Mitsubishi Electric FR-A7AR E Manual de usuario
A-1
Thank you for choosing this Mitsubishi Electric inverter plug-in
option.
This Instruction Manual provides handling information and
precautions for use of this product. Incorrect handling might
cause an unexpected fault. Before using this product, read all
relevant instruction manuals carefully to ensure proper use.
Please forward this Instruction Manual to the end user.
1. Electric shock prevention
2. Injury prevention
This section is specifically about
safety matters
Do not attempt to install, operate, maintain or inspect this
product until you have read this Instruction Manual and
supplementary documents carefully. Do not use this product
until you have a full knowledge of this product mechanism,
safety information and instructions.
In this Instruction Manual, the safety instruction levels are
classified into "WARNING" and "CAUTION".
Incorrect handling may cause hazardous
conditions, resulting in death or severe
injury.
Incorrect handling may cause hazardous
conditions, resulting in medium or slight
injury, or may cause only material
damage.
Note that even the level may lead to a serious
consequence depending on conditions. Be sure to follow the
instructions of both levels as they are critical to personnel safety.
WARNING
CAUTION
CAUTION
SAFETY INSTRUCTIONS
WARNING
Do not remove the front cover or the wiring cover of the
inverter while the inverter power is ON. Do not operate the
inverter with any cover or wiring cover removed, as accidental
contact with exposed high-voltage terminals and internal
components may occur, resulting in an electrical shock.
Even if power is OFF, do not remove the front cover of the
inverter except for wiring or periodic inspection as you may
accidentally touch the charged circuits and get an electric shock.
Before wiring or inspection, check that the display of the
inverter operation panel is OFF. Any person who is involved in
wiring or inspection shall wait for 10 minutes or longer after
power OFF and check that there are no residual voltage using a
tester or the like. The capacitor is charged with high voltage for
some time after power OFF, and it is dangerous.
Any person who is involved in wiring or inspection of this
product shall be fully competent to do the work.
This product must be installed before wiring. Otherwise you
may get an electric shock or be injured.
Do not subject the cables to scratches, excessive stress, heavy
loads or pinching. Doing so may cause an electric shock.
Do not touch this product or handle the cables with wet hands.
Doing so may cause an electric shock.
CAUTION
The voltage applied to each terminal must be as specified in the
Instruction Manual. Otherwise an explosion or damage may occur.
The cables must be connected to the correct terminals.
Otherwise
an explosion or damage
may occur.
The polarity (+ and -) must be correct. Otherwise
an explosion
or damage
may occur.
While power is ON or for some time after power OFF, do not touch
the inverter as it will be extremely hot. Doing so may cause burns.
A-2
3. Additional instructions
The following instructions must be also followed. If this product is
handled incorrectly, it may cause unexpected fault, an injury, or an
electric shock.
1) Transportation and installation
2) Test operation
3) Usage
4) Maintenance, inspection and parts replacement
5) Disposal
6) General instruction
CAUTION
Do not install or operate the plug-in option if it is damaged or
has parts missing.
Do not stand or place heavy objects on this product.
Ensure the mounting orientation of this product is correct.
Foreign conductive objects must be prevented from entering
the inverter. That includes screws and metal fragments or
other flammable substance such as oil.
If halogens (including fluorine, chlorine, bromine, and iodine),
contained in fumigants for wood packages enter this product,
the product may be damaged. Prevent the entry of fumigant
residuals or use an alternative method such as heat
disinfection. Note that sterilization or disinfection of wood
packages should also be performed before packing the
product.
CAUTION
Before starting operation, confirm or adjust the parameter
settings. Failure to do so may cause some machines to make
unexpected motions.
WARNING
Do not modify this product.
Do not remove any part which is not instructed to be removed
in the Instruction Manuals. Doing so may lead to a failure or
damage of this product.
CAUTION
As all parameters return to their initial values after Parameter clear
or All parameter clear is performed, the needed parameters for
operation of the inverter and this product must be set again before
the operation is started.
To avoid damage to this product due to static electricity, static
electricity in your body must be discharged before you touch
this product.
CAUTION
Do not carry out a megger (insulation resistance) test.
CAUTION
This product must be treated as industrial waste.
For clarity, illustrations in this Instruction Manual may be drawn
with covers or safety guards removed. Ensure all covers and
safety guards are properly installed prior to starting operation.
I
— CONTENTS —
1 PRE-OPERATION INSTRUCTIONS 1
1.1 Unpacking and Product Confirmation .............................................................................................1
1.1.1 Packing confirmation (FR-A700/F700 series)................................................................................................. 1
1.1.2 Packing confirmation (FR-E700 series (E kit)) ............................................................................................... 2
1.2 Parts ....................................................................................................................................................3
1.3 Specifications.....................................................................................................................................4
2 INSTALLATION AND WIRING (FR-A700/F700 SERIES) 5
2.1 Pre-Installation Instructions .............................................................................................................5
2.2 Installation Procedure .......................................................................................................................6
2.3 Wiring..................................................................................................................................................8
3 INSTALLATION AND WIRING (FR-E700 SERIES (E kit)) 11
3.1 Pre-Installation Instructions ...........................................................................................................11
3.2 Installation Procedure .....................................................................................................................11
3.3 Wiring................................................................................................................................................17
4 RELAY OUTPUT 20
4.1 Internal Block Diagram....................................................................................................................20
4.2 Terminals ..........................................................................................................................................21
4.3 Parameter List ..................................................................................................................................21
4.4 Output Signal List (FR-A700/F700 series) .....................................................................................22
4.5 Output Signal List (FR-E700 series)...............................................................................................24
4.6 Connection Diagram When Using Electronic Bypass Sequence Function (FR-A700/F700
series) ...............................................................................................................................................25
II
APPENDIX 26
Appendix 1 Instructions for compliance with the EU Directives .......................................................26
Appendix 2 Instructions for EAC ..........................................................................................................27
Appendix 3 Restricted Use of Hazardous Substances in Electronic and Electrical Products........28
Appendix 4 Referenced Standard (Requirement of Chinese standardized law) ..............................29
1
1PRE-OPERATION INSTRUCTIONS
1.1 Unpacking and Product Confirmation
Take the plug-in option out of the package, check the product name, and confirm that the product is as you
ordered and intact.
This product is a plug-in option dedicated for the FR-A700/F700/E700 series.
1.1.1 Packing confirmation (FR-A700/F700 series)
Check the enclosed items.
Plug-in option
......................................... 1
Mounting screw (M3 6mm)
.............. 2 (Refer to page 6.)
Hex-head screw for option
mounting (5.5mm)
............... 1 (Refer to page 6.)
5.5mm
2
PRE-OPERATION INSTRUCTIONS
1
1.1.2 Packing confirmation (FR-E700 series (E kit))
Check the enclosed items.
*1 Used with the FR-E720-3.7K (FR-E720-175) or less and FR-E740-7.5K (FR-E740-170) or less.
*2 Used with the FR-E720-5.5K (FR-E720-240) or more and FR-E740-11K (FR-E740-230) or more.
Plug-in option
............................................... 1
Mounting screw (M3
6mm)
............ 2
(Refer to page 13, 16)
Front cover for plug-in option
...............1
(Refer to page 13, 16)
Option protective cover
*1
...................... 1
(Refer to page 13)
Option small cover
*2
................... 1
(Refer to page 16)
Insulation sheet
...............1
(Refer to page 13, 16)
CAUTION
• In place of the inverter front cover, install a provided front cover for plug-in option.
4
PRE-OPERATION INSTRUCTIONS
1
1.3 Specifications
(1) Types of output signal
1 changeover contact output (three relays are provided)
(2) Contact capacity
230VAC .......... 0.3A
30VDC............ 0.3A
CAUTION
• The contacts should be used within the rated capacity to prevent contacts weld resulting from faster
contacts wearing.
5
2INSTALLATION AND WIRING (FR-A700/F700 SERIES)
2.1 Pre-Installation Instructions
Make sure that the input power of the inverter is off.
CAUTION
With input power on, do not install or remove the plug-in option. Otherwise, the inverter and
plug-in option may be damaged.
For prevention of damage due to static electricity, touch nearby metal before touching this
product to eliminate static electricity from your body.
Otros manuales para FR-A7AR E
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Inversor de Mitsubishi Electric
Mitsubishi Electric
Mitsubishi Electric 800 Series Manual de usuario
Mitsubishi Electric
Mitsubishi Electric FR-A8AX Manual de usuario
Mitsubishi Electric
Mitsubishi Electric FR-E720-600 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric FR-A700-A1 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric 800 Series Manual de usuario
Mitsubishi Electric
Mitsubishi Electric Freqrol Z024-UL Manual de usuario
Mitsubishi Electric
Mitsubishi Electric 800 Series Manual de usuario
Mitsubishi Electric
Mitsubishi Electric FR-A7AP Manual de usuario
Mitsubishi Electric
Mitsubishi Electric FREQROL-CS80 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric 700 Series Manual de usuario
Mitsubishi Electric
Mitsubishi Electric FR-A802-P Manual de usuario
Mitsubishi Electric
Mitsubishi Electric 800 Series Manual de usuario
Mitsubishi Electric
Mitsubishi Electric FR-A8NCE Manual de usuario
Mitsubishi Electric
Mitsubishi Electric FR-S520E Series Manual de usuario
Mitsubishi Electric
Mitsubishi Electric FR-A862 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric A800 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric 800 Series Manual de usuario
Mitsubishi Electric
Mitsubishi Electric FR-D720 K Series Manual de usuario
Mitsubishi Electric
Mitsubishi Electric 700 Series Manual de usuario
Mitsubishi Electric
Mitsubishi Electric PV-PNS03ATL-GER Manual de usuario
