Mitsubishi Electric AJ65BT-D75P2-S3 Manual de usuario

AJ65BT-D75P2-S3 Positioning Module

User's Manual

A - 1

SAFETY PRECAUTIONS

(Read these precautions before using this product.)

Before using this product, please read this manual and the relevant manuals carefully and pay full

attention to safety to handle the product correctly.

The precautions given in this manual are concerned with this product only. For the safety precautions of

the programmable controller system, refer to the user's manual for the CPU module used.

In this manual, the safety instructions are classified into two levels: " WARNING" and " CAUTION".

Under some circumstances, failure to observe the precautions given under " CAUTION" may lead to

serious consequences.

Observe the precautions of both levels because they are important for personal and system safety.

Make sure that the end users read this manual and then keep the manual in a safe place for future

reference.

A - 2

[Design Precautions]

WARNING

Failure to observe this could lead to accidents for incorrect outputs or malfunctioning.

Configure safety circuits external to the programmable controller to ensure that the entire

system operates safely even when a fault occurs in the external power supply or the

programmable controller.

Failure to do so may result in an accident due to an incorrect output or malfunction.

(1) Configure an emergency stop circuit and interlock circuit such as a positioning upper

limit/lower limit to prevent mechanical damage outside the programmable controller.

(2) The machine zero point return operation is controlled by the zero point return direction

and zero point return speed data. Deceleration starts when the near-point dog turns ON.

Thus, if the zero point return direction is incorrectly set, deceleration will not start and the

machine will continue to travel. Configure an interlock circuit to prevent mechanical

damage outside the programmable controller.

(3) When the positioning module detects an error, the motion slows down and stops or the

motion suddenly stops, depending on the stop group setting in parameter.

Set the parameters to meet the specifications of the positioning control system used.

In addition, set the OPR parameters and positioning data within the specified setting range.

When a data link results in a communication error, the operating status of the station in

communication error changes depending on the type of the used data link. Using the

communication status information, configure an interlock circuit in the sequence program to

ensure that the system will operate safely.

For the method of checking the station in communication error and its operating status at

communication error, refer to the corresponding data link manual.

[Design Precautions]

CAUTION

Do not install the control lines or communication cables together with the main circuit lines or

power cables.

Keep a distance of 100mm or more between them.

Failure to do so may result in malfunction due to noise.

A - 3

[Installation Precautions]

CAUTION

Use the programmable controller in an environment that meets the general specifications in

this manual.

Failure to do so may result in electric shock, fire, malfunction, or damage to or deterioration of

the product.

Securely fix the module using the DIN rail or mounting screws and fully tighten the mounting

screws within the specified torque range. If the screws are loose, it may result in fallout, short

circuits, or malfunctions. Tightening the screw too far may cause damages to the screws and/or

the module, resulting in a fallout, short circuits, or malfunctions.

Securely connect the external device connection connector and peripheral device connection

connector into the module connector until a click is heard.

Improper connection could lead to a connection fault, and to incorrect inputs and outputs.

When not connecting the drive unit and peripheral device, always install a cover on the

connector section.

Failure to observe this could lead to malfunctioning.

[Wiring Precautions]

WARNING

Check the rated voltage and terminal layout before wiring to the programmable controller, and

connect the cables correctly. Connecting a power supply with a different voltage rating or

incorrect wiring may cause a fire or failure.

Check the terminal layout before wiring to the module, and connect the cables correctly.

Prevent foreign matter such as dust or wire chips from entering the module.

Such foreign matter can cause a fire, failure, or malfunction.

[Wiring Precautions]

!CAUTION

Tighten the terminal screws within the range of the specified torque.

If the terminal screws are loose, it may result in short circuits, or malfunctions. Tightening the

terminal screws too far may cause damages to the terminal screws and/or the module, resulting

in short circuits, or malfunctions.

Be sure there are no foreign substances such as sawdust or wiring debris inside the module.

Such debris could cause fires, failure, or malfunction.

Individually ground the FG terminal of the programmable controller with a ground resistance of

100 ohms or less. Failure to do so may result in malfunction.

Place the cables in a duct or clamp them.

If not, dangling cable may swing or inadvertently be pulled, resulting in damage to the module

or cables or malfunction due to poor contact.

Keep a certain distance between the control wires and the communication cables.

Noise can cause a malfunction.

When disconnecting a cable from the module, do not pull on the cable itself. Disconnect cables

not fitted with a connectors by holding and pulling the cable connector.

Disconnect cables not fitted with a connector by removing the screws from the part connected

to the module can cause damage to the module or cable, or ,malfunction due to cable

connection faults.

A - 4

[Startup and Maintenance Precautions]

!CAUTION

Do not touch any terminal while power is on.

Doing so will cause electric shock or malfunction.

Never disassemble or modify the module.

Failure to observe this could lead to trouble, malfunctioning, injuries or fires.

Switch off all phases of the externally supplied power used in the system before cleaning or

tightening the screws.

Failure to turn all phases OFF could lead to electric shocks.

Make sure to install or remove the module from the panel after switching off all phases of the

externally supplied power for the system.

Failure to turn all phases OFF could lead to module trouble or malfunctioning.

Before starting test operation, set the parameter speed limit value to the slowest value, and

make sure that operation can be stopped immediately if a hazardous state occurs.

Do not install/remove the terminal block more than 50 times after the first use of the product.

(IEC 61131-2 compliant)

Always make sure to touch the grounded metal to discharge the electricity charged in the body,

etc., before touching the module.

Failure to do so may cause a failure or malfunctions of the module.

[Precautions for use]

!CAUTION

Note that when the reference axis speed is designated for interpolation operation, the speed of

the partner axis (2nd axis) may be larger than the set speed (larger than the speed limit value).

[Disposal Precautions]

!CAUTION

When disposing of the product, handle it as industrial waste.

A - 5

CONDITIONS OF USE FOR THE PRODUCT

(1) Mitsubishi programmable controller ("the PRODUCT") shall be used in conditions;

i) where any problem, fault or failure occurring in the PRODUCT, if any, shall not lead to any major or

serious accident; and

ii) where the backup and fail-safe function are systematically or automatically provided outside of the

PRODUCT for the case of any problem, fault or failure occurring in the PRODUCT.

(2) The PRODUCT has been designed and manufactured for the purpose of being used in general

industries.

MITSUBISHI SHALL HAVE NO RESPONSIBILITY OR LIABILITY (INCLUDING, BUT NOT LIMITED

TO ANY AND ALL RESPONSIBILITY OR LIABILITY BASED ON CONTRACT, WARRANTY, TORT,

PRODUCT LIABILITY) FOR ANY INJURY OR DEATH TO PERSONS OR LOSS OR DAMAGE TO

PROPERTY CAUSED BY the PRODUCT THAT ARE OPERATED OR USED IN APPLICATION NOT

INTENDED OR EXCLUDED BY INSTRUCTIONS, PRECAUTIONS, OR WARNING CONTAINED IN

MITSUBISHI'S USER, INSTRUCTION AND/OR SAFETY MANUALS, TECHNICAL BULLETINS AND

GUIDELINES FOR the PRODUCT.

("Prohibited Application")

Prohibited Applications include, but not limited to, the use of the PRODUCT in;

• Nuclear Power Plants and any other power plants operated by Power companies, and/or any other

cases in which the public could be affected if any problem or fault occurs in the PRODUCT.

• Railway companies or Public service purposes, and/or any other cases in which establishment of a

special quality assurance system is required by the Purchaser or End User.

• Aircraft or Aerospace, Medical applications, Train equipment, transport equipment such as Elevator

and Escalator, Incineration and Fuel devices, Vehicles, Manned transportation, Equipment for

Recreation and Amusement, and Safety devices, handling of Nuclear or Hazardous Materials or

Chemicals, Mining and Drilling, and/or other applications where there is a significant risk of injury to

the public or property.

Notwithstanding the above, restrictions Mitsubishi may in its sole discretion, authorize use of the

PRODUCT in one or more of the Prohibited Applications, provided that the usage of the PRODUCT is

limited only for the specific applications agreed to by Mitsubishi and provided further that no special

quality assurance or fail-safe, redundant or other safety features which exceed the general

specifications of the PRODUCTs are required. For details, please contact the Mitsubishi representative

in your region.

A - 6

REVISIONS

*The manual number is given on the bottom left of the back cover.

Print Date * Manual Number Revision

Apr., 1998 IB (NA)-66824-A First printing

Apr., 2003 IB (NA)-66824-B Complete review

Oct., 2003 IB (NA)-66824-C Complete review

Feb.,2004 IB (NA)-66824-D

Partial correction addition

CONTENTS, Section 3.5, Section 5.6.2, Section 7.1.2, Section 8.2.5,

Section 8.2.6, Section 10.1.2, Section 10.3.3 to Section 10.3.5,

Section 10.3.8, Appendix 13, INDEX

Jun., 2005 IB (NA)-66824-E Partial correction addition

SAFETY INSTRUCTIONS, Generic Terms and Abbreviations,

Section 3.4.2, Section 4.2.2, Section 4.3, Section 4.5.1, Section 4.5.3,

Section 4.8.1, Section 5.1.2, Section 5.2.1, Section 5.3, Section 5.7.2,

Section 6.1.1, Section 6.6.1, Section 6.6.5, Section 8.1.1,

Section 8.2.4 to Section 8.2.8, Section 8.5, Section 9.1.2,

Section 9.15, Section 9.2.6, Section 9.2.8 to Section 9.2.11,

Section 10.3.9, Section 11.3.1, Section 12.2.1, Section 14.4.3,

Section 12.4.4, Section 12.5.1, Section 12.5.2, Section 12.7.1,

Section 12.7.5, Section 12.7.6, Section 13.4, Section 14.2,

Section 14.3, Appendix 5.1, Appendix 11, Appendix 12

Jul., 2006 IB (NA)-66824-F Partial correction addition

Appendix 7.1, INDEX

Sep., 2007 IB(NA)-66824-G Partial revisions

Section 5.1.2, Section 5.2.1, Section 5.6.1, Section 5.7.1

Apr., 2015 IB(NA)-66824-H Addition

CONDITIONS OF USE FOR THE PRODUCT

Partial correction addition

SAFETY PRECAUTIONS, INTRODUCTION, ABOUT MANUALS,

COMPLIANCE WITH EMC AND LOW VOLTAGE DIRECTIVES,

GENERIC TERMS AND ABBREVIATIONS, Section 1.3, 2.3, 2.4, 3.1,

3.2, 3.7.1, 3.7.3, 3.7.4, 4.1.2, 4.1.3, 4.2.1, 4.3, 4.5.1, 4.5.2, 4.8.1,

5.1.1, 5.2.3, 5.3, 5.5, 6.1.1, 6.1.2, 9.1.4, 9.1.5, 9.2.7, 10.1.1, 10.1.2,

10.3.5, 10.3.8, 10.4.1, 10.4.2, 12.3.2, 12.4.3, 12.4.4, 12.5.3, 13.4,

Appendix 1, 2, 3.2, 5.1, 5.2, 5.3, 6.1, 7.1, 8.1, 9.1, 11, 12,

WARRANTY

Jun., 2017 IB(NA)-66824-I Partial correction addition

Appendix 8.1, 9.1, 12

Japanese Manual Version SH-3654-K

This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent licenses.

Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which

may occur as a result of using the contents noted in this manual.

1998 MITSUBISHI ELECTRIC CORPORATION

A - 7

MEMO

A - 8

INTRODUCTION

Thank you for purchasing the Mitsubishi Electric general-purpose programmable controller MELSEC-A Series.

Always read through this manual, and fully comprehend the functions and performance of the A Series PLC

before starting use to ensure correct usage of this product.

When applying the program examples introduced in this manual to an actual system, ensure the applicability

and confirm that it will not cause system control problems.

CONTENTS

SAFETY PRECAUTIONS............................................................................................................................ A- 1

CONDITIONS OF USE FOR THE PRODUCT ........................................................................................... A- 5

REVISIONS .................................................................................................................................................. A- 6

INTRODUCTION.......................................................................................................................................... A- 8

CONTENTS.................................................................................................................................................. A- 8

ABOUT MANUALS .......................................................................................................................................A- 15

COMPLIANCE WITH EMC AND LOW VOLTAGE DIRECTIVES.........................................................A- 16

USING THIS MANUAL (1)............................................................................................................................A- 17

USING THIS MANUAL (2)............................................................................................................................A- 18

USING THIS MANUAL (3)............................................................................................................................A- 19

GENERIC TERMS AND ABBREVIATIONS ................................................................................................A- 20

ENCLOSED PARTS .....................................................................................................................................A- 21

SECTION 1 PRODUCT SPECIFICATIONS AND HANDLING

1. PRODUCT OUTLINE 1- 1 to 1- 20

1.1 Positioning control.................................................................................................................................. 1- 2

1.1.1 Features of D75P2 .......................................................................................................................... 1- 2

1.1.2 Purpose and applications of positioning control............................................................................. 1- 4

1.1.3 Mechanism of positioning control ................................................................................................... 1- 6

1.1.4 Outline design of positioning system .............................................................................................. 1- 8

1.1.5 Communicating signals between D75P2 and each module........................................................... 1- 10

1.2 Flow of system operation........................................................................................................................ 1- 12

1.2.1 Flow of all processes........................................................................................................................ 1- 12

1.2.2 Outline of starting ............................................................................................................................. 1- 14

1.2.3 Outline of stopping ........................................................................................................................... 1- 16

1.2.4 Outline for restarting......................................................................................................................... 1- 17

1.3 Outline of communication ....................................................................................................................... 1- 18

1.3.1 Cyclic transmission........................................................................................................................... 1- 19

1.3.2 Transient transmission ..................................................................................................................... 1- 20

2. SYSTEM CONFIGURATION 2- 1 to 2- 12

2.1 General image of system....................................................................................................................... 2- 2

2.2 List of configuration devices .................................................................................................................. 2- 4

2.3 Applicable system .................................................................................................................................. 2- 6

2.4 Precautions for use ................................................................................................................................ 2- 8

Otros manuales para AJ65BT-D75P2-S3

Tabla de contenidos

Otros manuales de Controladores de Mitsubishi Electric

Mitsubishi Electric

Mitsubishi Electric FX3U-CAN Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC FX3U-485ADP Manual de usuario

Mitsubishi Electric

Mitsubishi Electric CR800-05VD Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FX3S-10M series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC L series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC-F Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC Q Series Manual del propietario

Mitsubishi Electric

Mitsubishi Electric FX5 MELSEC iQ-F FX5-4LC Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSERVO-JET MR-JET-G-N1 Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC FX-2DA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FX3GC Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MR-J2S B Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSERVO MR-J4-B-LL Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F FX5U Manual de usuario

Mitsubishi Electric

Mitsubishi Electric AE-200A Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F FX5U CPU Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FX2N-10GM Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J5 MR-J5-G Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric TC-24A Manual

Mitsubishi Electric

Mitsubishi Electric EB-50GU-A Manual de instalación

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FX3U-7DM Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario