Mindray DPM 6 Manual de usuario

Quick Reference Guide

Note: The DPM 6 and DPM 7 Quick Reference Guide

is not intended as a replacement to the Operating

Instructions. Prior to operating equipment, the user

must be familiar with the Operating Instructions

Manual contents. This document is a guideline only to

be used as an aid to comprehensive Inservice Training.

Patient Setup ..................................................1

Enter Demographics ............................................1

Adjust Patient Size ..............................................1

Discharge a Patient ............................................. 2

Standby .......................................................2

Enter Standby ..................................................2

Resume Monitoring.............................................2

Record.........................................................3

Real-Time Waveforms ...........................................3

Adjust Recorder’s Waveforms.................................... 3

Print ...........................................................3

Real-Time Waveforms ...........................................3

ECG............................................................4

Adjust ECG Lead ................................................4

Enable Pacemaker Detection And Set Pacemaker Rate ...........4

Initiate Relearn ................................................. 5

Initiate ST Analysis ..............................................5

NIBP ...........................................................5

Initiate a Non-Invasive Blood Pressure Measurement (NIBP) ..............5

Set a Non-Invasive Blood Pressure Measurement Interval ...............5

Invasive Blood Pressures........................................6

Adjust Invasive Blood Pressure Label ............................ 6

Zero Invasive Blood Pressure .................................... 7

Alarms.........................................................7

Adjust Alarm Limits ............................................. 7

Adjust Alarm Responses ........................................ 8

Adjust Arrhythmia Alarms....................................... 9

Disable Non-Lethal Arrhythmias.................................9

Table of Contents

P/N: 046-003757-00 Rev A

Silence Alarms ............................................... 10

Silence All Alarms ............................................ 10

Transfer...................................................... 10

Hemodynamic Monitoring.................................... 11

Initiate a Cardiac Output Measurement.........................11

Initiate Pulmonary Artery Wedge Pressure (PAWP) ..............12

Initiate Hemodynamic Calculations.............................13

Screen Display ............................................... 14

History ...................................................... 15

Tabular Trends .................................................15

Arrhythmia And Alarm Events ..................................16

Full Disclosure .................................................16

Volumes ..................................................... 17

Key Volume....................................................17

Beat Tone......................................................18

Date And Time ............................................... 18

Parameter Colors............................................. 19

Default (Preset) Settings ...................................... 19

Table of Contents (cont'd)

P/N: 046-003757-00 Rev A

Quick Key Description

Scroll left to display more

QuickKeys

Scroll right to display more

QuickKeys

Enter the main menu

Enter standby mode

Change alarm settings

Review the patient's data

Enter the NIBP measurement

Stop all NIBP measurement

Start NIBP STAT measurement

Zero IBP

Change screen

Enter the patient setup menu

Trigger a manual event

Default configurations

Start cardiac output

procedure

Blank

Start the real-time print

Print Setup

Have a split-screen view of

minitrend

Enter the volume setup

View respiratory loops

Perform calculations

Have a split-screen view of

another patient's conditions

Have a split-screen view of

OxyCRG trends

Enter the CPB mode

Enter the PAWP

measurement screen

Enter the full-screen 7-lead

ECG screen

Enter the [Parameters] menu

P/N: 046-003757-00 Rev A

Quick Reference Guide

PATIENT SETUP

Enter Demographics

The Patient Setup menu allows the clinician to enter and modify patient

demographics.

To enter demographics at DPM 6 or DPM 7 bedside monitor:

a. Access Patient Setup menu using Patient Setup (quick key) or

Main Menu (quick key)

b. Select Patient Demographics

c. Select white edit box to open field and enter patient information

d. Enter patient’s information using onscreen keyboard

e. Select ENTER to accept the information

f. Select OK to return to main display

Panorama® Central Station Interface: Entering demographic information at

the Panorama® Central Station or WorkStation automatically enters it at the

bedside monitor. Entering demographic information at the bedside monitor

automatically enters it at the Panorama® Central Station and WorkStation.

Admit is not required for patient information to be displayed or stored.

Adjust Patient Size

The Patient Setup menu allows the clinician to adjust patient size. To adjust

patient size on the DPM 6 or DPM 7 bedside monitor:

a. Access Patient Setup menu using Patient Setup (quick key) or

Main Menu (quick key)

b. Select Patient Demographics

c. Select Patient Cat.

d. Select current size and adjust to Adu (adult), Ped (pediatric), or Neo

(Neonate)

e. Select OK to return to main display

Note: Adjusting patient size restores the monitor to the default

(preconfigured) settings but does not clear patient information or data.

Panorama® Central Station: Patient size cannot be changed from the

Panorama® Central Station

P/N: 046-003757-00 Rev A

Quick Reference Guide

Discharge A Patient

The Discharge function clears all patient information and restores default

(preconfigured) settings.

To Discharge a patient from the DPM 6 or DPM 7 bedside monitor:

a. Access Patient Setup menu using Patient Setup (quick key) or

Main Menu (quick key)

b. Select Discharge Patient

c. Select OK to confirm

Note: After the patient is discharged, default (preconfigured) settings are

restored, and the monitor is placed in Standby.

Panorama® Central Station Interface: Discharging a patient from the DPM 6

or DPM 7 bedside monitor will automatically discharge the patient from the

Panorama® Central Station, WorkStation, and ViewStation. Discharging the

patient on the Panorama® Central Station will discharge the patient from the

WorkStation, ViewStation, and DPM 6 or DPM 7 bedside monitor (optional).

STANDBY

Enter Standby

The Standby function allows the clinician to suspend monitoring on a patient.

While in standby, the patient is not monitored; however, all data and settings

are preserved.

To place a patient into Standby on the DPM 6 or DPM 7 bedside monitor:

a. Select the STANDBY (quick key)

b. Select Yes to confirm

Resume Monitoring

To remove a patient from Standby and resume monitoring on the DPM 6 or

DPM 7 bedside monitor:

a. Select any key on the DPM 6 or DPM 7 bedside monitor

Panorama® Central Station Interface: Placing a patient in standby at the

DPM 6 or DPM 7 bedside monitor will automatically place the Panorama®

Central Station, WorkStation, and ViewStation in standby. Selecting Bedside

and Panorama® Standby on the Panorama® Central Station or WorkStation

P/N: 046-003757-00 Rev A

Quick Reference Guide

automatically places the bedside monitor and ViewStation in standby. Select

any key on the front panel or select the display to remove patient from

Standby on the DPM 6 or DPM 7 bedside monitor.

Note: A patient cannot be removed from Standby from the Central Station.

The patient must be removed from Standby at the DPM 6 or DPM 7 bedside

monitor.

RECORD

Real-Time Waveforms

To record a strip on a patient at the DPM 6 or DPM 7 bedside monitor's

integrated recorder:

a. Select REC on the monitor’s front keypad

Adjust Recorder’s Waveforms

To adjust the waveforms recorded on a patient at the DPM 6 or DPM 7 bedside

monitor's integrated recorder:

a. Main Menu (quick key)

b. Select Record Setup menu

c. Select Waveform 1, Waveform 2, or Waveform 3

d. Select the waveforms for recording from drop down list or select off to

turn off waveform recording

e. Select Main Menu (quick key) or to return to the main display

Real-Time Waveforms

To print a strip on a patient at the DPM 6 or DPM 7 bedside monitor to a

predetermined laser printer:

a. Select Real-Time Print (quick key)

Panorama® Central Station interface: Selecting Real-Time Print at the DPM 6 or

DPM 7 bedside monitor will print a 10-second, All Strips Report on the Panorama®

Central Station. The waveforms printed are determined by the Print Setup tab

at the Panorama® Central Station. Waveform print selection on the Panorama®

Central Station, WorkStation, and ViewStation are independent.

P/N: 046-003757-00 Rev A

Quick Reference Guide

ECG

Adjust ECG Lead

The DPM 6 and DPM 7 allow the clinician to adjust the leads being viewed on

the main display. To adjust the ECG Lead:

a. Select ECG waveform or ECG numeric tile to enter the ECG Setup menu

a. Select ECG setup>> from the Parameters menu in Main Menu

(quick key) to enter the ECG Setup menu

b. Select ECG1 current lead to adjust the first lead or ECG2 current lead to

adjust the second lead

c. Scroll and select lead

d. Select Main Menu (quick key) or to return to the main display

Panorama® Central Station Interface: Adjusting ECG leads on the DPM 6

or DPM 7 bedside monitor, Panorama® Central Station, WorkStation, and

ViewStation are independent.

Enable Pacemaker Detection And Set Pacemaker Rate

The DPM 6 and DPM 7 allow the clinician to enable pacemaker detection.

The symbol is displayed when the pacemaker detection is enabled.

To enable the pacemaker detection on the DPM 6 or DPM 7 bedside monitor:

a. Select ECG waveform or ECG numeric tile to enter the ECG Setup menu

a. Select ECG setup>> from the Parameter menu in Main Menu

(quick key) to enter the ECG Setup menu

b. Select Others >>

c. Select Paced to Yes

d. Select Pacemaker Rate value and adjust using the up and down arrows

e. Select Main Menu (quick key) or to return to the main display

Panorama® Central Station Interface: Pacemaker detection on the DPM 6 or

DPM 7 monitor, Panorama® Central Station, WorkStation, and ViewStation are

independent.

Otros manuales para DPM 6

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo médico de Mindray

Mindray

Mindray M6 Manual de usuario

Mindray

Mindray DC-3 Manual de usuario

Mindray

Mindray M7 Manual de usuario

Mindray

Mindray V Series Manual de usuario

Mindray

Mindray MR6401 Manual de usuario

Mindray

Mindray TE7 Manual de usuario

Mindray

Mindray BeneVision N Series 22 N1 Manual de usuario

Mindray

Mindray Accutorr 7 Manual de usuario

Mindray

Mindray M6Vet Manual de usuario

Mindray

Mindray M5 Manual de usuario

Mindray

Mindray BeneHeart D3 Manual de usuario

Mindray

Mindray TE7T Manual de usuario

Mindray

Mindray Z6 Pro Manual de usuario

Mindray

Mindray BP10 NIBP Module Manual de usuario

Mindray

Mindray A7 Manual de usuario

Mindray

Mindray SynoVent E5 Manual de usuario

Mindray

Mindray BeneHeart C Series Manual de usuario

Mindray

Mindray BeneHeart D30 Manual de usuario

Mindray

Mindray Resona I9W Manual de usuario

Mindray

Mindray 35C50EB Manual de usuario

Mindray

Mindray dpm 3 Manual de usuario

Mindray

Mindray DC-T6 Manual de usuario

Mindray

Mindray SV Series Manual de usuario

Mindray

Mindray DP-8500 Manual de usuario

Manuales populares de Equipo médico de otras marcas

TekTone

TekTone Tek-CARE160 Manual de usuario

NeuroMetrix

NeuroMetrix Quell 2.0 Manual de usuario

AMT

AMT XLR8 Manual de usuario

Medipost-Nutristoma

Medipost-Nutristoma MD300K2 Manual de usuario

EDAN

EDAN SONOTRAX Pro Manual de usuario

Restorative Therapies

Restorative Therapies RT300 Manual de usuario

Gendex

Gendex Expert DC Manual de usuario

Dexcowin

Dexcowin ADX4000W Manual de usuario

Libelium

Libelium MySignals Manual de usuario

Acelity

Acelity V.A.C.ULTA 4 Manual de usuario

Caputron

Caputron ActivaDose II tDCS Manual de usuario

FujiFilm

FujiFilm Sonart Manual del propietario

Plinth 2000

Plinth 2000 93CDT Manual de usuario

GE SENOGRAPHE 800T Manual de usuario

GE Definium 5000 Manual de usuario

Kanmed

Kanmed GE-1380 Manual de usuario

Huntleigh

Huntleigh FD1 Manual de usuario

Stryker

Stryker SPR Plus Manual de usuario