Mitsubishi Electric MELSEC Q Series Manual de usuario

Analog-Digital Converter Module

User's Manual

-Q64AD

-Q68ADV

-Q68ADI

-GX Configurator-AD (SW2D5C-QADU-E)

A-1 A-1

SAFETY PRECAUTIONS 

(Read these precautions before using this product.)

Before using this product, please read this manual and the relevant manuals carefully and pay full

attention to safety to handle the product correctly.

In this manual, the safety precautions are classified into two levels: " WARNING" and " CAUTION".

Indicates that incorrect handling may cause hazardous conditions,

resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous conditions,

resulting in minor or moderate injury or property damage.

Under some circumstances, failure to observe the precautions given under " CAUTION" may lead to

serious consequences.

Observe the precautions of both levels because they are important for personal and system safety.

Make sure that the end users read this manual and then keep the manual in a safe place for future

reference.

[DESIGN PRECAUTION]

WARNING

Do not write data into "System area" of the buffer memory of intelligent function modules. Also,

do not use any "Use prohibited" signals as an output signal to an intelligent function module

from the programmable controller CPU.

Writing data into "System area" or outputting a signal for "Use prohibited" may cause a

programmable controller system malfunction.

CAUTION

Do not bunch the control wires or communication cables with the main circuit or power wires, or

install them close to each other.

They should be installed 100mm or more from each other.

Not doing so could result in noise that may cause malfunction.

WARNING

CAUTION

A-2 A-2

[SECURITY PRECAUTIONS]

WARNING

To maintain the security (confidentiality, integrity, and availability) of the programmable controller

and the system against unauthorized access, denial-of-service (DoS) attacks, computer viruses,

and other cyberattacks from external devices via the network, take appropriate measures such

as firewalls, virtual private networks (VPNs), and antivirus solutions.

[INSTALLATION PRECAUTIONS]

CAUTION

Use the programmable controller in an environment that meets the general specifications

contained in the user's manual of the CPU module to use.

Using this programmable controller in an environment outside the range of the general

specifications may cause electric shock, fire, malfunction, and damage to or deterioration of the

product.

While pressing the installation lever located at the bottom of module, insert the module fixing tab

into the fixing hole in the base unit until it stops. Then, securely mount the module with the fixing

hole as a supporting point.

Improper installation may result in malfunction, breakdown or the module coming loose and

dropping.

Securely fix the module with screws if it is subject to vibration during use.

Tighten the screws within the range of specified torque.

If the screws are loose, it may cause the module to fallout, short circuits, or malfunction.

If the screws are tightened too much, it may cause damage to the screw and/or the module,

resulting in fallout, short circuits or malfunction.

Be sure to shut off all phases of the external power supply used by the system before mounting

or removing the module.

Not doing so may cause damage to the module.

In the system where a CPU module supporting the online module change is used and on the

MELSECNET/H remote I/O stations, modules can be replaced online (during energizing).

However, there are some restrictions on replaceable modules and the replacement procedures

are predetermined for each module.

For details, refer to the chapter of the online module change in this manual.

Do not directly touch the conductive area or electronic components of the module.

Doing so may cause malfunction or failure in the module.

A-3 A-3

[WIRING PRECAUTIONS]

WARNING

After wiring, attach the included terminal cover to the module before turning it on for operation.

Failure to do so may result in electric shock.

CAUTION

Individually ground the FG terminal of the programmable controller with a ground resistance of

100or less.

Failure to do so may result in electric shock or malfunction.

Use applicable solderless terminals and tighten them within the specified torque range. If any

spade solderless terminal is used, it may be disconnected when a terminal screw comes loose,

resulting in failure.

Tighten the terminal screws within the specified torque range.

Undertightening can cause short circuit, fire, or malfunction.

Overtightening can damage the screw and/or module, resulting in drop, short circuit, or

malfunction.

Be careful not to let foreign matter such as sawdust or wire chips get inside the module.

They may cause fires, failure or malfunction.

The top surface of the module is covered with protective film to prevent foreign objects such as

cable offcuts from entering the module when wiring.

Do not remove this film until the wiring is complete.

Before operating the system, be sure to remove the film to provide adequate ventilation.

A-4 A-4

[STARTING AND MAINTENANCE PRECAUTIONS]

WARNING

Do not touch any terminal while power is on.

Doing so will cause electric shock or malfunction.

Shut off the external power supply (all phases) used in the system before cleaning the module or

retightening the terminal screws or module fixing screws.

Failure to do so may result in electric shock or cause the module to fail or malfunction.

Undertightening can cause drop of the screw, short circuit, or malfunction.

Overtightening can damage the screw and/or module, resulting in drop, short circuit, or

malfunction.

CAUTION

Do not disassemble or modify the modules.

Doing so may cause failure, malfunction, injury, or a fire.

Be sure to shut off all phases of the external power supply used by the system before mounting

or removing the module.

Not doing so may cause failure or malfunction of the module.

In the system where a CPU module supporting the online module change is used and on the

MELSECNET/H remote I/O stations, modules can be replaced online (during energizing).

However, there are some restrictions on replaceable modules and the replacement procedures

are predetermined for each module.

For details, refer to the chapter of the online module change in this manual.

Do not install/remove the module to/from the base unit, or the terminal block to/from the module

more than 50 times after the first use of the product. (IEC 61131-2 compliant)

Failure to do so may cause malfunction.

Always make sure to touch the grounded metal to discharge the electricity charged in the body,

etc., before touching the module.

Failure to do so may cause a failure or malfunctions of the module.

[DISPOSAL PRECAUTIONS]

CAUTION

When disposing of this product, treat it as industrial waste.

A-5 A-5

CONDITIONS OF USE FOR THE PRODUCT 

(1) Mitsubishi programmable controller ("the PRODUCT") shall be used in conditions;

i) where any problem, fault or failure occurring in the PRODUCT, if any, shall not lead to any major or

serious accident; and

ii) where the backup and fail-safe function are systematically or automatically provided outside of the

PRODUCT for the case of any problem, fault or failure occurring in the PRODUCT.

(2) The PRODUCT has been designed and manufactured for the purpose of being used in general

industries.

MITSUBISHI SHALL HAVE NO RESPONSIBILITY OR LIABILITY (INCLUDING, BUT NOT LIMITED

TO ANY AND ALL RESPONSIBILITY OR LIABILITY BASED ON CONTRACT, WARRANTY, TORT,

PRODUCT LIABILITY) FOR ANY INJURY OR DEATH TO PERSONS OR LOSS OR DAMAGE TO

PROPERTY CAUSED BY the PRODUCT THAT ARE OPERATED OR USED IN APPLICATION NOT

INTENDED OR EXCLUDED BY INSTRUCTIONS, PRECAUTIONS, OR WARNING CONTAINED IN

MITSUBISHI'S USER, INSTRUCTION AND/OR SAFETY MANUALS, TECHNICAL BULLETINS AND

GUIDELINES FOR the PRODUCT.

("Prohibited Application")

Prohibited Applications include, but not limited to, the use of the PRODUCT in;

Nuclear Power Plants and any other power plants operated by Power companies, and/or any other

cases in which the public could be affected if any problem or fault occurs in the PRODUCT.

Railway companies or Public service purposes, and/or any other cases in which establishment of a

special quality assurance system is required by the Purchaser or End User.

Aircraft or Aerospace, Medical applications, Train equipment, transport equipment such as Elevator

and Escalator, Incineration and Fuel devices, Vehicles, Manned transportation, Equipment for

Recreation and Amusement, and Safety devices, handling of Nuclear or Hazardous Materials or

Chemicals, Mining and Drilling, and/or other applications where there is a significant risk of injury to

the public or property.

Notwithstanding the above, restrictions Mitsubishi may in its sole discretion, authorize use of the

PRODUCT in one or more of the Prohibited Applications, provided that the usage of the PRODUCT is

limited only for the specific applications agreed to by Mitsubishi and provided further that no special

quality assurance or fail-safe, redundant or other safety features which exceed the general

specifications of the PRODUCTs are required. For details, please contact the Mitsubishi

representative in your region.

(3) Mitsubishi shall have no responsibility or liability for any problems involving programmable controller

trouble and system trouble caused by DoS attacks, unauthorized access, computer viruses, and other

cyberattacks.

A-6 A-6

REVISIONS

The manual number is given on the bottom left of the back cover.

Print Date Manual Number Revision

Dec., 1999 SH (NA)-080055-A First printing

Oct., 2000 SH (NA)-080055-B Add the contents of the function version B.

Correction

bout the Generic Terms and Abbreviations, Section 2.1, Section 3.1.3,

3.4.1, Section 4.3, 4.4.2, Section 5.2.1, 5.2.2, 5.3.3, 5.6.1

Partial addition

Section 1.1, Section 3.1.1, 3.1.2, 3.2, 3.3.1, 3.3.2, Section 4.5, Section

7.2.3, 7.2.4

Addition

Section 1.2, Section 2.2, Appendix 1, 1.1, 1.2, 1.3

Jun., 2001 SH (NA)-080055-C Standardize the name from software package (GPP function) to Product

name (GX Developer).

Standardize the name from utility package (QADU) to Product name (GX

Configurator-AD).

Correction

Conformation to the EMC Directive and Low Voltage Instruction, About

the Generic Terms and Abbreviations, Product Structure, Section 2.1,

2.2, Section 4.6, Section 5.2, 5.2.1, 5.2.2, 5.3.3, Appendix 1.2

Feb., 2002 SH (NA)-080055-D Add the contents of the function version C.

Correction

Section 2.2, Section 3.4.1, Section 4.2, 4.4.1, 4.4.2, Section 5.3.3

Partial addition

SAFETY PRECAUTIONS, , About the Generic Terms and Abbreviations,

Product Structure, Section 1.2, Section 2.1, Section 3.1.1, 3. 2, Section

4.3, 4.6, Section 5.2.1, 5.2.2, Section 8.1, 8.2.1, Appendix 1.1, 1.2, 1.3

Addition

Section 3.4.2, 3.4.3, 3.4.13, 3.4.14, 3.4.15, Chapter 7, Appendix 2, 2.1,

2.2, 2.3

Renumbering

Section 3.4.2 to Section 3.4.10 Section 3.4.4 to Section 3.4.12,

Chapter 7 Chapter 8, Appendix 2 Appendix 3

May, 2002 SH (NA)-080055-E Correction

Section 3.4.1, 3.4.2, 3.4.3, 3.4.14, 3.4.15, Section 4.2, 4.5, 4.6,

Section 7.2, 7.3.1, 7.3.2, 7.3.4, 7.3.6, 7.4, 7.5, Appendix 1.1, 2.2, 2.3

Partial addition

Section 3.3.2, Section 8.2.3

A-7 A-7

The manual number is given on the bottom left of the back cover.

Print Date Manual Number Revision

Feb., 2003 SH (NA)-080055-F Correction

SAFETY PRECAUTIONS, Section 1.2, Section 2.1, Section 3.4.1 to

3.4.3, 3.4.15, Section 4.5, Section 5.1, 5.2.1, 5.2.2, 5.3.2, 5.6.1 to 5.6.3,

Section 7.3.1, 7.3.3 to 7.3.6, Appendix 1.1, Appendix 1.2, Appendix 2.2,

Appendix 2.3

Addition

Section 5.6.4, 5.6.5

May, 2003 SH (NA)-080055-G Correction

Section 2.2, Section 3.4.1, 3.4.2, 3.4.3, 3.4.14, 3.4.15, Section 4.5, 4.6,

Section 5.3.1

May, 2004 SH (NA)-080055-H Addition of program example for use on the remote I/O network.

Correction

Section 2.2, Section 4.6, Chapter 6, Section 7.1, 7.3.1 to 7.3.6

Aug., 2004 SH (NA)-080055-I Correction

Section 1.1, Section 5.1, 5.2.1, 5.2.2, 5.3.1, 5.3.2, 5.3.3, 5.6.1, 5.6.2,

5.6.3, Appendix 2.3

Addition

Section 5.6.4, 5.7, 5.8

Oct., 2004 SH (NA)-080055-J Correction

SAFETY PRECAUTIONS, Section 2.1, Section 3.1.1, Section 4.1,

Section 6.2, 6.2.1

Sep., 2005 SH (NA)-080055-K Correction

SAFETY PRECAUTIONS, Section 2.1, Section 5.2.2, Section 6.2.2,

Feb., 2006 SH (NA)-080055-L Correction

Section 6.1.1, 6.1.2, 6.2.1, 6.2.2, Appendix 2

Jan., 2007 SH (NA)-080055-M Correction

SAFETY PRECAUTIONS, Section 3.3.2, 4.4.2, 4.6, 6.2.1, 6.2.2,

Chapter 7

Jun., 2007 SH (NA)-080055-N Correction

Section 4.3, Appendix 3

Jan., 2008 SH (NA)-080055-O Correction

SAFETY PRECAUTIONS, About the Generic Terms and Abbreviations,

Section 1.2, Section 2.1, 2.3, Section 4.1, 4.5, 4.6, Section 5.2.1, 5.2.2,

5.3.2, 5.3.3, 5.4, 5.6.1, 5.6.5, 5.6.6, Section 6.1.1, 6.2.1, Section 7.3.1,

7.3.3, 7.3.4, 7.3.5, Section 8.1, Appendix 1.1, Appendix 2, Appendix

2.1, Appendix 2.2, Appendix 2.3

Addition

Section 2.2

A-8 A-8

The manual number is given on the bottom left of the back cover.

Print Date Manual Number Revision

May, 2008 SH (NA)-080055-P Correction

SAFETY PRECAUTIONS, Compliance with the EMC and Low Voltage

Directives, About the Generic Terms and Abbreviations, Section 2.1,

Section 3.1.1, 3.1.2, 3.3.2, 3.4.4 to 3.4.6, Section 4.1, Section 5.2.1,

5.2.2, 5.3.1, 5.3.3, Chapter 7, Section 7.1

Nov., 2010 SH (NA)-080055-Q Correction

SAFETY PRECAUTIONS, About Manuals, INTRODUCTION, About the

Generic Terms and Abbreviations,

Section 1.1, Section 2.1, 2.2, 2.3, Section 3.1.1, 3.1.2, 3.3.2,

3.4.1 to 3.4.3, 3.4.5, 3.4.7, 3.4.8, 3.4.10, 3.4.12, Section 4.1, 4.3, 4.4.2,

4.5, 4.6, Section 5.1, 5.2.1, 5.3.1, 5.3.3, 5.4, 5.5, 5.6.1 to 5.6.4, 5.7,

Section 6.2.2, Section 7.1, 7.3.1 to 7.3.6, 7.5, Section 8.1, 8.2.3, 8.2.4,

Appendix 2.1 to Appendix 2.3, Appendix 3

Addition

CONDITIONS OF USE FOR THE PRODUCT

Dec., 2012 SH (NA)-080055-R Correction

SAFETY PRECAUTIONS, COMPLIANCE WITH EMC AND LOW

VOLTAGE DIRECTIVES, ABOUT MANUALS, ABOUT THE GENERIC

TERMS AND ABBREVIATIONS, Section 1.2, Section 2.1,

Section 2.3, Section 3.1.2, 3.2.2, 3.3.1, 3.4.6, 3.4.7, 3.4.8, 3.4.10,

3.4.11, 3.4.15, Section 4.1, 4.6, Section 5.2.2, 5.6.1 to 5.6.4,

Section 6.1, 6.2, 6.2.2, Chapter 7, Section 7.3.4, 7.4, 7.5, Section 8.1,

8.2.3

May, 2015 SH (NA)-080055-S Correction

ABOUT THE GENERIC TERMS AND ABBREVIATIONS, Section 2.1,

2.3, Section 4.3, 4.6, Section 5.2.1, 5.6.2, 5.6.3, Section 6.1.2,

Appendix 3

Jan., 2021 SH (NA)-080055-T Correction

SAFETY PRECAUTIONS, CONDITIONS OF USE FOR THE PRODUCT,

PRODUCT STRUCTURE, Section 8.1

Japanese Manual Version SH-080028-Y

This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent

licenses. Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property

rights which may occur as a result of using the contents noted in this manual.

1999 MITSUBISHI ELECTRIC CORPORATION

Otros manuales para MELSEC Q Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de control de Mitsubishi Electric

Mitsubishi Electric

Mitsubishi Electric ACH1 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric RD81DL96 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FR-A7NL Guía de configuración

Mitsubishi Electric

Mitsubishi Electric NZ2GN2S1-32D Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q173HCPU Manual del propietario

Mitsubishi Electric

Mitsubishi Electric QD75P1N Manual de usuario

Mitsubishi Electric

Mitsubishi Electric AJ65FBTA2-16TEU Manual de usuario

Mitsubishi Electric

Mitsubishi Electric AJ65BT-68TD Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric A1SD75P1-S3 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GT16H-CNB-42S Manual de usuario

Mitsubishi Electric

Mitsubishi Electric AJ65FBTA42-16DT Manual de usuario

Mitsubishi Electric

Mitsubishi Electric EMU4-CNT-MB Manual de usuario

Mitsubishi Electric

Mitsubishi Electric NZ2GF2B-60TCTT4 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GT1695M-XTBA Instrucciones de funcionamiento y mantenimiento

Mitsubishi Electric

Mitsubishi Electric NZ2FTGN Manual de usuario

Mitsubishi Electric

Mitsubishi Electric EMU4-CNT-MB Manual de usuario

Mitsubishi Electric

Mitsubishi Electric AJ65SBTB2N-16S Manual de usuario

Mitsubishi Electric

Mitsubishi Electric AJ65DBTB1-32D Manual de usuario

Mitsubishi Electric

Mitsubishi Electric WS0-CPU000200 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC-L LD75P Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GT1020-LBD Instrucciones de funcionamiento y mantenimiento

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric QJ71MT91 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario