Mitsubishi Electric MELSEC Q Series Manual de usuario

Temperature Control Module

User's Manual

-Q64TCTT

-Q64TCTTBW

-Q64TCRT

-Q64TCRTBW

-GX Configurator-TC (SW0D5C-QTCU-E)

Downloaded from ManualsNet.com search engine

A - 1 A - 1

SAFETY PRECAUTIONS 

(Read these precautions before using this product.)

Before using this product, please read this manual and the relevant manuals carefully and pay full

attention to safety to handle the product correctly.

The instructions given in this manual are concerned with this product. For the safety instructions of the

programmable controller system, please read the CPU module User's Manual.

In this manual, the safety precautions are classified into two levels: " WARNING " and " CAUTION".

Indicates that incorrect handling may cause hazardous conditions,

resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous conditions,

resulting in minor or moderate injury or property damage.

Under some circumstances, failure to observe the precautions given under " CAUTION" may lead to

serious consequences.

Make sure that the end users read this manual and then keep the manual in a safe place for future

reference.

[Design Precautions]

WARNING

Do not write data into the "read-only area" in the buffer memory of the intelligent function

module. In addition, do not turn on/off the "reserved" signals among the I/O signals transferred

to/from the programmable controller CPU.

Doing so can malfunction the programmable controller system.

Depending on the malfunction of the external output transistor, there may be cases where the

output is on or off status. Install external monitoring circuitry for output signals that may lead to

major accidents.

CAUTION

Do not bunch the control wires or communication cables with the main circuit or power wires, or

install them close to each other.

They should be installed 100 mm(3.94 inch) or more from each other.

Not doing so could result in noise that may cause malfunction.

! !

WARNING

CAUTION

Downloaded from ManualsNet.com search engine

A - 2 A - 2

[Installation Precautions]

CAUTION

Use the programmable controller in an environment that meets the general specifications

contained in the CPU User's Manual.

Using this programmable controller in an environment outside the range of the general

specifications may cause electric shock, fire, malfunction, and damage to or deterioration of the

product.

While pressing the installation lever located at the bottom of module, insert the module fixing tab

into the fixing hole in the base unit until it stops. Then, securely mount the module with the fixing

hole as a supporting point.

Improper installation may result in malfunction, breakdown or the module coming loose and

dropping. Securely fix the module with screws if it is subject to vibration during use.

Tighten the screws within the range of specified torque.

If the screws are loose, it may cause the module to fallout, short circuits, or malfunction.

If the screws are tightened too much, it may cause damage to the screw and/or the module,

resulting in fallout, short circuits or malfunction.

Be sure to shut off all phases of the external power supply used by the system before mounting

or removing the module.

Not ding so may cause electric shock or damage to the module.

In the system where a CPU module supporting the online module change is used and on the

MELSECNET/H remote I/O stations, modules can be replaced online (during energizing).

However, there are some restrictions on replaceable modules and the replacement procedures

are predetermined for each module.

For details, refer to the chapter of the online module change in this manual.

Do not directly touch the conductive area or electronic components of the module.

Doing so may cause malfunction or failure in the module.

Downloaded from ManualsNet.com search engine

A - 3 A - 3

[Wiring Precautions]

CAUTION

Be careful not to let foreign matters such as sawdust or wire chips get inside the module.

They may cause fires, failure or malfunction.

The top surface of the module is covered with protective film to prevent foreign objects such as

cable offcuts from entering the module when wiring.

Do not remove this film until the wiring is complete.

Before operating the system, be sure to remove the film to provide adequate heat ventilation.

Be sure to fix communication cables or power supply cables leading from the module by placing

them in the duct or clamping them.

Cables not placed in the duct or without clamping may hang or shift, allowing them to be

accidentally pulled, which may cause a module malfunction and cable damage.

Do not grab on the cable when removing the communication or power cable connected to the

module.

When disconnecting a cable without a connector, first loosen the screws on the part that is

connected to the module.

Pulling the cable when it is still connected to the module may cause damage to the module or

cable, or misoperation due to cable contact failure.

Always ground the shielded cable for the programmable controller.

There is a risk of electric shock or malfunction.

Use applicable solderless terminals and tighten them with the specified torque. If any solderless

spade terminal is used, it may be disconnected when the terminal screw comes loose, resulting

in failure.

When wiring, be sure to verify the rated voltage of the product as well as the terminal layout. Fire

or failure may result if incorrect voltage is input or incorrect wiring is performed.

Downloaded from ManualsNet.com search engine

A - 4 A - 4

[Startup/Maintenance Precautions]

CAUTION

Do not disassemble or modify the module.

Doing so could cause failure, malfunction, injury or fire.

Be sure to shut off all phases of the external power supply used by the system before mounting

or removing the module.

Not doing so may cause failure or malfunction of the module.

In the system where a CPU module supporting the online module change is used and on the

MELSECNET/H remote I/O stations, modules can be replaced online (during energizing).

However, there are some restrictions on replaceable modules and the replacement procedures

are predetermined for each module.

For details, refer to the chapter of the online module change in this manual.

Do not install/remove the module to/from the base unit, or the terminal block to/from the module

more than 50 times after the first use of the product. (IEC 61131-2 compliant)

Failure to do so may cause malfunction.

Do not touch the connector while the power is on.

Doing so may cause malfunction.

Always shut off all phases of the external supply power used by the system before cleaning or

retightening screws/module fixing screws.

Not doing so may cause failure or malfunction of the module.

If the screws are loose, it may cause the module to fallout, short circuits, or malfunction.

If the screws are tightened too much, it may cause damages to the screws and/or the module,

resulting in the module falling out, short circuits or malfunction.

Always make sure to touch the grounded metal to discharge the electricity charged in the body,

etc., before touching the module.

Failure to do so may cause a failure or malfunctions of the module.

[Disposal Precautions]

CAUTION

When disposing of the product, handle it as industrial waste.

Downloaded from ManualsNet.com search engine

A - 5 A - 5

CONDITIONS OF USE FOR THE PRODUCT 

(1) Mitsubishi programmable controller ("the PRODUCT") shall be used in conditions;

i) where any problem, fault or failure occurring in the PRODUCT, if any, shall not lead to any major or

serious accident; and

ii) where the backup and fail-safe function are systematically or automatically provided outside of the

PRODUCT for the case of any problem, fault or failure occurring in the PRODUCT.

(2) The PRODUCT has been designed and manufactured for the purpose of being used in general

industries.

MITSUBISHI SHALL HAVE NO RESPONSIBILITY OR LIABILITY (INCLUDING, BUT NOT LIMITED

TO ANY AND ALL RESPONSIBILITY OR LIABILITY BASED ON CONTRACT, WARRANTY, TORT,

PRODUCT LIABILITY) FOR ANY INJURY OR DEATH TO PERSONS OR LOSS OR DAMAGE TO

PROPERTY CAUSED BY the PRODUCT THAT ARE OPERATED OR USED IN APPLICATION NOT

INTENDED OR EXCLUDED BY INSTRUCTIONS, PRECAUTIONS, OR WARNING CONTAINED IN

MITSUBISHI'S USER, INSTRUCTION AND/OR SAFETY MANUALS, TECHNICAL BULLETINS AND

GUIDELINES FOR the PRODUCT.

("Prohibited Application")

Prohibited Applications include, but not limited to, the use of the PRODUCT in;

Nuclear Power Plants and any other power plants operated by Power companies, and/or any other

cases in which the public could be affected if any problem or fault occurs in the PRODUCT.

Railway companies or Public service purposes, and/or any other cases in which establishment of a

special quality assurance system is required by the Purchaser or End User.

Aircraft or Aerospace, Medical applications, Train equipment, transport equipment such as Elevator

and Escalator, Incineration and Fuel devices, Vehicles, Manned transportation, Equipment for

Recreation and Amusement, and Safety devices, handling of Nuclear or Hazardous Materials or

Chemicals, Mining and Drilling, and/or other applications where there is a significant risk of injury to

the public or property.

Notwithstanding the above, restrictions Mitsubishi may in its sole discretion, authorize use of the

PRODUCT in one or more of the Prohibited Applications, provided that the usage of the PRODUCT is

limited only for the specific applications agreed to by Mitsubishi and provided further that no special

quality assurance or fail-safe, redundant or other safety features which exceed the general

specifications of the PRODUCTs are required. For details, please contact the Mitsubishi

representative in your region.

Downloaded from ManualsNet.com search engine

A - 6 A - 6

REVISIONS

* The manual number is given on the bottom left of the back cover.

Print Date Manual Number Revision

Oct., 2000 SH (NA)-080121-A First edition

Jun., 2001 SH (NA)-080121-B Standardize the name from software package (GPP function) to Product

name (GX Developer).

Standardize the name from utility package (QTCU) to Product name (GX

Configurator-TC).

Addition

Section 1.4, Section 2.1, 2.2

Correction

CONFORMATION TO THE EMC DIRECTIVE AND LOW VOLTAGE

INSTRUCTION, ABOUT THE GENERIC TERMS AND

ABBREVIATIONS, PRODUCT STRUCTURE, Section 3.5.47, Section

5.2, 5.2.1, 5.2.2, 5.3.3, 5.6

Feb., 2002 SH (NA)-080121-C Add the contents of the function version C

Addition

Chapter 7

Renumbering

Chapter 7 Chapter 8

Correction

SAFETY PRECAUTIONS, ABOUT THE GENERIC TERMS AND

ABBREVIATIONS, Section 2.1, 2.2, Section 3.1.1, 3.2, 3.2.1, 3.2.10,

3.2.11, 3.5.1, 3.5.11, 3.5.20, 3.5.32, 3.5.42, Section 4.3, Section 5.2.1,

5.2.2, Section 6.2.2, 6.3, Section 8.1

Aug., 2002 SH (NA)-080121-D Correction

Section 2.1, Section 3.1, 3.2.1, 3.2.7, 3.5.1, 3.5.12, 3.5.15, 3.5.20, 3.5.26,

3.5.34, 3.5.35, 3.5.44, 3.5.45, 3.5.49, 3.5.51, 3.5.52, Section 6.3, Section

8.10

Feb., 2003 SH (NA)-080121-E Correction

SAFETY PRECAUTIONS, INTRODUCTION, CONTENTS, Section 2.1,

Section 3.1.1, Section 3.5.38, Section 5.2.2, Section 5.3.3, Section 5.4 to

Section 5.6

May, 2003 SH (NA)-080121-F Correction

Section 2.1, Section 3.5.15, Section 3.5.36, Section 6.3

May, 2004 SH (NA)-080121-G Addition of program example for use on the remote I/O network

Correction

Section 2.1, 2.2, Section 3.5.4, Chapter 6, Section 7.1, 7.3.1, 7.3.2

Oct., 2004 SH (NA)-080121-H Correction

SAFETY PRECAUTIONS, Section 2.1, Section 3.1.1, 3.2.1,

Section 4.1, Section 6.3, 6.3.1, Section 8.1

Downloaded from ManualsNet.com search engine

A - 7 A - 7

* The manual number is given on the bottom left of the back cover.

Print Date Manual Number Revision

Jul., 2005 SH (NA)-080121-I Correction

SAFETY PRECAUTIONS, CONFORMATION TO THE EMC DIRECTIVE

AND LOW VOLTAGE INSTRUCTION, Section 1.3.4, Section 2.1, 2.2,

Section 3.1.1, 3.2.11, 3.4.3, 3.5.2, 3.5.8, Section 4.5, Section 5.1, 5.2.1,

5.3.2, 5.3.3, 5.4, 5.5, 5.6, Section 6.2, 6.2.1, 6.3, 6.3.1, Section 7.2, 7.3.1,

7.3.2, Section 8.10

Mar., 2006 SH(NA)-080121-J Correction

SAFETY PRECAUTIONS, CONFORMATION TO THE EMC DIRECTIVE

AND LOW VOLTAGE INSTRUCTION, Section 3.5.26

Sep., 2007 SH(NA)-080121-K Correction

SAFETY PRECAUTIONS, CONTENTS, CONFORMATION TO THE

EMC DIRECTIVE AND LOW VOLTAGE INSTRUCTION, Chapter 1,

Section 1.1, 1.4, Section 2.1, 2.2, Chapter 3, Section 3.1.1, 3.2, 3.2.1,

3.2.6, 3.2.7, 3.2.10, 3.2.11, 3.2.12, 3.4.1, 3.4.2, 3.4.3, 3.5.1, 3.5.2, 3.5.3,

3.5.16, 3.5.24, 3.5.25, 3.5.30, 3.5.38, 3.5.41, 3.5.42, 3.5.43, 3.5.44,

3.5.48, Section 4.3, 4.4.1, 4.4.2, 4.4.3, Section 5.1, 5.3.1, 5.3.2, 5.3.3,

5.4, 5.5, 5.6, Section 6.2.1, 6.3, Chapter 7, Section 7.1, 7.2, 7.3.1, 7.3.2,

7.4, Section 8.2, 8.3, 8.6, INDEX

Jan., 2008 SH(NA)-080121-L Correction

SAFETY PRECAUTIONS, CONTENTS, ABOUT THE GENERIC TERMS

AND ABBREVIATIONS, Section 2.2 to 2.4, 3.2.1, 3.2.7, 3.5.11, 3.5.34,

5.2.2, 8.9 to 8.11

May, 2008 SH(NA)-080121-M Correction

SAFETY PRECAUTIONS, CONFORMANCE WITH THE EMC AND LOW

VOLTAGE DIRECTIVES, ABOUT THE GENERIC TERMS AND

ABBREVIATIONS, Section 2.1, 2.3, 4.1, 5.2.1, 5.3.1, 5.3.3, 7.1

Feb., 2011 SH(NA)-080121-N Addition

CONDITIONS OF USE FOR THE PRODUCT

Correction

SAFETY PRECAUTIONS, ABOUT THE GENERIC TERMS AND

ABBREVIATIONS, Section 1.1, Section 2.1 to 2.3, Section 3.1.1, 3.2.1,

3.2.2, 3.2.4 to 3.2.7, 3.2.11, 3.3, 3.4.2, 3.4.3, 3.5.1, 3.5.3, 3.5.5 to 3.5.8,

3.5.11, 3.5.12 to 3.5.20, 3.5.23 to 3.5.27, 3.5.29, 3.5.31 to 3.5.34, 3.5.37,

3.5.41, 3.5.43, 3.5.45 to 3.5.47, 3.5.49, Section 4.3, 4.4.1 to 4.4.3,

Section 5.1, 5.4, 5.6, 5.2.1, Section 6.2.1, 6.3.1, 6.3.2, Section 7.1, 7.3.1,

7.3.2, 8.1, Section 8.2, 8.5, 8.11, 8.12, Appendix 1

Jul., 2015 SH(NA)-080121-O Addition

Section 2.4

Japanese Manual Version SH-080108-R

This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent

licenses. Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property

rights which may occur as a result of using the contents noted in this manual.

2000 MITSUBISHI ELECTRIC CORPORATION

Downloaded from ManualsNet.com search engine

A - 8 A - 8

INTRODUCTION

Thank you for the purchasing the MELSEC-Q series programmable controller.

Before using the equipment, please read this manual carefully to develop full familiarity with the functions

and performance of the Q series programmable controller you have purchased, so as to ensure correct use.

CONTENTS

SAFETY PRECAUTIONS .............................................................................................................................A- 1

CONDITIONS OF USE FOR THE PRODUCT .............................................................................................A- 5

REVISIONS ....................................................................................................................................................A- 6

INTRODUCTION............................................................................................................................................A- 8

CONTENTS....................................................................................................................................................A- 8

CONFORMANCE WITH THE EMC AND LOW VOLTAGE DIRECTIVES..................................................A-12

ABOUT THE GENERIC TERMS AND ABBREVIATIONS...........................................................................A-13

PRODUCT STRUCTURE..............................................................................................................................A-13

1 GENERAL DESCRIPTION 1- 1 to 1-12

1.1 Features ................................................................................................................................................... 1- 3

1.2 The PID Control System .......................................................................................................................... 1- 5

1.3 About the PID Operation.......................................................................................................................... 1- 6

1.3.1 Operation method and formula......................................................................................................... 1- 6

1.3.2 The Q64TC actions ........................................................................................................................... 1- 7

1.3.3 Proportional action (P-action) ........................................................................................................... 1- 8

1.3.4 Integral action (I-action) .................................................................................................................... 1- 9

1.3.5 Derivative action (D-action)............................................................................................................... 1-10

1.3.6 PID action .......................................................................................................................................... 1-11

1.4 Functions Added to Function Version B and Later ................................................................................. 1-12

2 SYSTEM CONFIGURATION 2- 1 to 2-11

2.1 Applicable Systems.................................................................................................................................. 2- 1

2.2 For Use the Q64TC with Redundant CPUs ............................................................................................ 2- 6

2.3 Checking Function Version/Serial No./Product Information/Software Version...................................... 2- 7

2.4 Precautions for System Configuration..................................................................................................... 2-10

3 SPECIFICATIONS 3- 1 to 3-60

3.1 Performance Specifications ..................................................................................................................... 3- 1

3.1.1 Performance specifications of the Q64TC ....................................................................................... 3- 1

3.1.2 Usable temperature sensor types, measurement temperature ranges and data resolutions ........ 3- 3

3.2 Function Summary................................................................................................................................... 3- 4

3.2.1 Auto tuning function .......................................................................................................................... 3- 5

3.2.2 Reverse/Forward action select function ........................................................................................... 3-10

3.2.3 RFB limiter function ........................................................................................................................... 3-10

3.2.4 Sensor compensation function ......................................................................................................... 3-10

3.2.5 Unused channel setting .................................................................................................................... 3-11

3.2.6 Forced PID control stop .................................................................................................................... 3-11

3.2.7 Heater disconnection detection function (available for the Q64TCTTBW, Q64TCRTBW only) ... 3-12

Downloaded from ManualsNet.com search engine

Otros manuales para MELSEC Q Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Controladores de Mitsubishi Electric

Mitsubishi Electric

Mitsubishi Electric Q Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PAC-YT51CRB Manual de usuario

Mitsubishi Electric

Mitsubishi Electric SIMPLE MA PAC-YT51CRB Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC Q Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manual del propietario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC-Q00U(J)CPU Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC Q Series Manual del propietario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F FX5 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC FX2N-16CCL-M Manual de usuario

Mitsubishi Electric

Mitsubishi Electric WS0-CPU0 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric CR750-Q Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC FX Series Manual del propietario

Mitsubishi Electric

Mitsubishi Electric FX2N-2DA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F FX5 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F FX5 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric CR750 Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FX3U-ENET-ADP Manual de usuario

Mitsubishi Electric

Mitsubishi Electric R60TD8-G Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Melservo-J5 MR-J5 Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FX5-DP-M Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC L-Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FX2N-32ASI-M Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario