Mitsubishi Electric FR-PU04 Manual de usuario

FR-PU04/FR-PU04V INSTRUCTION MANUAL

INVERTER

Option unit

INSTRUCTION MANUAL

INVERTER

HEAD OFFICE: TOKYO BUILDING 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN

FR-PU04

FR-PU04V

Parameter unit

STOP

RESET

1 2 3

456

789

EXT

SETMON

ESCHELP SHIFT

FWD

REV

WRITE

READ

PARAMETER UNIT

STF FWD PU

FR-PU04

IB(NA)-0600637ENG-A(1604) MEE Printed in Japan Specifications subject to change without notice.

PRE-OPERATION

INSTRUCTIONS

FUNCTIONS

HELP

OPERATION

SPECIFICATIONS

CHECK FIRST WHEN YOU

HAVE A TROUBLE

A-1

Thank you for choosing the Mitsubishi inverter option unit.

This instruction manual gives handling information and

precautions for use of this equipment. Incorrect handling might

cause an unexpected fault. Before using the equipment, please

read this manual carefully to use the equipment to its optimum.

Please forward this manual to the end user.

1. Electric Shock Prevention

This section is specifically about

safety matters

Do not attempt to install, operate, maintain or inspect this

product until you have read through this instruction manual and

appended documents carefully and can use the equipment

correctly. Do not use this product until you have a full knowledge

of the equipment, safety information and instructions.

In this instruction manual, the safety instruction levels are

classified into "WARNING" and "CAUTION".

Assumes that incorrect handling

may cause hazardous conditions,

resulting in death or severe injury.

Assumes that incorrect handling

may cause hazardous conditions,

resulting in medium or slight injury,

or may cause physical damage only.

Note that the CAUTION level may lead to a serious

consequence according to conditions. Please follow the

instructions of both levels because they are important to

personnel safety.

WARNING

CAUTION

SAFETY INSTRUCTIONS

WARNING

While the inverter power is ON, do not open the front cover. Do

not run the inverter with the front cover removed.

Otherwise you may access the exposed high voltage terminals

or the charging part of the circuitry and get an electric shock.

Before starting wiring or inspection, check that the operation

panel indicator is OFF, wait for at least 10 minutes after the

power supply has been switched OFF, and check that there are

no residual voltage using a tester or the like. The capacitor is

charged with high voltage for some time after power OFF and it

is dangerous.

Any person who is involved in the wiring or inspection of this

equipment should be fully competent to do the work.

Always install the inverter before wiring. Otherwise, you may

get an electric shock or be injured.

Operate the keys with dry hands to prevent an electric shock.

A-2

2. Additional Instructions

To prevent injury, damage or product failure, please note the

following points.

(1) Transportation and mounting

(2) Test operation and adjustment

(3) Usage

(4) Corrective actions for alarm

CAUTION

Do not install and operate the parameter unit (FR-PU04/PU04V)

if it is damaged or has parts missing.

Do not stand or rest heavy objects on this equipment.

Check the inverter mounting orientation is correct.

The parameter unit (FR-PU04/PU04V) is a precision device. Do

not drop it or subject it to impact.



Use the inverter under the following environmental conditions:

*Temperatures applicable for a short time, e.g. in transit.



If halogen-based materials (fluorine, chlorine, bromine, iodine,

etc.) infiltrate into a Mitsubishi product, the product will be

damaged. Halogen-based materials are often included in

fumigant, which is used to sterilize or disinfest wooden packages.

When packaging, prevent residual fumigant components from

being infiltrated into Mitsubishi products, or use an alternative

sterilization or disinfection method (heat disinfection, etc.) for

packaging. Sterilization of disinfection of wooden package should

also be performed before packaging the product.

Environment

Surrounding air

temperature -10Cto +50C (non-freezing)

Ambient

humidity 90%RH or less (non-condensing)

Storage

temperature -20C to +65C*

Ambience Indoors (free from corrosive gas,

flammable gas, oil mist, dust and dirt)

Altitude,

vibration

Maximum 1000m above seal level,

5.9m/s2or less at 10 to 55Hz (directions

of X, Y, Z axes)

CAUTION

Before starting operation, confirm and adjust the parameters.

A failure to do so may cause some machines to make

unexpected motions.

WARNING

Since pressing key may not stop output depending on

the function setting status, provide a circuit and switch

separately to make an emergency stop (power OFF,

mechanical brake operation for emergency stop, etc).



Make sure that the start signal is off before resetting the inverter

alarm. A failure to do so may restart the motor suddenly.

Do not modify the equipment.

Do not perform parts removal which is not instructed in this

manual. Doing so may lead to fault or damage of the inverter.

CAUTION

When parameter clear or all parameter clear is performed, each

parameter returns to the factory setting. Re-set the required

parameters before starting operation.

CAUTION

Provide safety backup devices, such as an emergency brake,

to protect machines and equipment from hazard if the

parameter unit (FR-PU04/PU04V) becomes faulty.

A-3

(5) Disposal

(6) General instruction

CAUTION

Treat as industrial waste.

All illustrations given in this manual may have been drawn with

covers or safety guards removed to provide in-depth description.

Before starting operation of the product, always return the covers

and guards into original positions as specified and operate the

equipment in accordance with the manual.

— CONTENTS —

INTRODUCTION 1

1 PRE-OPERATION INSTRUCTIONS 3

1.1 Unpacking and Product Confirmation .............................................................................................3

1.1.1 Unpacking confirmation .................................................................................................................................. 3

1.1.2 Appearance and parts identification ............................................................................................................... 4

1.1.3 Explanation of keys ........................................................................................................................................5

1.2 Installation and Removal of FR-PU04/PU04V..................................................................................7

1.2.1 Direct installation to the inverter .....................................................................................................................7

1.2.2 Removal from the inverter .............................................................................................................................. 8

1.2.3 Installation using the connection cable (FR-CB2) ..........................................................................................9

1.2.4 Removal when the connection cable (FR-CB2) is used...............................................................................10

1.3 Parameters to be Checked First.....................................................................................................11

1.3.1 PU display language selection (Pr. 145) ...................................................................................................... 11

1.3.2 PU buzzer control (Pr. 990) .......................................................................................................................... 12

1.3.3 PU contrast adjustment (Pr. 991) .................................................................................................................12

2 FUNCTIONS 13

2.1 Monitoring Function ........................................................................................................................13

2.1.1 Display overview...........................................................................................................................................13

2.1.2 Using "SHIFT" to change the main monitor.................................................................................................. 15

2.1.3 Setting the power-ON monitor (the first priority monitor) ..............................................................................16

2.1.4 Using "READ" to change the main monitor ..................................................................................................17

2.1.5 Using the parameter to change the monitor (Pr. 52) ....................................................................................18

2.2 Frequency Setting............................................................................................................................20

2.2.1 Direct setting.................................................................................................................................................20

2.2.2 Step setting................................................................................................................................................... 21

2.2.3 Precautions for frequency setting.................................................................................................................22

2.3 Setting and Changing the Parameter Values ................................................................................23

2.3.1 Specifying the parameter number to change the set value ..........................................................................23

2.3.2 Selecting the parameter from functional list to change the set value ...........................................................24

2.3.3 Selecting the parameter from parameter list to change the set value ..........................................................26

2.3.4 Selecting the parameter from User List to change the set value..................................................................27

2.3.5 Precautions for setting write .........................................................................................................................28

2.4 User Group Function .......................................................................................................................29

2.4.1 Registering the parameters to user group ....................................................................................................30

2.4.2 Deleting the parameters from user group..................................................................................................... 31

2.4.3 Confirming the parameters registered to user group.................................................................................... 31

2.5 Calibration of the Meter (Frequency Meter)...................................................................................32

2.5.1 Calibration of the FM terminal ...................................................................................................................... 32

2.5.2 Calibration of the AM terminal ..................................................................................................................... 33

2.6 Adjustment of the Frequency Setting Signals "Bias" and "Gain" ..............................................36

2.6.1 Adjustment procedure .................................................................................................................................. 36

3HELP 42

III

3.1 Overview of the Help Menu .............................................................................................................42

3.1.1 Help menu ....................................................................................................................................................42

3.1.2 Help menu transition.....................................................................................................................................44

3.2 Operation Procedures for the Help Menu......................................................................................48

3.2.1 Monitor function ............................................................................................................................................ 48

3.2.2 Selection of PU operation (direct input)........................................................................................................49

3.2.3 Selection of the PU Jog operation mode ...................................................................................................... 50

3.2.4 Parameters ................................................................................................................................................... 51

3.2.5 Parameter clear ............................................................................................................................................54

3.2.6 Alarm history................................................................................................................................................. 56

3.2.7 Alarm clear ................................................................................................................................................... 57

3.2.8 Inverter reset ................................................................................................................................................ 58

3.2.9 Troubleshooting............................................................................................................................................59

3.2.10 Terminal assignment (Selectop)...................................................................................................................63

3.2.11 Option...........................................................................................................................................................64

3.2.12 Multiple copies.............................................................................................................................................. 65

3.3 Other Precautions............................................................................................................................70

3.3.1 Precautions for parameter unit operation ....................................................................................................70

4 OPERATION 71

4.1 How to Select the Operation Mode.................................................................................................71

4.1.1 Switching from External operation mode [EXT] to PU operation mode [PU]................................................71

4.1.2 Switching from PU operation mode [PU] to External operation mode [EXT]................................................71

4.1.3 Switching to the External / PU combined operation mode ........................................................................... 72

4.2 How to Operate PU Operation ........................................................................................................74

4.2.1 Normal operation ..........................................................................................................................................74

4.2.2 PU Jog operation..........................................................................................................................................75

4.3 Combined Operation (Operation Using External Input Signals and PU)....................................76

4.3.1 Entering the start signal from outside and setting the running frequency from the PU (Pr. 79 = 3) .............76

4.3.2 Entering the running frequency from outside and making start and stop from the PU (Pr. 79 = 4)..............77

4.3.3 Entering the start signal and multi-speed signal from outside and

setting multiple speeds from the parameter unit...........................................................................................78

5 CHECK FIRST WHEN YOU HAVE A TROUBLE 79

5.1 Troubleshooting...............................................................................................................................79

6 SPECIFICATIONS 80

6.1 Standard Specifications ..................................................................................................................80

6.2 Outline Drawing and Panel Cutting Drawing.................................................................................81

6.2.1 FR-PU04/PU04V outline dimension drawings..............................................................................................81

6.2.2 FR-PU04/PU04V enclosure cut dimensions................................................................................................. 82

APPENDIX 83

Appendix 1 Disposing of the equipment in the EU countries ..............................................................83

INTRODUCTION

This product is a unit for setting inverter functions (parameters) and has the following features.

· An operation panel can be removed and a parameter unit can be connected.

· Setting such as direct input method with a numeric keypad, operation status indication, and help function are

usable.

· Eight languages can be displayed.

· Parameter setting values of maximum of three inverters can be stored.

INTRODUCTION

This instruction manual uses the screens on the FR-PU04 connected to the FR-A500 series inverter for

describing the operation.

For using the FR-PU04V, some indications or terms used in this instruction manual must be replaced as

follows.

Item FR-PU04 FR-PU04V

Name Frequency, output frequency Speed, running speed

Main monitor indication 60.00Hz 1500.0r

First monitor Frequency Speed

Monitor indication F Command S Command

Appearance

Rating plate

Term i n a l FM DA1

AM DA2

STOP

RESET

1 2 3

456

789

EXT

SETMON

ESCHELP SHIFT

FWD

REV

WRITE

READ

PARAMETER UNIT

STF FWD PU

FR-PU04

HELP

123

456

789

EXT

SETMON

ESC

SHIFT

FWD

REV

WRITE

READ

STF FWD PU

FR-PU04V

PARAMETER UNIT

RESET

STOP

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de control de Mitsubishi Electric

Mitsubishi Electric

Mitsubishi Electric FR-A7NL Guía de configuración

Mitsubishi Electric

Mitsubishi Electric 800 Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric AJ65VBTCE32-16DT Manual de usuario

Mitsubishi Electric

Mitsubishi Electric NZ2GN2S1-32D Manual de usuario

Mitsubishi Electric

Mitsubishi Electric A1S68DAV Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Apricot Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PSS**S72FT Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-R Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GOT1000 GT1595-XTBA Instrucciones de funcionamiento y mantenimiento

Mitsubishi Electric

Mitsubishi Electric AJ65VBTS32-16DT Manual de usuario

Mitsubishi Electric

Mitsubishi Electric WD8700U Manual de usuario

Mitsubishi Electric

Mitsubishi Electric RD81RC96-CA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Trane TE-200A Manual de usuario

Mitsubishi Electric

Mitsubishi Electric NZ2GF2B-60TCTT4 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GT1020-LBD Instrucciones de funcionamiento y mantenimiento

Mitsubishi Electric

Mitsubishi Electric EMU4-CNT-MB Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC Q Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-F FX5 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PSSxxMC1Fx Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FX-USB-AW Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSEC iQ-RX40NC6B Manual de usuario

Mitsubishi Electric

Mitsubishi Electric A1SD75P1-S3 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario