Modern Flames SPS-50B Manual de usuario
SPECTRUM SLIMLINE WALL MOUNT/RECESSED ELECTRIC FIREPLACE
Model# : SPS-50B SPS-60B SPS-74B SPS-100B
OWNER’S MANUAL
AC 120V 60Hz 1465W (5000BTUs)
WARNING
Read and understand this entire owner’s manual, including all safety
information, before plugging in or using this product. Failure to do so could
result in fire, electric shock, or serious personal injury.
CAUTION
Keep this owner’s manual for future reference. If you sell or give this
product away, make sure this manual accompanies this product.
AFFIX SERIAL NUMBER LABEL HERE
FOR FUTURE REFERENCE
2
IMPORTANT SAFETY INFORMATION!
WARNING
Read all instructions before installing or using this heater.
This heater is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If
provided, use handles when moving this heater. Keep combustible materials, such as
furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front of
the heater, and keep them away from the sides and rear.
Extreme caution is necessary when any heater is used by or near children or invalids and
whenever the heater is left operating and unattended.
Do not operate any heater after it malfunctions. Disconnect power at service panel and have
heater inspected by a reputable electrician before reusing.
Do not use outdoors.
To disconnect heater, turn controls to off, and turn off power to heater circuit at main disconnect
panel (or operate internal disconnect switch if provided).
Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may
cause an electric shock, fire, or damage the heater.
To prevent a possible fire, do not block air intakes or exhaust in any manner.
A heater has hot arcing or sparking parts inside. Do not use in areas where gasoline, paint,
flammable vapors, or liquids are used or stored.
Use this heater only as described in this manual. Any other use not recommended by
the manufacturer may cause fire, electric shock, or injury to persons.
This heater may include an audible or visual alarm to warn that parts of the heater are getting
excessively hot. If the alarm sounds (or illuminates), immediately turn the heater off and inspect
for any objects on or adjacent to the heater that may have blocked the airflow or otherwise
caused high temperatures to have occurred. DO NOT OPERATE THE HEATER WITH THE
ALARM SOUNDING (OR ILLUMINATING).
ALWAYS plug heaters directly into a wall outlet/receptacle. NEVER use with an
extension cord or relocatable power tap (outlet/power strip).
NEVER use this heater in bathrooms, laundry rooms, or any other location where the heater
could fall into a bathtub, pool,become damp, or come in contact with water.
AVOID FIRE! Regularly inspect all air vents to make sure they are free from dust, lint, or other
blockage. Unplug the unit and clean with a vacuum ONLY.DO NOT rinse or get wet.
ALWAYS mount to wall bracket before use. DO NOT set on the floor, or other surface, to use.
NEVER use a wall mount bracket from another manufacturer.
This product is not intended to be a primary heat source. It is for supplemental heat only.
INDOOR use only! NEVER use this heater outdoors! Doing so may result in electric shock!
ALWAYS disconnect this unit from the power supply before performing any assembly or
cleaning, or before relocating the electric fireplace.
3
NEVER leave this heater unattended. ALWAYS unplug this heater when not in use.
ALWAYS store this heater in a dry location. NEVER use the fireplace if it has become wet.
NEVER plug this heater into an outlet that is old,cracked, or has any loose wires or
connections. Plugging this heater into a faulty outlet could result in electric arcing within the
outlet that could cause the outlet to overheat or catch fire.
ALWAYS check your heater cord and plug connections with each use.
i) MAKE SURE the plug fits tight in the outlet. Faulty wall outlet connections or loose plugs
can cause the outlet to overheat.
ii) Heaters draw more current than small appliances. Overheating may occur even if it has
not occurred with the use of other appliances.
iii) During use check frequently to see if the plug outlet or face plate is HOT.
iv) If the outlet or face plate is HOT,discontinue use immediately and have a qualified
electrician inspect and/or replace the faulty outlets.
The power cord supplied with the heater has three
prongs: two flat blades (live and neutral) and one
round pin (ground). If a 3-slot receptacle is not
available, an adapter MUST be used. The adapter
MUST be properly grounded to the outlet box (see
figure at right). [NOTE: Adapter NOT INCLUDED.]
SAVE THESE INSTRUCTIONS.
Preparation
This product includes a GLASS panel. Always use extreme caution when handling
glass. Failure to do so could result in personal injury or property damage.
Remove all parts and hardware from the carton and place them on a clean, soft, dry surface. Parts and
assembly steps are grouped for wall-hanging or recessing use. Check the parts list to make sure nothing
is missing. Dispose of packaging materials properly. Please recycle whenever possible.
You will need the following tools (not included): Phillips screwdriver, stud finder, level, tape measure,
electric drill, 1/4” wood drill bit, hammer.
4
Parts and Hardware
A– Fireplace
B– Screws
C– Drywall anchors
D- Remote Control
E-Instruction manual
F-Wall Bracket
Fixed on back of firebox
G-Small glacier
crystals
H - Log set
I - Metal bracket
For wall recessed
purpose
J - “L”shape
bracket
Specification and Dimension
PRODUCT DIMENSIONS
Model
Number
A
B
C
D
E
F
G
H
SPS-50B
49-3/4"
[1262mm]
17"
[430mm]
4- 5/8"
[117mm]
48- 7/16"
[1230mm]
15- 5/8"
[397mm]
4"
[101mm]
46"
[1168mm]
12"
[306mm]
SPS-60B
59-3/4"
[1516mm]
17"
[430mm]
4- 5/8"
[117mm]
58- 7/16"
[1484mm]
15- 5/8"
[397mm]
4"
[101mm]
56"
[1422mm]
12"
[306mm]
SPS-74B
73-3/4"
[1872mm]
17"
[430mm]
4- 5/8"
[117mm]
72- 7/16"
[1840mm]
15- 5/8"
[397mm]
4"
[101mm]
70"
[1778mm]
12"
[306mm]
SPS-100B
99-3/4"
[2532mm]
17"
[430mm]
4- 5/8"
[117mm]
98- 7/16"
[2500mm]
15- 5/8"
[397mm]
4"
[101mm]
96"
[2438mm]
12"
[306mm]
5
Installation and Assembly
Your appliance is a wall-mounted, recessed, and/or mantel installed appliance. Select a suitable location
that is not susceptible to moisture and is away from drapes, furniture and high traffic areas.
NOTE: Follow all National and local electrical codes.
MINIMUM CLEARANCE TO COMBUSTIBLES
Measurements are taken from the glass front.
Bottom 0" Top 11.8" (300mm) to mantel
Sides 0" Top 11.8" (300mm) to ceiling
Back 0"
MINIMUM MANTEL CLEARANCES
WARNING
WHEN USING PAINT OR LACQUER TO FINISH THE MANTEL, THE PAINT OR LACQUER MUST BE
HEAT RESISTANT TO PREVENT DISCOLOURATION.
6
Front glass removal / installation
A. With one hand on the front glass to prevent it from falling, remove the two screws (1 per side) from the
side of the appliance (Fig. 1-1). Set the screws aside.
B. Carefully lift the front glass up and away from the appliance (Fig. 1-2 ). Place it face down on a soft,
non-abrasive surface.
C. Reverse these steps to install the front glass.
Fig. 1-1
Fig. 1-2
7
Recessed pre-installation
Due to the many different materials used on different walls, it is highly recommended that you
consult your local builder before you install this appliance on the wall.
A. Select a location that is not prone to moisture and is located at least 36” (94.1cm) away from
combustible materials such as curtain drapes, furniture, bedding, paper, etc.
B. Measure the appliance and create a rough-in frame with electrical (see below “framing”).
C. Remove the front glass (see “front glass removal / installation” section).
D. Hold the appliance up to ensure it will fit into the framing.
Framing Hole Size
Model Number
A
B
C
SPS-50B
48- 3/4" [1238mm]
16" [406mm]
3-7/8”(98mm)
SPS-60B
58- 3/4" [1492mm]
16" [406mm]
3-7/8”(98mm)
SPS-74B
72- 3/4" [1848mm]
16" [406mm]
3-7/8”(98mm)
SPS-100B
98- 3/4" [2508mm]
16" [406mm]
3-7/8”(98mm)
8
Fully recessed installation
A. Remove power cord and complete hardwiring (see “hardwiring installation” section).
B. Mark location for the screws according to the dimensions as below. (Figure 2-1)
Figure 2-1
C. Fix the two metal brackets (1per side), with 4 screws (supplied) through wood stud. (Figure 2-2)
Wood Stud
Figure 2-2
9
D. Remove the four screws (2 per side) from the side of the appliance and remove the brackets
(Fig. 2-3). Set the screw/brackets aside.
Figure 2-3
E. Insert the appliance into the rough-in frame and then secure it by installing 4 screws and two brackets
(supplied) through the side holes (Fig. 2-4).
Figure 2-4 Figure 2-5
F. Install media (see “media installation” section). You must complete this step before moving onto
the next step.
G. Re-install the front glass
10
Wall mounted installation
Due to the many different materials used on different walls, it is highly recommended
that you consult your local builder before you install this appliance on the wall.
A.Select a location that is not prone to moisture and is located at least 36" (914mm)
away from combustible materials such as curtain drapes, furniture, bedding, paper,
etc.
B.Have two people hold the appliance against the wall to determine the final
location.
C.Place unit face down on a soft, non abrasive surface. Remove the bracket from
the back of the unit by removing the screws, refer to Figure 1.
D.Mark location, then mount the bracket(s) onto the wall using the supplied screws.
This bracket MUST have the hooks facing upward and be level. NOTE: It is
strongly recommended that the
mounting bracket (E) be
Screwed into the wall studs
where possible. If the wall
studs cannot be used, ensure
the supplied plastic anchors are used to affix the bracket to the wall and the
bracket is adequately secured.
E. With the wall mounting bracket installed have two people lift the appliance up and
insert the two hooks on the bracket into the two slots on the back of the appliance.
F. Check the appliance for stability ensuring that the bracket will not pull free from
the wall
SPS-50B Wall Bracket Illustrated
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Chimenea de interior de Modern Flames
Modern Flames
Modern Flames Sunset Charred Oak Instrucciones de funcionamiento
Modern Flames
Modern Flames ORION OR26-TRAD Manual de usuario
Modern Flames
Modern Flames AL1500CLX Guía rápida
Modern Flames
Modern Flames NOVA 60 Instrucciones originales
Modern Flames
Modern Flames LPM-9616/INT Instrucciones de funcionamiento
Modern Flames
Modern Flames AMBIANCE LINEAR 40 Instrucciones originales
Modern Flames
Modern Flames OR30-MULTI-INT Manual de usuario
Modern Flames
Modern Flames Sedona Pro Multi Instrucciones de funcionamiento
Modern Flames
Modern Flames OR52-SLIM Manual de usuario
Modern Flames
Modern Flames HF900CBI Instrucciones de instalación y mantenimiento
Modern Flames
Modern Flames OR26-TRAD-INT Manual de usuario
Modern Flames
Modern Flames SC36-B Instrucciones de instalación y mantenimiento
Modern Flames
Modern Flames Sunset Charred Oak Instrucciones de funcionamiento
Modern Flames
Modern Flames Landscape Pro Slim Series Instrucciones de funcionamiento
Modern Flames
Modern Flames OR52-MUTLI Manual de usuario
Modern Flames
Modern Flames Landscape Pro Multi Series Instrucciones de funcionamiento
Modern Flames
Modern Flames Landscape Pro Multi Guía de inicio rápido
Modern Flames
Modern Flames ORION OR52-MULTI Manual de usuario
Modern Flames
Modern Flames RS-2621-EU Manual de usuario
Modern Flames
Modern Flames AL 95 Manual de usuario
