Mitsubishi FX1S Series Manual de usuario

HARDWARE MANUAL

FX1S SERIES PROGRAMMABLE CONTROLLERS

FX1S Series Programmable Controllers

Foreword

• This manual contains text, diagrams and explanations which will guide the reader in the correct installation

and operation of the FX1S Series Programmable Controllers. It should be read and understood before

attempting to install or use the unit.

• Further information can be found in the FX Series Programming Manual II.

• If in doubt at any stage of the installation of an FX1S Series Programmable Controller always consult a

professional electrical engineer who is qualified and trained to the local and national standards which apply to

the installation site.

• If in doubt about the operation or use of FX1S Series Programmable Controller please consult the nearest

Mitsubishi Electric distributor.

• This manual is subject to change without notice.

FX1S Series Programmable Controllers

Hardware Manual

FX1S Series Programmable Controllers

Manual number : JY992D83901

Manual revision : H

Date : January 2004

FX1S Series Programmable Controllers

Guidelines for the Safety of the User and Protection of the FX1S.

This manual provides information for the use of the FX1S. The manual has been written to be

used by trained and competent personnel. The definition of such a person or persons is as

follows:

a) Any engineer who is responsible for the planning, design and construction of automatic

equipment using the product associated with this manual, should be of a competent

nature, trained and qualified to the local and national standards required to fulfill that

role. These engineers should be fully aware of all aspects of safety with regards to

automated equipment.

b) Any commissioning or service engineer must be of a competent nature, trained and

qualified to the local and national standards required to fulfill that job. These engineers

should also be trained in the use and maintenance of the completed product. This

includes being completely familiar with all associated documentation for said product. All

maintenance should be carried out in accordance with established safety practices.

c) All operators of the completed equipment (see Note) should be trained to use this

product in a safe manner in compliance to established safety practices. The operators

should also be familiar with documentation which is associated with the operation of the

completed equipment.

Note : The term ‘completed equipment’refers to a third party constructed device which

contains or uses the product associated with this manual.

FX1S Series Programmable Controllers

iii

Notes on the Symbols Used in this Manual

At various times throughout this manual certain symbols will be used to highlight points which

are intended to ensure the users personal safety and protect the integrity of equipment.

Whenever any of the following symbols are encountered its associated note must be read and

understood. Each of the symbols used will now be listed with a brief description of its meaning.

Hardware Warnings

1) Indicates that the identified danger WILL cause physical and property damage.

2) Indicates that the identified danger could POSSIBLY cause physical and property

damage.

3) Indicates a point of further interest or further explanation.

Software Warnings

4) Indicates special care must be taken when using this element of software.

5) Indicates a special point which the user of the associate software element should

be aware.

6) Indicates a point of interest or further explanation.

FX1S Series Programmable Controllers

•Under no circumstances will Mitsubishi Electric be liable responsible for any consequential

damage that may arise as a result of the installation or use of this equipment.

•All examples and diagrams shown in this manual are intended only as an aid to

understanding the text, not to guarantee operation. Mitsubishi Electric will accept no

responsibility for actual use of the product based on these illustrative examples.

•Please contact a Mitsubishi Electric distributor for more information concerning applications

in life critical situations or high reliability.

FX1S Series Programmable Controllers

Note Concerning the CE Marking

This note does not guarantee that an entire mechanical module produced in accordance with

the contents of this note will comply with the following standards. Compliance to EMC directive

and LVD directive of the entire mechanical module should be checked by the user /

manufacturer. For more details please contact the local Mitsubishi Electric sales site.

EMC

The following products have shown compliance through direct testing (of the identified

standards below) and design analysis (through the creation of a technical construction file) to

the European Directive for Electromagnetic Compatibility (89/336/EEC) when used as directed

by the appropriate documentation.

Refer to a manual or related material of each product for details concerning products not

included below.

Type: Programmable Controller (Open Type Equipment)

Models : MELSEC FX1S series manufactured

from March 1st, 2000 FX1S-!!MR-ES/UL

from September 1st, 2000 FX1S-!!MR-DS FX1S-!!MT-DSS

from July 1st, 2001 FX1S-!!MT-ESS/UL

Where !! indicates:10,14,20,30

Models : MELSEC FX1N series manufactured

from March 1st, 2000 FX1N-232-BD FX1N-485-BD FX1N-422-BD

FX1N-8AV-BD FX1N-5DM FX1N-EEPROM-8L

FX1N-CNV-BD

FX1S Series Programmable Controllers

from June 1st, 2001 FX1N-4EX-BD FX1N-2EYT-BD FX1N-2AD-BD

FX1N-1DA-BD

Models : MELSEC FX0N series manufactured

from May 1st, 1996 FX0N-232ADP FX0N-485ADP

Models : MELSEC FX2NC series manufactured

from October 1st, 2002 FX2NC-232ADP FX2NC-485ADP

Standard Remark

EN50081-2:1993 Electromagnetic compatibility

EN61000-6-4:2001 - Generic emission standard

Industrial environment

Compliance with all relevant aspects of the

standard.

(Radiated Emissions and Mains Terminal Voltage

Emissions)

EN61000-6-2:2001 Electromagnetic compatibility

- Generic immunity standard

Industrial environment

Compliance with all relevant aspects of the

standard.

(RF immunity,Fast Transients,ESD,Conducted,

Surge,Power magnetic fields,Voltage dips and

Voltage interruptions)

FX1S Series Programmable Controllers

vii

LV D

The following products have shown compliance through direct testing (of the identified

standards below) and design analysis (through the creation of a technical construction file) to

the European Directive for Low Voltage (73/23/EEC) when used as directed by the appropriate

documentation.

Refer to a manual or related material of each product for details concerning products not

included below.

Type : Programmable Controller (Open Type Equipment)

Models : MELSEC FX1S series manufactured

from March 1st, 2000 FX1S-!!MR-ES/UL

from September 1st, 2000 FX1S-!!MR-DS

from July 1st, 2001 FX1S-!!MT-ESS/UL

Where !! indicates:10,14,20,30

Standard Remark

EN61010-1:2001 Safety requirements for electrical

equipment for measurement,

control,and laboratory use

- General requirements

The equipment has been assessed as

a component for fitting in a suitable enclosure

which meets the requirements of

EN61010-1:2001

FX1S Series Programmable Controllers

viii

Associated Manuals

The following manuals are recommended as essential reference material for the correct operation of a

FX1S series Programmable controller.

Manual Name Manual Number Description

FX Programming Manual II JY992D88101 This manual contains instruction explanation about

FX1S, FX1N, FX2N and FX2NC Series PLC.

FX Communication

User’s Manual JY992D69901

This manual contains explanation for N:N network,

parallel link, no protocol communication and

computer link

FX1N-5DM User’s Manual JY992D84901 This manual contains hardware explanation for

installation, specification and operation.

FX-10DM-E User’s Manual JY992D86401 This manual contains hardware explanation for

installation, specification and operation.

FX1N-422-BD

Users Manual JY992D84101 This manual contains hardware explanation for

installation and specification.

FX1N-485-BD

Users Manual JY992D84201 This manual contains hardware explanation for

installation and specification.

FX1N-232-BD

Users Manual JY992D84401 This manual contains hardware explanation for

installation and specification.

FX1N-4EX-BD

Users Manual JY992D95001 This manual contains explanation for installation,

specification and special auxiliary relay allocation.

FX1N-2EYT-BD

Users Manual JY992D95201 This manual contains explanation for installation,

specification and special auxiliary relay allocation.

Otros manuales para FX1S Series

Tabla de contenidos

Otros manuales de Controladores de Mitsubishi

Mitsubishi

Mitsubishi MELSEC Q Series Manual de usuario

Mitsubishi

Mitsubishi MELSEC-L Series Manual de usuario

Mitsubishi

Mitsubishi MELSEC-QnA Series Manual de usuario

Mitsubishi

Mitsubishi QD60P8-G Manual de usuario

Mitsubishi

Mitsubishi MELSEC-L Series Manual de usuario

Mitsubishi

Mitsubishi Q00JCPU Manual de usuario

Mitsubishi

Mitsubishi FX3U-?*MR/ES Manual de usuario

Mitsubishi

Mitsubishi MELSEC-F FX3U-4AD-TC-ADP Manual de usuario

Mitsubishi

Mitsubishi FX2N-ROM-E1 Manual de usuario

Mitsubishi

Mitsubishi Q68TD-G-H01 Manual de usuario

Mitsubishi

Mitsubishi FX2N-10GM Manual del propietario

Mitsubishi

Mitsubishi AL2 Series Manual del propietario

Mitsubishi

Mitsubishi MELSEC-A AJ71PT3 Manual de usuario

Mitsubishi

Mitsubishi MELSEC Q Series Manual de usuario

Mitsubishi

Mitsubishi MELSEC Q Series Manual de usuario

Mitsubishi

Mitsubishi MELSEC Q Series Manual de usuario

Mitsubishi

Mitsubishi MELSEC-F FX3U-4AD-ADP Manual de usuario

Mitsubishi

Mitsubishi MELSEC Q Series Manual de usuario

Mitsubishi

Mitsubishi FX-10P-E Manual de instalación

Mitsubishi

Mitsubishi L02CPU Manual de usuario

Mitsubishi

Mitsubishi QJ71E71-100 Series Manual de usuario

Mitsubishi

Mitsubishi MELSEC Q Series Manual de usuario

Mitsubishi

Mitsubishi FX3U Series Manual de usuario

Mitsubishi

Mitsubishi Q12PRHCPU Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario