montwill M1 Manual de usuario
Technical features:
• red display of -1999…9999 digits (optional: green, orange or blue)
• minimal installation depth: 25 mm, 27 mm, 60 mm or 71 mm without plug-in terminal
• adjustment via factory default or directly on the sensor signal
• min/max-memory
• 10 adjustable supporting points
• display flashing at threshold exceedance / undershooting
• tara function
• programming interlock via access code
• protection class IP65 at the front
• plug-in terminal
• pc-based configuration software PM-TOOL with CD and USB-adapter
• on request: devices for operating temperature of -40°…+70°C (M1O)
User Manual M1
Direct current / Direct voltage signals 0-20 mA, 4-20 mA, 0-10 VDC
M1_x1GB.pdf update: 04.11.2020
Installation size 96x48 mm (BxH)
Installation size mm (BxH) Installation size 72x36 mm (BxH)
Installation size 48x24 mm (BxH)
Identification – Direct voltage / Direct current
Please state physical unit by order, e.g. m/min.
Options – breakdown of order code:
STANDARD TYPES ORDER NUMBER
Housing dimension:
96x48x38 mm (incl. plug-in terminal)
M1-1VR4B.0001.570xD
M1-1VR4B.0001.770xD
Housing dimension:
96x24x74 mm (incl. plug-in terminal)
M1-3VR4B.0001.570xD
M1-3VR4B.0001.770xD
Housing dimension:
72x36x100 mm (incl. plug-in terminal)
M1-6VR4B.0001.570xD
M1-6VR4B.0001.770xD
Housing dimension:
48x24x54 mm (incl. plug-in terminal)
M1-7VR4A.0001.770xD
M 1- 1 V R 4 B. 0 0 0 1. 5 7 0 x D
Standard type M-Line Dimension
D physical unit
Product range 1
Version
Housing size (BxHxD) x internal version
96x48x25 mm 1
96x24x57 mm 3 Switching points
72x36x71 mm 6 0 no switching point
48x24x27 mm 7 2 relay outputs (only M1-6 devices)
Display type Protection class
Current, voltage V 1 without keypad, operation via PM-TOOL
7 IP65 / plug-in terminal
Display colour
Blue B Supply voltage
Green G 5 230 VAC
Red R 7 24 VDC galv. isolated
Orange Y
Measuring input
Number of digits 1 0/4-20 mA, 0-10 VDC
4-digit 4
Analog output
Digit height 0 without
10 mm A
14 mm B Sensor supply
0 without
Interface
without 0
Content
1. Brief description 1
2. Assembly 1
3. Electrical connection and connection examples 2
4. Function description and operation 4
4.1. Programming software PM-TOOL 4
5. Setting up the device 5
5.1. Switching on 5
5.2. Standard parameterisation (flat operation level) 5
Value assignment for control of the signal input
5.3. Programming interlock 6
Activation/Deactivation of the programming interlock or change into extended
parameterisation
5.4. Extended parameterisation 7
Superior device functions like e.g.:
- rescaling of the input signals, , 7
- parameterisation of a TARA-function, 7
- zero point slowdown of the input signal, 7
- allocation of functions onto the navigation keys, 8
- adjustment of limit values for optical alarm, 8
- safety parameter for locking of the programming, 10
- input of supporting points for the linearisation of the input signals, 10
6. Reset to default values 11
Reset of the parameter onto delivery condition
7. Alarms / Switching points 12
Functional principle of the optical switching points
8. Technical data 13
9. Safety advices 15
10. Error elimination 16
2. Assembly
1
1. Brief description / 2. Assembly
Please read the Safety advices on page 16 before installation and keep this user manual for
future reference.
The example given below shows a device in housing size 96x48mm.
1. After removing the fixing elements, insert the device.
2. Check the seal to make sure it fits securely.
3. Click the fixing elements back into place and tighten the clamping screws by hand. Then
use a screwdriver to tighten them another half a turn.
CAUTION! The torque should not exceed 0.1 Nm!
1. Brief description
The panel instrument M1-x1 is a 4-digit device for direct voltage and direct current signals
and a visual limit value monitoring via the display. The configuration happens via three front
keys or via the optional PC-software PM-TOOL. An integrated programming lock prevents
unrequested changes of the parameter and can be unlocked again via an individual code.
The electrical connection happens on the rear side via plug-in terminals.
Selectable functions like e.g. the recall of the min/max-value, a zero point slowdown, a direct
change of the limit value in operating mode and additional measuring supporting points for a
linearisation of the input signal, complete the modern device concept.
Sealing
48,0
96,0
3,0
38,0
Installation depth
incl. plug-in terminal
Gap for
physical unit
3. Electrical connection
2
3. Electrical connection
Type M1-1VR4B.0001.570xD (96x48 mm)
Type M1-3VR4B.0001.570xD (96x24 mm)
Type M1-1VR4B.0001.770xD (96x48 mm)
Type M1-3VR4B.0001.770xD (96x24 mm)
Type M1-7VR4A.0001.770xD (48x24 mm)
Type M1-6VR4B.0001.570CD / M1-6VR4B.0001.770xD (Housing 72x36 mm)
123 4 5
0/4...20 mA
_
+
0...10 V
_
+
230 VAC
3 VA
N L
_
<
12345
24 VDC
1 VA
+
0/4...20 mA
_
+
0...10 V
_
+
_
_
<
230 VAC
or
24 VDC
+
_
-/+ 10 V
-/+ 0/4 - 20 mA
0 V
Signal input
N L
Option:
11 12 13 14 15 16
3
3. Electrical connection
Connection examples:
Below you find some connection examples, which demonstrate some practical applications:
1 2 3 4 5
24 VDC
_
M1-1/3/7 in combination with
a 2-wire-sensor 4-20 mA
+
_
1 2 3 4 5
_
M1-1/3/7 in combination with
a 3-wire-sensor 0/4-20 mA
+
1 2 3 4 5
_
M1-1/3/7 in combination with
a 3-wire-sensor 0-10 V
+
+
_
+
_
+_+_+
10 11
M1-6
24 VDC
10 11
M1-6
24 VDC
10 11
M1-6
1 2 3 4 5
230 VAC
_
M1-1/3 in combination with
a 2-wire-sensor 4-20 mA
+
1 2 3
24 VDC
_
+
+
_
4 5
24 VDC
+
+
_
L
N
1 2 3 4 5
M1-1/3 in combination with
a 3-wire-sensor 0/4-20 mA
M1-1/3 in combination with
a 3-wire-sensor 0-10 V
24 VDC
10 11
M1-6
230 VAC
10 11
M1-6
230 VAC
10 11
M1-6
LNLN
4. Function description and operation
Level Button Description
Menu level
Change to parameterization level with the relevant parameters
For navigation at the menu level
Parameter
level
To confirm the changes made at the parameterization level
To change the value or setting
4
4. Function description and operation
Operation
The operation is divided into two different levels.
Menu Level
Here it is possible to navigate between the individual menu items.
Parameterization level:
The parameters stored in the menu item can be parameterized here.
Functions that can be adjusted or changed are always indicated with a flashing of the
display. Adjustments made at the parameterization level should be always confirmed by
pressing the [P] key to save them. However, the display automatically saves all adjustments
and then switches to operation mode if no further keys are pressed within 10 seconds.
4.1. Programming via configuration software PM-TOOL-MUSB4:
You receive the software on CD incl. an USB-cable with a device adapter. The connection is
done via a 4-pole micromatch connector plug on the back and the PC is connected via an
USB connector plug.
System requirements: PC with USB interface
Software: Windows XP, Windows Vista
With this tool the device configuration can be created, skipped and saved on the PC. Via the
easy to handle program surface the parameter can be changed, whereat the mode of
operation and the possible selection options can be preset via the program.
CAUTION!
During parameterisation with connected measuring signal, make sure that the measuring
signal has no mass supply to the programming plug. The programming adapter is galvanic
not isolated and directly connected with the PC. Via polarity of the input signal, a current can
discharge via the adapter and destroy the device as well as other connected components!
Menu level Parameter level
Example
5
5.1. Switching on
Once the installation is complete, you can start the device by applying the current loop.
Check beforehand once again that all the electrical connections are correct.
Starting sequence
For 1 second during the switching-on process, the segment test ( ) is displayed,
followed by an indication of the software type and, after that, also for 1 second, the software
version. After the start-up sequence, the device switches to operation/display mode.
5.2. Standard parameterization:
To be able to parameterize the display, press the [P] key in operating mode for 1 second.
The display then changes to the menu level with the first menu item .
5. Setting up the device
Menu level Parameterization level
Selection of the input signal,
Default:
There are several measuring inputs options: 0/4-20 mA or 0-10 VDC signals as
the works calibration (without application of the sensor signal) and as the
sensor calibration (with the sensor applied). Confirm the selection with [P] and the
display switches back to menu level.
Setting the measuring range end value, :
Default:
Set the end value from the smallest to the highest digit with [▲] [▼] and confirm
each digit with [P]. A minus sign can only be parameterized on the highest value
digit. After the last digit, the display switches back to the menu level. If was
selected as the input option, one can only select between and With ,
only the previously set display value is taken over, and with , the device takes
over both the display value and the analogue input value.
Setting the measuring range start/offset value, :
Default:
Enter the start/offset value from the smallest to the highest digit [▲] [▼] and
confirm each digit with [P]. After the last digit the display switches back to the
menu level. If was selected as the input option, one can only select between
and With , only the previously set display value is taken over, and
with , the device takes over both the display value and the analogue input
value.
5. Setting up the device
6
5. Setting up the device
Menu level Parameterization level
Setting the decimal point, :
Default:
The decimal point on the display can be moved with [▲] [▼] and confirmed with
[P]. The display then switches back to the menu level again.
Setting the display time, :
Default:
The display time is set with [▲] [▼]. The display moves up in increments of 0.1 up
to 1 second and in increments of 1.0 to 10.0 seconds. Confirm the selection by
pressing the [P] button. The display then switches back to the menu level again.
5.3. Programming interlock
Activation/deactivation of the programming lock and completion of the
standard parameterization,
Default:
Choose between the deactivated key lock (works setting) and the activated
key lock with the aid of the [▲] [▼] keys. Make the selection with [P]. After
this, the display confirms the settings with ", and automatically switches to
operating mode. If was selected, the keyboard is locked. To get back into the
menu level, press [P] for 3 seconds in operating mode. Now enter the (works
setting ) that appears using the [▲] [▼] keys plus [P] to unlock the keyboard.
appears if the input is wrong.
dann
7
5. Setting up the device
Menu level Parameterization level
Rescaling the measuring input values,
With the aid of this function, one can rescale the input value of e.g. 19,5 mA
(works setting) without applying a measuring signal. If sensor calibration has been
selected, these parameters are not available.
Rescaling the measuring input values,
With the aid of this function, one can rescale the input value of e.g. 3,5 mA (works
setting) without applying a measuring signal. If sensor calibration has been
selected, these parameters are not available.
Setting the tare/offset value,
Default:
The given value is added to the linerarized value. In this way, the characteristic
line can be shifted by the selected amount.
Zero point slowdown,
Default:
With zero point slowdown, a value range around zero can be preselected at which
the display shows zero. If, for example, a 10 is set, the display would show a zero
in the range from -10 to +10 and continue below it with -11 and above it with +11.
5.4. Extended parameterization
By pressing the [▲] &[▼] keys during standard parameterization for one second, the
display switches to the extended parameterization mode. Operation is the same as in
standard parameterization.
Otros manuales para M1
6
Este manual sirve para los siguientes modelos
7
Tabla de contenidos
Otros manuales de Instrumento de medición de montwill
montwill
montwill M3-34H Manual de usuario
montwill
montwill M3 Series Manual de usuario
montwill
montwill M2-1F Series Manual de usuario
montwill
montwill MB2-2V Manual de usuario
montwill
montwill M2 Series Manual de usuario
montwill
montwill M2 Series Manual de usuario
montwill
montwill M2-14 Manual de usuario
montwill
montwill M3-F Manual de usuario
montwill
montwill M3 Series Manual de usuario
montwill
montwill M1 Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario