

Well Straler

Well Straler RC-16B Manual de usuario

EUROM

EUROM 333299 Manual de usuario

Heylo

Heylo K 170 Manual de usuario

Eterna

Eterna TR70W Manual de usuario

Clarke

Clarke GRH15 Manual de instrucciones

IRSAP

IRSAP The Radiator Company Ovali Manual de usuario

Empire Heating Systems

Empire Heating Systems WCC65 Manual de usuario

Wetekom

Wetekom 92 86 43 Manual de usuario

Desa

Desa SPC170-F Manual de usuario

Watlow

Watlow Watrod Electric Tubular Heaters Manual de usuario

Haverland

Haverland ECO-DRY GPS Series Manual de lista de piezas

Stelpro

Stelpro ASILVC2060 Series Manual de usuario