Molex 63819-7670 Manual de usuario

Hand Crimp Tool for Wire-to-Wire and Wire-to-Board Terminals

Doc No: ATS-6381976HM Release Date: 06-23-10 UNCONTROLLED COPY Page 1 of 6

Revision: C Revision Date: 07-16-15

TYPE 4A

CONDUCTOR

BRUSH

STRIP LENGTH

SEAM

CONDUCTOR

CRIMP HEIGHT

CUT-OFF

TAB

BELL MOUTH

BEND UP

TWISTING

ROLLING

BEND DOWN

WIRE

INSULATION CRIMP

▲SEE NOTE

Application Tooling

Specification Sheet

Modular Crimp Head

Order No. 63819-7670

Hand Crimp Tool

Order No. 63819-7600

FEATURES

A full cycle ratcheting hand tool ensures complete crimps

Ergonomically designed soft handles

Precisely designed crimping profiles with simple contact positioning

Easy handling due to outstanding force ratio

Modular Crimp Head is removable and can be use in the Air Powered Tool Order No.63816-0100,

accompanied by Air Powered Crimp Adapter (Order No. 63816-0700).

Can also be used in the Battery Powered Tool Order No.63816-0200 (110 V) or 63813-0250 (220 V),

accompanied by Battery Powered Crimp Adapter (Order No. 63816-0600).

SCOPE

Products: 3.96mm (.156”) Pitch Wire-to-Wire and 6.50mm (.256”) Pitch Wire-to-Board Crimp Terminals,

16-20 AWG.

Terminal

Series No.

Terminal Order No.

Wire Size

Insulation Diameter (2)

Strip Length

Loose Piece

Reel (1)

AWG

mm2

In.

50597

50597-8100

50597-8000

1.30

3.0-3.3

.118-.130

2.70-3.30

.106-.130

0.80

2.8-3.0

.110-.118

0.50

2.4-2.7

.094-.106

50599

50599-8100

50599-8000

1.30

3.0-3.3

.118-.130

0.80

2.8-3.0

.110-.118

0.50

2.4-2.7

.094-.106

(1) Customer to cut off terminal from reel: 0.25mm (.010”) maximum Cut-off Tab.

(2) See crimp specification for the individual Insulation Diameter.

DEFINITION OF TERMS

Hand Crimp Tool for Wire-to-Wire and Wire-to-Board Terminals

Doc No: ATS-6381976HM Release Date: 06-23-10 UNCONTROLLED COPY Page 2 of 6

Revision: C Revision Date: 07-16-15

Figure 2

WIRE

TERMINAL

LOCATOR

INSULATION

PUNCH

INSULATION

ANVIL

WIRE STOP

BLADE

CONDUCTOR ANVIL

CONDUCTOR

PUNCH

WIRE

INSULATION

PUNCH

TERMINAL

WIRE STOP BLADE

Figure 1

▲Insulation Crimp Note:

Due to the terminal’s insulation grip design and/or

insulation diameter range, this tool uses “overlap”

form geometry in the insulation punch. This

produces an overlap insulation crimp (A620 –

compliant). While the insulation punch profile may

appear “lopsided”, this is a normal condition for this

tool. See figure to the right. (Some tools with

multiple crimp pockets may not have the “overlap”

profile on all pockets).

CONDITIONS:

After crimping, the crimp profiles should measure the following (see notes on page 4).

Terminal

Series No

Wire Size

Conductor Crimp

Insulation Crimp

Pull Force

Minimum

Profile

Height (Ref.)

Width (Ref.)

Height (Ref.)

Width (Ref.)

AWG

mm2

In.

Lb.

AWG 16

AWG 18

AWG 20

50597

1.30

1.21-1.31

.048-.052

2.00

.079

3.80

.150

3.00

.118

127.49

28.66

0.80

1.16-1.26

.046-.050

2.00

.079

3.70

.146

3.00

.118

88.26

19.84

0.50

1.02-1.12

.040-.044

2.00

.079

3.60

.142

3.00

.118

58.84

13.23

50599

1.30

1.21-1.31

.048-.052

2.00

.079

3.80

.150

3.00

.118

127.49

28.66

0.80

1.16-1.26

.046-.050

2.00

.079

3.70

.146

3.00

.118

88.26

19.84

0.50

1.02-1.12

.040-.044

2.00

.079

3.60

.142

3.00

.118

58.84

13.23

OPERATION

Open the tool by squeezing the handles together, at the end of the closing stroke, the ratchet mechanism will

release the handles, and the hand tool will spring open.

Crimping Terminals

1. Lift the wire stop blade up.

OVERLAP

INSULATION

CRIMP

OVERLAP FORM GEOMETRY

ANVIL

PUNCH

WIRE

Hand Crimp Tool for Wire-to-Wire and Wire-to-Board Terminals

Doc No: ATS-6381976HM Release Date: 06-23-10 UNCONTROLLED COPY Page 3 of 6

Revision: C Revision Date: 07-16-15

2. Insert the terminal fully into the correct profile until the terminal is fully seated and stops.

3. Bring down the wire stop blade.

4. Slide the pre-stripped wire into the wire stop blade. See Figure 1. Be sure to hold the wire in place until the

terminal is fully crimped. See Figure 2.

5. Close the tool until the ratchet releases, the tool handles will then spring open.

6. Lift the wire stop blade up if it is still in down position.

7. Carefully remove the crimped terminal.

Note: The tamper proof ratchet action will not release the tool until it has been fully closed.

Maintenance

It is recommended that each operator of the tool be made aware of, and responsible for, the following

maintenance steps:

1. Remove dust, moisture, and other contaminants with a clean brush, or soft, lint free cloth.

2. Do not use any abrasive materials that could damage the tool.

3. Make certain all pins; pivot points and bearing surfaces are protected with a thin coat of high quality machine

oil. Do not oil excessively. The tool was engineered for durability but like any other equipment it needs

cleaning and lubrication for a maximum service life of trouble free crimping. Light oil (such as 30 weight

automotive oil) used at the oil points, every 5,000 crimps or 3 months, will significantly enhance the tool life.

4. Wipe excess oil from hand tool, particularly from crimping area. Oil transferred from the crimping area onto

certain terminations may affect the electrical characteristics of an application.

5. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping dies,

and store the tool in a clean, dry area.

Miscrimps or Jams

Should this tool ever become stuck or jammed in a partially closed position, Do Not force the handles open or

closed. The tool will open easily by lifting the ratchet release lever. See Figure 6.

Warranty

This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All vital

components are long life tested. All tools are warranted to be free of manufacturing defects for a period of 30

days. Should such a defect occur, we will repair or exchange the tool free of charge. This repair or exchange will

not be applicable to altered, misused, or damaged tools. This tool is designed for hand use only. Any clamping,

fixturing, or use of handle extensions voids this warranty.

CAUTION: Repetitive use of this tool should be avoided.

Hand Crimp Tool for Wire-to-Wire and Wire-to-Board Terminals

Doc No: ATS-6381976HM Release Date: 06-23-10 UNCONTROLLED COPY Page 4 of 6

Revision: C Revision Date: 07-16-15

CAUTIONS:

1. Manually powered hand tools are intended for low volume or field repair. This tool is NOT intended for

production use. Repetitive use of this tool should be avoided.

2. Insulated rubber handles are not protection against electrical shock.

3. Wear eye protection at all times.

4. Use only the Molex terminals specified for crimping with this tool.

Notes:

1. This tool should only be used for the terminals and wire gauges specified on this sheet.

2. This tool is not adjustable for crimp height, however crimp force is adjustable (See instructions above).

Variations in tools, terminals, wire stranding and insulation types may affect crimp height.

3. This tool is intended for standard conductor sizes. It may not give a good insulation crimp support for all

insulation sizes.

4. Molex does not repair hand tools (see warranty above). The replacement parts listed are the only parts

available for repair. If the handles or crimp tooling is damaged or worn, a new tool must be purchased.

5. Pull force should be used as the final criteria for an acceptable crimp. Pull force is measured with no

influence from the insulation crimp. The insulation should be stripped long (1/2 in.) so the insulation grips

on the terminal do not grip the wire insulation or the conductor. Refer to Molex Quality Crimping

Handbook 63800-0029 for additional information on crimping and crimp testing.

6. Molex does not certify crimp hand tools.

CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling.

Hand Crimp Tool for Wire-to-Wire and Wire-to-Board Terminals

Doc No: ATS-6381976HM Release Date: 06-23-10 UNCONTROLLED COPY Page 5 of 6

Revision: C Revision Date: 07-16-15

MODULAR

CRIMP

HEAD

BATTERY

POWER

CRIMP

ADAPTER

LOCKING

PINS

LOCKING PINS

BATTERY

POWERED

TOOL

AIR

POWER

TOOL

MODULAR

CRIMP HEAD

LOCKING

PINS

LOCKING

PINS

AIR POWER

CRIMP

ADAPTER

Applications for the Modular Crimp Head

WARNING: NEVER operate, service, install, or adjust this Modular Crimp Head without proper instruction

and without first reading and understanding the instructions in the proper Manual or Specification Sheet.

See Chart below for the correct Manual or Specification Sheet.

WARNING: NEVER install tooling or service this tool while it is into any power source. Disconnect the

power by unplugging or turn off the Actuator from its power source.

CAUTION: Keep fingers away from the crimping area when operating this tool. It may cause severe injury.

CAUTION: Wear safety glasses when operating or serving this tool.

The chart below shows all applications for this Modular Crimp Head.

Modular Crimp Head

Order No.

Tool

Order no.

Tool

Description

Adapter

Order No.

Adapter

Description

Figure

No.

63819-7670

63816-0000

Hand Crimp Frame (Short)

N/A

63816-0050

Hand Crimp Frame (Long)

N/A

63816-0200

Battery Power Tool (110 V)

63816-0600

Battery Power Crimp Adapter

63816-0250

Battery Power Tool (220 V)

63816-0600

Battery Power Crimp Adapter

63816-0100

Air Power Tool

63816-0700

Air Power Crimp Adapter

Applications for the Modular Crimp Head

Hand Crimp Tool

Battery Powered Tool

Air Powered Tool

Figure 3

Figure 4

Figure 5

MODULAR

CRIMP

HEAD

LOCKING

PINS

HAND CRIMP

FRAME LONG

OR SHORT

Hand Crimp Tool for Wire-to-Wire and Wire-to-Board Terminals

Doc No: ATS-6381976HM Release Date: 06-23-10 UNCONTROLLED COPY Page 6 of 6

Revision: C Revision Date: 07-16-15

RATCHET

RELEASE LEVER

HANDLE

SPRING

CRIMPING

SPRING (2)

Figure 6

M4 X 14mm

LONG BHCS

PARTS LIST

Hand Crimp Tool 63819-7600

Item

Order Number

Description

Quantity

63819-7670

Modular Crimp Head

1 (Ref)

63816-0050

Hand Crimp Frame (Long)

1 (Ref)

63819-7675

Locator

63816-0001

Locking Pin

63600-0525

Handle Spring

63600-0520

Crimping Spring

Visit our Web site at http://www.molex.com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Herramientas de crimpado de molex

molex

molex CR5974 Manual de usuario

molex

molex 63811-1200 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex Perma-Seal 64005-4500 Manual de usuario

molex

molex 11-01-0185 Manual de usuario

molex

molex 63827-8200 Manual de usuario

molex

molex 57030-3000 Manual de operación y mantenimiento

molex

molex 63813-2100 Manual de usuario

molex

molex 63811-8300 Manual de usuario

molex

molex AT 1610 Manual de usuario

molex

molex CR5907 Manual de usuario

molex

molex 63819-2800 Manual de usuario

molex

molex AT-1300 Manual de usuario

molex

molex ServiceGrade Guía del usuario

molex

molex 207129 Series Manual de usuario

molex

molex 64005-6400 Manual de usuario

molex

molex 63811-7100 Manual de usuario

molex

molex 63827-6070 Manual de usuario

molex

molex RHT-4754 Manual de usuario

molex

molex AT-200 Manual

molex

molex 207129 Series Manual de usuario

molex

molex 63827-3170 Manual de usuario

molex

molex 207129 Series Manual de usuario

Manuales populares de Herramientas de crimpado de otras marcas

Panduit

Panduit CT-1000 Guía del administrador

JST

JST CS 10 Manual de usuario

Danfoss

Danfoss ET4200 Manual de usuario

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manual de usuario

TE Connectivity

TE Connectivity 2063528-1 Manual de usuario

Tyco Electronics

Tyco Electronics 69156-1 Manual de usuario

CRH

CRH CRL CBLHCT1 Manual de usuario

Emerson

Emerson Klauke ES 105CFM Manual de usuario

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Manual de instrucciones

Danfoss

Danfoss ET4350 Manual de usuario

Milwaukee

Milwaukee M18 Manual de usuario

HOGERT

HOGERT HT1P169 Manual de usuario

Textron

Textron ESG105L Manual de usuario

Tyco Electronics

Tyco Electronics 90035-3 Manual de usuario

Emerson

Emerson Klauke ES 20RMCCFB Manual de usuario

Continental Refrigerator

Continental Refrigerator PC150HD Manual de usuario

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Manual de usuario

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manual de usuario

molex 63819-7670 Manual de usuario

Manuales populares de Herramientas de crimpado de otras marcas