Mitsubishi QCPU Manual del propietario

A - 1

•SAFETY PRECAUTIONS •

(You must read these cautions before using the product)

As for the use of the product, please carefully read this manual and the related manuals introduced later.

Also, please pay attention to safety adequately and manage the product correctly.

The safety cautions shown in this manual apply to the product only.

In this manual, the safety precautions are ranked as "DANGER" and "CAUTION".

!DANGER

CAUTION

Indicates that incorrect handling may cause hazardous conditions,

resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous conditions,

resulting in medium or slight personal injury or physical damage.

Note that the !CAUTION level may lead to a serious consequence according to the circumstances.

Always follow the instructions of both levels because they are important to personal safety.

Please store this manual in order to read whenever it is necessary. Also, always forward this manual to

the end users.

[Design Precautions]

!DANGER

•Install a safety circuit external to the programmable controller that keeps the entire system safe

even when there are problems with the external power supply or the programmable controller.

Otherwise, it may cause an output error or an operating error, resulting in an accident.

(1) Configure a circuit such as an emergency stop circuit and a protective circuit on the outside

of the programmable logic controller.

(2) When the programmable controller detects the following problems, it will stop calculation

and turn off all outputs.

• An overcurrent protective device or an overvoltage protective device in a power supply

module start running.

• A watchdog timer error or others is detected with self-checking function in the

programmable controller CPU.

All outputs may be turned on, when an error occurs in the part of I/O controlling or others

that the programmable controller CPU cannot detect. Build a fail safe circuit exterior to the

programmable controller to keep the entire system safe.

As for the fail safe circuit, refer to a CPU module User’s Manual.

• Configure a circuit that turns on an external power supply when the main power of

programmable controller is turned on. If the external power supply is turned on first, it could

result in an output error or an operating error.

A - 2

[Design Precautions]

!DANGER

• When connecting a peripheral device to the CPU module or connecting a personal computer or

others to an intelligent function module, always configure an interlock circuit in the sequence

program to ensure that the whole system always operate safely.

Also, make sure to read this manual carefully and check all operations for safety first before

executing other control (program changes, changes of operation status (and status control)) of

the operating sequence.

Especially for the control described above on the remote sequence from an external device, an

immediate action may not be taken for a programmable controller’s trouble due to a data

communication fault.

Configure the interlock circuit in the sequence program. Simultaneously a recovery method for

system, in which a data communications fault occurs, should be determined between the

external device and the programmable controller CPU.

[Startup/Maintenance Precaution]

!CAUTION

• Make sure to read this manual carefully and check all operations for safety first before

connecting a peripheral device to an operating CPU module online (particularly program

changes, forced outputs, and changes of operation status). Otherwise, an operating error may

cause damage or problems with the modules.

A - 3

REVISIONS

* The manual number is given on the bottom left of the back cover.

Print Date * Manual Number Revision

Dec., 1999 SH (NA) 080040-A First edition

Jun., 2001 SH (NA) 080040-B Partial addition

About Manuals, Chapter 1, Chapter 2, Section 2.1, 3.1, 3.2, 3.3, 3.3.1,

4.2.3, 4.3.2, 4.3.5, Chapter 5, Section 5.1, 5.2, Chapter 6, Chapter 7,

Section 8.1, 8.2

Apr., 2002 SH (NA) 080040-C Correction

Chapter 1, Chapter 7, Section 8.1, 8.2, 8.3, 8.4, 8.5

Jan., 2003 SH (NA) 080040-D • Addition of use of Basic model QCPU

• Addition of explanation of incomplete derivative

Overall reexamination

Mar., 2003 SH (NA) 080040-E • Addition of explanation of incomplete derivative to High Performance

model QCPU

Dec., 2003 SH (NA) 080040-F Correction

Chapter 1

Jun., 2004 SH (NA) 080040-G Addition of Redundant CPU

Partial addition

About Manuals, Chapter 1, Chapter 2, Section 2.1, 3.1.1, 3.1.3, 3.2.1,

3.2.3, 4.3.5, 5.1, 5.2, Chapter 6, Chapter 7, Section 8.1.1 to 8.1.4,

Section 9.1.1 to 9.1.5, 9.2, Appendix 1

Sep., 2006 SH (NA) 080040-H Partial addition

Section 4.2.5, Appendix 2

Apr.,2007 SH (NA) 080040-I Addition of Universal model QCPU

Addition module

Q02UCPU, Q03UDCPU, Q04UDHCPU, Q06UDHCPU

Partial correction

GENERIC TERMS AND ABBREVIATIONS USED IN THIS MANUAL,

Chapter 1, Chapter 2, Section 2.1, 3.1.1, 3.1.3, 3.2.1, 3.2.3, 5.1, Chapter 6,

Chapter 7, 8.1.1 to 8.1.5, 9.1.1 to 9.1.5, Appendix 1

Mar.,2008 SH (NA) 080040-J Addition of Universal model QCPU

Addition module

Q13UDHCPU, Q26UDHCPU

Partial correction

GENERIC TERMS AND ABBREVIATIONS USED IN THIS MANUAL,

Section 2.1, Appendix 1

A - 4

* The manual number is given on the bottom left of the back cover.

Print Date * Manual Number Revision

May,2008 SH (NA) 080040-K Revision due to the addition of Process CPU and Universal model QCPU

Addition module

Q03UDECPU, Q04UDEHCPU, Q06UDEHCPU, Q13UDEHCPU,

Q26UDEHCPU

Q02PHCPU, Q06PHCPU

Partial correction

GENERIC TERMS AND ABBREVIATIONS USED IN THIS MANUAL,

Section 2.1, Appendix 1

Japanese Manual Version SH-080022-K

This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent licenses.

Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which

may occur as a result of using the contents noted in this manual.

A - 5

INTRODUCTION

Thank you for choosing the Mitsubishi MELSEC-Q/QnA Series of Programmable Logic Controllers.

Please read this manual carefully so that the equipment is used to its optimum. A copy of this manual should

be forwarded to the end User.

CONTENTS

SAFETY CAUTIONS ......................................................................................................................................A- 1

REVISIONS .....................................................................................................................................................A- 3

CONTENTS.....................................................................................................................................................A- 5

About Manuals ................................................................................................................................................A- 8

Generic Terms and Abbreviations Used in This Manual ..............................................................................A-11

1. GENERAL DESCRIPTION 1 – 1 to 1 - 3

1.1 PID Processing Method ........................................................................................................................... 1 - 3

2. SYSTEM CONFIGURATION FOR PID CONTROL 2 - 1 to 2 - 2

2.1 Applicable PLC CPU................................................................................................................................ 2 - 2

3. PID CONTROL SPECIFICATIONS 3 - 1 to 3 - 14

3.1 PID Control by Incomplete derivative ...................................................................................................... 3 - 1

3.1.1 Performance specifications............................................................................................................... 3 - 1

3.1.2 PID operation block diagram and operation expressions ................................................................ 3 - 2

3.1.3 PID control instruction list.................................................................................................................. 3 - 3

3.2 PID Control by Complete Derivative........................................................................................................ 3 - 8

3.2.1 Performance specifications............................................................................................................... 3 - 8

3.2.2 PID operation block diagram and operation expressions ................................................................ 3 - 9

3.2.3 PID control instruction list................................................................................................................ 3 - 10

4. FUNCTIONS OF PID CONTROL 4 - 1 to 4 - 14

4.1 Outline of PID Control .............................................................................................................................. 4 - 1

4.2 Functions of PID Control.......................................................................................................................... 4 - 2

4.2.1 Operation method.............................................................................................................................. 4 - 2

4.2.2 Forward operation and reverse operation ........................................................................................ 4 - 2

4.2.3 Proportionate operation (P operation) .............................................................................................. 4 - 4

4.2.4 Integrating operation (I operation) .................................................................................................... 4 - 5

4.2.5 Differentiating operation (D operation) ............................................................................................. 4 - 6

4.2.6 PID operation..................................................................................................................................... 4 - 8

4.3 Other Functions........................................................................................................................................ 4 - 9

4.3.1 Bumpless changeover function ........................................................................................................ 4 - 9

4.3.2 MV higher/lower limit control function............................................................................................. 4 - 10

4.3.3 Monitorning PID control with the AD57(S1) (QnACPU only)......................................................... 4 - 11

4.3.4 Function for transfer to the SV storage device for the PV in manual mode.................................. 4 - 12

4.3.5 Changing the PID control data or input/output data setting range (QCPU only) ......................... 4 – 13

A - 6

5. PID CONTROL PROCEDURE 5 - 1 to 5 - 24

5.1 PID Control Data ...................................................................................................................................... 5 - 4

5.1.1 Number of loops to be used and the number of loops to be executed in a single scan............... 5 - 15

5.1.2 Sampling cycle ................................................................................................................................ 5 - 16

5.2 I/O Data .................................................................................................................................................. 5 - 18

6. PID CONTROL INSTRUCTIONS 6 - 1 to 6 - 2

7. HOW TO READ EXPLANATIONS FOR INSTRUCTIONS 7 - 1 to 7 - 2

8. INCOMPLETE DERIVATIVE PID CONTROL INSTRUCTIONS AND PROGRAM EXAMPLES

8 - 1 to 8 - 16

8.1 PID Control Instructions ........................................................................................................................... 8 - 1

8.1.1 PID control data settings S.PIDINIT,SP.PIDINIT .......................................... 8 - 2

8.1.2 PID operation S.PIDCONT,SP.PIDCONT................................... 8 - 3

8.1.3 Operation stop/start of designated loop no. S.PIDSTOP,SP.PIDSTOP,S.PIDRUN,SP.PIDRUN

.................................................................................................................................................................... 8 - 5

8.1.4 Parameter change at designated loop S.PIDPRMW,SP.PIDPRMW ................................ 8 - 6

8.2 PID Control Program Examples .............................................................................................................. 8 - 8

8.2.1 System configuration for program examples.................................................................................... 8 - 8

8.2.2 Program example for automatic mode PID control.......................................................................... 8 - 9

8.2.3 Program example for changing the PID control mode between automatic and manual .............. 8 - 13

9. COMPLETE DERIVATIVE PID CONTROL INSTRUCTIONS AND PROGRAM EXAMPLES 9 - 1 to 9 - 28

9.1 PID Control Instructions ...........................................................................................................................9 - 1

9.1.1 PID control data settings PIDINIT,PIDINITP................................................. 9 - 2

9.1.2 PID control PIDCONT,PIDCONTP.......................................... 9 - 3

9.1.3 Monitoring PID control status (QnACPU only) PID57,PID57P....................................................... 9 - 5

9.1.4 Operation stop/start of designated loop no. PIDSTOP,PIDSTOPP,PIDRUN,PIDRUNP ......... 9 - 8

9.1.5 Parameter change at designated loop PIDPRMW,PIDPRMWP ....................................... 9 - 9

9.2 PID Control Program Examples (QCPU only) ...................................................................................... 9 - 11

9.2.1 System configuration for program examples.................................................................................. 9 - 11

9.2.2 Program example for automatic mode PID control........................................................................ 9 - 12

9.2.3 Program example for changing the PID control mode between automatic and manual .............. 9 - 15

9.3 PID Control Program Examples (QnACPU only).................................................................................. 9 - 19

9.3.1 System configuration for program examples.................................................................................. 9 - 19

9.3.2 Program example for automatic mode PID control........................................................................ 9 - 20

9.3.3 Program example for changing the PID control mode between automatic and manual ............. 9 – 24

A - 7

APPENDIX APP - 1 to APP - 3

Appendix 1 Processing Time List .............................................................................................................APP - 1

Appendix 2 Anti-Reset Windup Measure .................................................................................................APP - 3

A - 8

About Manuals

The following manuals are also related to this product.

In necessary, order them by quoting the details in the tables below.

Related Manuals

Manual Name Manual Number

(Model Code)

QCPU User's Manual (Function Explanation, Program Fundamentals)

Describes the functions, programming procedures, devices, etc. necessary to create programs.

(Sold separately)

SH-080484ENG

(13JR73)

QnACPU Programming Manual (Fundamentals)

Describes how to create programs, the names of devices, parameters, and types of program.

(Sold separately)

IB-66614

(13JF46)

QCPU (Q mode) /QnACPU Programming Manual (Common Instructions)

Describes how to use sequence instructions, basic instructions, and application instructions.

(Sold separately)

SH-080039

(13JF58)

QnACPU Programming Manual (Special Function)

Describes the dedicated instructions for special function modules available when using the

Q2ACPU(S1), Q3ACPU, and Q4ACPU. (Sold separately)

SH-4013

(13JF56)

QnACPU Programming Manual (AD57 Instructions)

Describes the dedicated instructions for controlling an AD57(S1) type CRT controller module available

when using the Q2ACPU(S1), Q3ACPU, or Q4ACPU. (Sold separately)

IB-66617

(13JF49)

Otros manuales para QCPU

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Controladores de Mitsubishi

Mitsubishi

Mitsubishi MELSEC Q Series Manual de usuario

Mitsubishi

Mitsubishi FX3U-64CCL Manual de usuario

Mitsubishi

Mitsubishi FX1S Series Manual de usuario

Mitsubishi

Mitsubishi MELSEC-F FX3U-4AD Manual de usuario

Mitsubishi

Mitsubishi MELSEC-F FX3U-4AD-ADP Manual de usuario

Mitsubishi

Mitsubishi CR800 Series Manual de usuario

Mitsubishi

Mitsubishi MELSEC-A series Manual de usuario

Mitsubishi

Mitsubishi MELSEC Q Series Manual de usuario

Mitsubishi

Mitsubishi L02CPU Manual de usuario

Mitsubishi

Mitsubishi FX3U Series Manual del propietario

Mitsubishi

Mitsubishi FX2N-4AD-PT Manual de usuario

Mitsubishi

Mitsubishi FX2N-4AD-PT Manual de usuario

Mitsubishi

Mitsubishi AL2-14MR-A Manual de usuario

Mitsubishi

Mitsubishi melservo-j2 series Manual de usuario

Mitsubishi

Mitsubishi MELSEC QJ71C24N Manual de usuario

Mitsubishi

Mitsubishi MELSEC-A A1SCPUC24-R2 Manual de usuario

Mitsubishi

Mitsubishi QD75P1N Manual de usuario

Mitsubishi

Mitsubishi Q01CPU Manual de usuario

Mitsubishi

Mitsubishi FX3U Series Manual de usuario

Mitsubishi

Mitsubishi AJ65BT-D62 Manual de usuario

Mitsubishi

Mitsubishi FX2N-10GM Manual de usuario

Mitsubishi

Mitsubishi AG-150A Manual de usuario

Mitsubishi

Mitsubishi MELSEC-A AJ71E71-S3 Manual de usuario

Mitsubishi

Mitsubishi FX2N Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario