Mitsubishi A1SJ61BT11 Manual de usuario

Control & Communication Link System Master/Local Module

Type AJ61BT11/A1SJ61BT11 User,s Manual

Mitsubishi Programmable Controller

A - 1

•SAFETY PRECAUTIONS •

(Read these precautions before using.)

When using Mitsubishi equipment, thoroughly read this manual and the associated manuals introduced in

this manual.

Also pay careful attention to safety and handle the module properly. These precautions apply only to

Mitsubishi equipment. Refer to the user’s manual of the CPU module to use for a description of the PLC

system safety precautions.

These •SAFETY PRECAUTIONS •classify the safety precautions into two categories: "DANGER" and

"CAUTION".

DANGER

CAUTION

Procedures which may lead to a dangerous condition and cause death

or serious injury if not carried out properly.

Procedures which may lead to a dangerous condition and cause

superficial to medium injury, or physical damage only, if not carried out

properly.

Depending on circumstances, procedures indicated by !CAUTION may also be linked to serious

results.

In any case, it is important to follow the directions for usage.

Store this manual in a safe place so that you can take it out and read it whenever necessary. Always

forward it to the end user.

[DESIGN PRECAUTIONS]

!DANGER

•Read Chapter 5 in this manual carefully for status of each station when the PC CPU has

stopped its operation and when a communication error occurred in the data link.

Configure an interlocking circuit in a sequence program using the communication status

information (SB, SW) so that the safety of the overall system is always maintained.

Accident may occur due to output error or malfunctioning.

•An error is not detected by the master station nor local station when a station specified as an

error-invalid station is in a communication error status.

!CAUTION

•Do not bundle, on install, the control cables and communication cables with, or near, main circuit

and power cables. Keep them at least 100mm (3.9 inch) away from such cables. Noise may

cause erroneous operation.

A - 2

[INSTALLATION PRECAUTIONS]

!CAUTION

•Use the PC in the environment given in the general specifications section of this manual. Using

the PC outside the range of the general specifications may result in electric shock, fire, or

erroneous operation or may damage or degrade the product.

•Insert the tabs at the bottom of the module into the holes in the base unit before installing the

module. (Modules in AnS series, make sure screws are securely tightened to base unit with

specified torques.)

Improper installation may cause erroneous operation, accidents, or the module to fall out.

•Do not directly touch the module's conductive parts or electronic components.

Doing so could cause malfunction or trouble in the module.

[PRECAUTIONS REGARDING WIRING]

!DANGER

•Completely turn off the external power supply when installing or placing wiring. Failing to

completely shut out the power supply phases could cause electrical shock and/or damage to the

product.

•Following installation or wiring work, when turning on the power supply and operating the

equipment, make sure the terminal cover provided as an accessory has been attached to the

product.

[WIRING PRECAUTIONS]

!CAUTION

•Tighten the terminal screws by the specified torque.

Loose terminal screws may cause a short circuit or erroneous operation.

Overtightening of screws can cause damages to the screws and/or the module, resulting in

fallout, short circuits, or malfunction.

•Be sure that cuttings, wire chips, or other foreign matter do not enter the module.

Foreign matter may start a fire or cause an accident or erroneous operation.

•Be sure to fix the wires or cables by ducts or clamps when connecting them to the module.

Cables not placed in the duct or without clamping may hang or shift, allowing them to be

accidentally pulled, which may result in a malfunction or damage to the module and cable.

•Do not install the control lines together with the communication cables, or bring them close to

each other. Failure to do so may cause malfunctions due to noise.

•When detaching the communication cable or power cable from the module, do not pull the cable

portion. For cables with connectors, hold the connector at the junction to the module, then

detach it. For connectors without connectors, first loosen the screw at the junction, then detach

the cable.

Pulling the cable portion while it is connected to the module may cause a malfunction or damage

to the module and cable.

A - 3

[STARTING AND MAINTENANCE PRECAUTIONS]

!CAUTION

•Do not touch any terminal without turning off all phases of the external power supply used in the

system.

It may cause erroneous operation.

•Be sure to shut off all phases of the external power supply before cleaning or retightening the

terminal screws. Doing this work while the power is on may damage the module or cause

erroneous operation.

•Do not disassemble or rebuild the module.

It may cause accidents, erroneous operation, injury, or fire.

•Be sure to shut off all phases of the external power supply used by the system before mounting

or removing the module.

Mounting or dismounting the module whhile the power is on may damage the module or cause

erroneous operation.

•Do not mount/remove the module onto/from base unit more than 50 times

(IEC61131-2-compliant), after the first use of the product.

•Always make sure to touch the grounded metal to discharge the electricity charged in the

electricity charged in the body, etc., before touching the module.

Failure to do say cause a failure or malfunctions of the module.

[DISPOSAL PRECAUTIONS]

!CAUTION

•When disposing of this product, handle it as industrial waste.

A - 4

Revisions

The manual number is noted at the lower left of the back cover.

Print Date Manual Number Revision

Nov. 1996 IB (NA)-66721-A First printing

Jan. 1997 IB (NA)-66721-B Addition

Section 3.2.1, 4.12.3, 13.2

Correction

Chapter 1, Section 1.1, 3.2, 3.4.1, 7.3, 7.6.3, 8.3.2, 13.1, 13.5.8

Aug. 1997 IB (NA)-66721-C Addition

Section 1.1, 5.3.4, 5.4, Chapter 14, 15, 16

Correction

Section 1.4, 1.5, 2.1, 2.2.1, 2.2.3, 3.2, 3.2.1, 3.4.1, 3.4.2, 5.1, 7.1, 7.2.1,

7.3, 7.5, 7.6.1, 7.6.3, 7.6.4, 7.7.1, 7.7.2, 7.8

Jan. 1998 IB (NA)-66721-D Addition model

Section 1.4, 2.2.3

Correction

Section 1.1, 3.3, 3.4.1, 3.5.1, 3.5.2, 4.3, 4.5, 5.2, 7.6.4, 13.1, Chapter

14, 15.1, 15.2.1, 15.6, 15.6.1, 15.6.3, 15.6.4, 15.6.5, 15.6.10, 16.2.3,

App2

Mar. 2000 IB (NA)-66721-E Addition model

Section 2.2.3

Addition

Section 7.6, 15.7

Correction

SAFETY PRECAUTIONS, Section 1.1, 1.5, 3.3, 3.5.1, 5.1, 5.2, 5.4.3,

7.3, 7.5, 8.3.2, 10.2.2, 12.2.2, 13.3, Chapter 14, Section 15.1, 15.2.1,

15.5.2, 15.5.4, 15.5.5, 15.6, 15.8, Chapter 16

Jul. 2000 IB (NA)-66721-F Addition

Section 2.2.4, 3.2.2

Correction

Section 1.4, 2.2.1, 3.2, 3.2.1, 3.3, 3.4.2, 3.5.1, 7.3, 7.6.2, 7.7.4, 8.3.1,

9.1.1, 10.1.1, 10.2.2, 11.1.1, 11.1.2, 12.1.1, 12.1.4, 15.2.1, App1.1,

App1.2

Jul. 2001 IB (NA)-66721-G Addition

Section 8.2

Correction

Section 2.2.3, 3.4.1, 3.4.2, 4.12.1, 5.4, 5.4.1, 5.4.2, 5.4.3, 7.2.1, 7.3, 7.5,

8.4.2, 9.1.1, 9.2.1, 10.1.1, 10.2.1, 11.1.1, 11.1.2, 11.2.1, 12.1.1, 12.1.4,

12.2.1, 13.1, 13.3, 13.4.2, 13.4.3, Chapter 14, Section 15.1, 15.2.1, 15.6,

15.7.1

A - 5

The manual number is noted at the lower left of the back cover.

Print Date Manual Number Revision

Jul. 2002 IB (NA)-66721-H Correction

Section 2.2.3, 3.3, 3.4.2, 4.10, 8.1, 13.3, 15.6

Oct. 2002 IB (NA)-66721-I Correction

Section 3.1, 3.5.2

Oct. 2003 IB (NA)-66721-J Addition

Conformation to the EMC Directive and Low Voltage Instruction

Correction

SAFETY PRECAUTIONS, Section 3.5.1, 7.8, 7.9, 13.3

Apr. 2006 IB (NA)-66721-K Correction

SAFETY PRECAUTIONS, Conformation to the EMC Directive and Low

Voltage Instruction , Chapter 1, Section 2.2.2, 2.2.4, 3.2, 3.4.1, 3.4.2, 4.1,

4.8, 6.3, 7.5, 13.1, 13.3, 15.2.1, App2

Sep. 2007 IB (NA)-66721-L Correction

Section 1.4, 1.5, 2.1, 2.2.3, 3.5.2, 4.4, 7.3, 7.7.4, 8.4.1, App1.2

Japanese Manual Version SH-3603-L

This manual does not imply guarantee or implementation right for industrial ownership or implementation of other rights.

Mitsubishi Electric Corporation is not responsible for industrial ownership problems caused by use of the contents of this

manual.

A - 6

INTRODUCTION

Thank you for choosing a Mitsubishi MELSEC-A Series General Purpose Programmable Controller.

Before using your new PC, please read this manual thoroughly to gain an understanding of its functions so you

can use it properly.

Please forward a copy of this manual to the end user.

Table of Contents

SAFETY PRECAUTIONS..............................................................................................................................A- 1

Revisions ........................................................................................................................................................A- 4

INTRODUCTION............................................................................................................................................A- 6

About This Manual .........................................................................................................................................A-12

Conformation to the EMC Directive and Low Voltage Instruction ................................................................A-12

1. Overview..........................................................................................................................................1- 1 to 1-14

1.1 How to Use This Manual......................................................................................................................... 1- 3

1.2 Characteristics......................................................................................................................................... 1- 4

1.3 Communication Overview....................................................................................................................... 1- 9

1.3.1 Communication between the master station and remote I/O station ............................................. 1- 9

1.3.2 Communication between the master station and remote device station ....................................... 1-10

1.3.3 Communication between the master station and local station ....................................................... 1-11

1.3.4 Compound system communication ................................................................................................. 1-12

1.4 Number of Occupied Stations and Station Number, Number of Unit and Number of Stations............ 1-13

1.5 Abbreviations and Special Terms........................................................................................................... 1-14

2. System Configuration......................................................................................................................2- 1 to 2- 8

2.1 Total Configuration.................................................................................................................................. 2- 1

2.2 Applicable System .................................................................................................................................. 2- 2

2.2.1 Applicable CPU and number of cards that can be installed ........................................................... 2- 2

2.2.2 Precautions when configuring a system.......................................................................................... 2- 3

2.2.3 List of system equipment restricted by master/local module versions ........................................... 2- 6

2.2.4 About Ver. 1.10................................................................................................................................. 2- 7

3. Specification ....................................................................................................................................3- 1 to 3-36

3.1 General Specification.............................................................................................................................. 3- 1

3.2 Performance Specifications .................................................................................................................... 3- 2

3.2.1 Maximum overall cable distance (for Ver. 1.00).............................................................................. 3- 3

3.2.2 Maximum overall cable distance (for Ver. 1.10).............................................................................. 3- 5

3.3 CC-Link Dedicated Cable ....................................................................................................................... 3- 6

3.4 I/O Signals to the PC CPU...................................................................................................................... 3- 7

3.4.1 I/O signal list ..................................................................................................................................... 3- 7

3.4.2 I/O signal details ............................................................................................................................... 3- 9

3.5 Buffer Memory......................................................................................................................................... 3-18

3.5.1 Buffer memory list ............................................................................................................................ 3-18

3.5.2 Buffer memory details ...................................................................................................................... 3-20

A - 7

4. Functions .........................................................................................................................................4- 1 to 4-30

4.1 Function List ............................................................................................................................................ 4- 1

4.2 Communication Between the Master Station and Remote I/O Station ................................................. 4- 2

4.3 Communication Between the Master Station and Remote Device Station........................................... 4- 4

4.4 Communication Between the Master Station and Local Station ........................................................... 4-10

4.5 Communication in Compound Systems................................................................................................. 4-16

4.6 Reserved Station Function ..................................................................................................................... 4-22

4.7 Error Invalid Station Function ................................................................................................................. 4-23

4.8 Data Link Status Setting when the Master Station PC CPU has an Error ............................................ 4-24

4.9 Setting the Status of Input Data from a Data Link Faulty Station.......................................................... 4-25

4.10 Module Reset Function from a Sequence Program ............................................................................ 4-26

4.11 Data Link Stop/Restart.......................................................................................................................... 4-27

4.12 RAS Function ........................................................................................................................................ 4-28

4.12.1 Automatic return function ............................................................................................................... 4-28

4.12.2 Slave station cut-off function.......................................................................................................... 4-29

4.12.3 Station number overlap checking function .................................................................................... 4-30

5. Data Link Processing Time .............................................................................................................5- 1 to 5-24

5.1 Status of Each Station when an Error has Occurred............................................................................. 5- 1

5.2 Link Scan Time ....................................................................................................................................... 5- 4

5.3 Transmission Delay Time ....................................................................................................................... 5- 5

5.3.1 Master station remote I/O station................................................................................................ 5- 5

5.3.2 Master station remote device station .......................................................................................... 5- 7

5.3.3 Master station local station.......................................................................................................... 5-11

5.3.4 Master station intelligent device station ...................................................................................... 5-15

5.4 Dedicated Instruction Processing Time.................................................................................................. 5-16

5.4.1 Master station local station ......................................................................................................... 5-16

5.4.2 Local station local station............................................................................................................ 5-20

5.4.3 Master station intelligent device station ..................................................................................... 5-22

6. Parameter Setting ...........................................................................................................................6- 1 to 6-10

6.1 Procedure from Parameter Setting to Data Link Startup....................................................................... 6- 1

6.1.1 Relationship between buffer memory, E2PROM and internal memory.......................................... 6- 1

6.1.2 Procedure from parameter setting to data link start........................................................................ 6- 3

6.2 Parameter Settings ................................................................................................................................. 6- 4

6.3 Setting from a Sequence Program ......................................................................................................... 6- 5

A - 8

7. Data Link Procedure........................................................................................................................7- 1 to 7-22

7.1 Data Link Procedure ............................................................................................................................... 7- 1

7.2 Installation and Setting............................................................................................................................ 7- 2

7.2.1 Precautions when handling the module .......................................................................................... 7- 2

7.2.2 Setting environment ......................................................................................................................... 7- 2

7.3 Name of Each Part and Settings ............................................................................................................ 7- 3

7.4 Checking Module Condition (Hardware Test)........................................................................................ 7- 7

7.5 Module Wiring with CC-Link Dedicated Cable ....................................................................................... 7- 9

7.6 T-Branch Connection with the CC-Link Dedicated Cable ..................................................................... 7-10

7.6.1 T-Branch system configuration ........................................................................................................ 7-10

7.6.2 T-Branch communication specifications list .................................................................................... 7-10

7.7 Switch Settings........................................................................................................................................ 7-12

7.7.1 Station number setting (master station, local station and remote station) ..................................... 7-12

7.7.2 Mode setting ..................................................................................................................................... 7-14

7.7.3 Transmission speed setting ............................................................................................................. 7-14

7.7.4 Condition setting............................................................................................................................... 7-15

7.8 Checking the Connection Condition (Line Test) .................................................................................... 7-16

7.8.1 Checking connection and communication status with remote station/local station

(Line Test 1)...................................................................................................................................... 7-16

7.8.2 Checking connection and communication status with specific remote

station/local station (Line Test 2) ..................................................................................................... 7-18

7.9 Checking Parameters (Parameter Confirmation Test) ..........................................................................7-20

8. Programming ...................................................................................................................................8- 1 to 8-22

8.1 Precautions when Programming ............................................................................................................ 8- 1

8.2 Precautions for Registering Parameters to E2PROM............................................................................. 8- 3

8.2.1 Target module and versions ............................................................................................................ 8- 3

8.2.2 Precautions....................................................................................................................................... 8- 3

8.2.3 Program for registering parameters to E2PROM ............................................................................ 8- 4

8.3 Programming Procedure........................................................................................................................ 8- 6

8.3.1 Communication between the master station and remote I/O station ............................................. 8- 6

8.3.2 Communication between the master station and remote device station ....................................... 8- 7

8.3.3 Communication between the master station and local station ....................................................... 8- 8

8.3.4 Communication in a compound system .......................................................................................... 8-10

8.4 Link Special Relay/Register (SB/SW) .................................................................................................... 8-12

8.4.1 Link special relay (SB) ..................................................................................................................... 8-12

8.4.2 Link special register (SW) ................................................................................................................ 8-16

9. Communication Between the Master Station and the Remote I/O Station ...................................9- 1 to 9-12

9.1 System Configuration.............................................................................................................................. 9- 1

9.1.1 Setting of the master station ............................................................................................................ 9- 2

9.1.2 Setting of the remote I/O station ...................................................................................................... 9- 3

9.2 Creating a Program................................................................................................................................. 9- 4

9.2.1 Program for parameters ................................................................................................................... 9- 4

9.2.2 Communication program.................................................................................................................. 9- 7

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Controladores de Mitsubishi

Mitsubishi

Mitsubishi FX2N-32DP-IF Manual de usuario

Mitsubishi

Mitsubishi Q173DSXY Manual de usuario

Mitsubishi

Mitsubishi Q2ASCPU Manual de usuario

Mitsubishi

Mitsubishi AG-150A Manual de usuario

Mitsubishi

Mitsubishi MELSEC iQ-F FX5 series Manual del propietario

Mitsubishi

Mitsubishi Q172CPU Manual de usuario

Mitsubishi

Mitsubishi MELSEC Q Series Manual de usuario

Mitsubishi

Mitsubishi FX3G-4EX-BD Manual de usuario

Mitsubishi

Mitsubishi FX1N-485-BD Manual de usuario

Mitsubishi

Mitsubishi MELSEC-A series Manual del propietario

Mitsubishi

Mitsubishi MELSEC-Q/L Manual del propietario

Mitsubishi

Mitsubishi FX3U-32DP Manual de usuario

Mitsubishi

Mitsubishi MELSEC Q Series Manual del propietario

Mitsubishi

Mitsubishi L02CPU Manual de usuario

Mitsubishi

Mitsubishi MELSEC QS Series Manual de usuario

Mitsubishi

Mitsubishi Q01CPU Manual de usuario

Mitsubishi

Mitsubishi MELSEC-AnS Series Manual de usuario

Mitsubishi

Mitsubishi A Instrucciones de montaje

Mitsubishi

Mitsubishi FX2N-2LC Manual de usuario

Mitsubishi

Mitsubishi MELSEC QCPU Manual del propietario

Mitsubishi

Mitsubishi MELSEC F2-60MR Manual de usuario

Mitsubishi

Mitsubishi Q00JCPU Manual de usuario

Mitsubishi

Mitsubishi Q170MCPU Manual de usuario

Mitsubishi

Mitsubishi MELSEC-A series Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario