Mitsubishi Electric FR-A5AX Manual de usuario
TRANSISTORIZED INVERTER
-INSTRUCTION MANUAL-
IB(NA)-66808-B (0201) MEE
TRANSISTORIZED INVERTER
Printed in Japan Specifications subject to change without notice.
HEAD OFFICE:MITSUBISHI DENKI BLDG MARUNOUCHI TOKYO 100-8310 FR-A5AX
12-BIT DIGITAL INPUT
ib66808b.book 1 ページ ２００２年２月１４日 木曜日 午後７時５８分
A-1
Thank you for choosing the Mitsubishi transistorized inverter option unit.
This instruction manual gives handling information and precautions for use of this equipment. Incorrect handling
might cause an unexpected fault. Before using the equipment, please read this manual carefully to use the equipment
to its optimum.
Please forward this manual to the end user.
1. Electric Shock Prevention
This section is specifically about safety matters
Do not attempt to install, operate, maintain or inspect this product until you have read through this instruction man-
ual and appended documents carefully and can use the equipment correctly. Do not use this product until you have
a full knowledge of the equipment, safety information and instructions.
In this instruction manual, the safety instruction levels are classified into "WARNING" and "CAUTION".
Assumes that incorrect handling may cause hazardous conditions, resulting in
death or severe injury.
Assumes that incorrect handling may cause hazardous conditions, resulting in
medium or slight injury, or may cause physical damage only.
Note that the CAUTION level may lead to a serious consequence according to conditions. Please follow the instruc-
tions of both levels because they are important to personnel safety.
SAFETY INSTRUCTIONS
!While power is on or when the inverter is running, do not open the front cover. You may get an electric shock.
!Do not run the inverter with the front cover removed. Otherwise, you may access the exposed high-voltage termi-
nals and charging part and get an electric shock.
!If power is off, do not remove the front cover except for wiring or periodic inspection. You may access the
charged inverter circuits and get an electric shock.
!Before starting wiring or inspection, switch power off, wait for more than 10 minutes, and check for no residual
voltage with a tester or the like.
WARNING
CAUTION
WARNING
ib66808b.book 1 ページ ２００２年２月１４日 木曜日 午後７時５８分
A-2
2. Injury Prevention
3. Additional instructions
Also note the following points to prevent an accidental failure, injury, electric shock, etc.:
(1) Transportation and mounting
(2) Test operation and adjustment
!Any person who is involved in the wiring or inspection of this equipment should be fully competent to do the work.
!Always install the option unit before wiring. Otherwise, you may get an electric shock or be injured.
!Handle this option unit with dry hands to prevent an electric shock.
!Do not subject the cables to scratches,excessive stress, heavy loads or pinching. Otherwise, you may get an electric shock.
!Apply only the voltage specified in the instruction manual to each terminal to prevent burst, damage, etc.
!Ensure that the cables are connected to the correct terminals. Otherwise, burst, damage, etc. may occur.
!Always make sure that polarity is correct to prevent burst, damage, etc.
!While power is on or for some time after power-off, do not touch the inverter as it is hot and you may get burnt.
!Do not install or operate the option unit if it is damaged or has parts missing.
!Do not stand or rest heavy objects on the product.
!Check that the mounting orientation is correct.
!Prevent screws, metal fragments or other conductive bodies or oil or other flammable substance from entering the inverter.
!Before starting operation, confirm and adjust the parameters. A failure to do so may cause some machines to
make unexpected motions.
WARNING
C
AUTI
O
N
C
AUTI
O
N
C
AUTI
O
N
ib66808b.book 2 ページ ２００２年２月１４日 木曜日 午後７時５８分
A-3
(3) Usage
(4) Maintenance, inspection and parts replacement
(5) Disposal
(6) General instruction
!Do not modify the equipment.
!When parameter clear or all parameter clear is performed, each parameter returns to the factory setting. Re-set
the required parameters before starting operation.
!For prevention of damage due to static electricity, touch nearby metal before touching this product to eliminate
static electricity from your body.
!Do not test the equipment with a megger (measure insulation resistance).
!Treat as industrial waste.
All illustrations given in this manual may have been drawn with covers or safety guards removed to provide in-
depth description. Before starting operation of the product, always return the covers and guards into original posi-
tions as specified and operate the equipment in accordance with the manual.
WARNING
C
AUTI
O
N
C
AUTI
O
N
C
AUTI
O
N
ib66808b.book 3 ページ ２００２年２月１４日 木曜日 午後７時５８分
CONTENTS
1.PRE-OPERATION INSTRUCTIONS 1
1.1 Unpacking and Product Confirmation..................................................................................................1
1.2 Packing Confirmation...........................................................................................................................1
1.3 Structure ..............................................................................................................................................2
2.INSTALLATION 3
2.1 Pre-Installation Instructions..................................................................................................................3
2.2 Installation Procedure..........................................................................................................................3
2.3 Wiring...................................................................................................................................................5
3.12-BIT DIGITAL INPUT 6
3.1 Wiring Examples..................................................................................................................................6
3.2 Terminals.............................................................................................................................................8
4.PARAMETERS 9
4.1 Parameter List......................................................................................................................................9
4.2 Parameter Setting..............................................................................................................................11
4.3 Instructions.........................................................................................................................................16
5.SPECIFICATIONS 18
5.1 Specifications.....................................................................................................................................18
ib66808b.book 4 ページ ２００２年２月１４日 木曜日 午後７時５８分
1
1.PRE-OPERATION INSTRUCTIONS
1.1 Unpacking and Product Confirmation
Take the option unit out of the package, check the unit name, and confirm that the product is as you
ordered and intact.
Functions arailable differ between FR-A500(L)/F500(L) series and FR-V500 series, always check before
using.
"SERIAL number check
This product may be used with the FR-A520-0.4K to 22K manufactured in and after July 1997. Any of the
models may be used with this unit if its SERIAL number indicated on the rating plate and package has
"J77######" or later version.
SERIAL is made up of 1 version symbol and 8 numeric characters indicating year, month, and control
number as shown below.
SERIAL number
1.2 Packing Confirmation
Make sure that the package includes the following
" Instruction manual.........................................................................1
" Mounting screws M3 × 10 .............................................................2
J 7 7 ######
Symbol Year Month Control number
ib66808b.book 1 ページ ２００２年２月１４日 木曜日 午後７時５８分
2
PRE-OPERATION INSTRUCTIONS
1.3 Structure
FR-A5AX
Connector
Mounting
hole
Terminal
block
screw
size M3
Terminal
symbol
Front view Mounting holes
Option fixing holes
Rear view Mounting
hole
X0 X1 X5 X6 X11
X2 X10
X7 X9
X8 DY
X3 X4
ib66808b.book 2 ページ ２００２年２月１４日 木曜日 午後７時５８分
3
2.INSTALLATION
2.1 Pre-Installation Instructions
Make sure that the input power of the inverter is off.
2.2 Installation Procedure
(1) Securely insert the connector of the option unit far into the connector of the inverter. At this time, fit the
option fixing holes snugly. For the position of slot, refer to the next page.
Also be sure to fit the unit into the option fixing hook (For the FR-A500(L)/ FR-F500(L) series, it is avail-
able in Aug., 2000).
(2) Securely fix the option unit to the inverter on both sides with the accessory mounting screws. If the
screw holes do not match, the connector may not have been plugged snugly. Checkfor loose plugging.
With input power on, do not install or remove the option unit. Otherwise, the inverter and
option unit may be damaged.
CAUTION
ib66808b.book 3 ページ ２００２年２月１４日 木曜日 午後７時５８分
4
INSTALLATION
CAUTION
1. Only one type of option per inverter may be used. When two or more options are mounted, pri-
ority is in order of slots 1, 2 and 3, the options having lower priority are inoperative.
2. When the inverter cannot recognize that the option is
mounted, it displays the option error. The errors shown
differ according to the mounting slots 1, 2, 3.
Option unit
A
ccessory screw
(2 pcs.)
Option side
connector
Inverter
(without cover)
Slot 1
Inverter side connector
Slot 2
Slot 3
Option fixing hook
The slots 1, 2, and 3 are provided
with an option fixing hook.
Mounting Position Error Display
Slot 1 E.OP1
Slot 2 E.OP2
Slot 3 E.OP3
ib66808b.book 4 ページ ２００２年２月１４日 木曜日 午後７時５８分
5
INSTALLATION
2.3 Wiring
Route the wires so that they do not take up a lot of space in the control circuit terminal block of the option unit.
During wiring, do not leave wire off-cuts in the inverter. They may cause a fault, failure or malfunction.
Use the space on the left side of the control circuit terminal unit to route the wires.
REMARKS
The wires with large gaze may not be connected to the terminal block. When connected in parallel, all wires may not
fit in the wiring space due to the increased number of wires. In such cases, perform wiring by using a junction termi-
nal block.
When installing the inverter front cover, the cables to the inverter's control circuit terminals
and option terminals should be routed properly in the wiring space to prevent them from
being caught between the inverter and its cover.
Cable routing
CAUTION
ib66808b.book 5 ページ ２００２年２月１４日 木曜日 午後７時５８分
Tabla de contenidos
Otros manuales de Inversor de Mitsubishi Electric
Mitsubishi Electric
Mitsubishi Electric A800 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric FR-A7AR E Manual de usuario
Mitsubishi Electric
Mitsubishi Electric FR-A8AP Manual de usuario
Mitsubishi Electric
Mitsubishi Electric CC-Link IE TSN FR-A8NCG Manual de usuario
Mitsubishi Electric
Mitsubishi Electric FR-D720-008 Hoja de instrucciones
Mitsubishi Electric
Mitsubishi Electric FR-E720-0.1KNC Manual de usuario
Mitsubishi Electric
Mitsubishi Electric 800 Series Manual de usuario
Mitsubishi Electric
Mitsubishi Electric 800 Series Manual de usuario
Mitsubishi Electric
Mitsubishi Electric FR-XCG-K Series Manual de usuario
Mitsubishi Electric
Mitsubishi Electric fr-e700 series Guía de instalación
Mitsubishi Electric
Mitsubishi Electric FR-D720-070 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric FR-A820-04750-GF Manual de usuario
Mitsubishi Electric
Mitsubishi Electric FR-E720-0.1K Manual de usuario
Mitsubishi Electric
Mitsubishi Electric fr-e720-008 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric 800 Series Manual de lista de piezas
Mitsubishi Electric
Mitsubishi Electric FR-A700 Series Manual de usuario
Mitsubishi Electric
Mitsubishi Electric FR-A7AL Manual de usuario
Mitsubishi Electric
Mitsubishi Electric FR-E520 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric FR-A8AY E KIT Manual de usuario
Mitsubishi Electric
Mitsubishi Electric FR-E5NC Manual de usuario
