Milwaukee CD97 Manual de usuario

USER MANUAL

CD97

Digital

Low Range TDS Pen

SPECIFICATIONS

RANGE 0 to 999 ppm

RESOLUTION 1 ppm

ACCURACY

(@20°C) ±10 ppm

TYPICAL

EMC DEVIATION ± 1 % Full Scale

TEMPERATURE

COMPENSATION

Automatic from

5 to 50ºC

ENVIRONMENT 5 to 50°C

95 % RH max.

BATTERY TYPE 4 x 1.5V alkaline

BATTERY LIFE

approximately

300hours of use

DIMENSIONS 150 x 30 x 24 mm

WEIGHT 85 g

OPTIONAL ACCESSORIES

MA9300 1.5V battery (10pcs.)

MA9701 Calibration Screwdrivers

(20pcs)

M10080B

Calibration 20mL sachet

800ppm solution

(25pcs.)

Milwaukee Instruments reserves the

right to make improvements in design,

construction and appearance of its

products without advance notice.

CERTIFICATION

Milwaukee Instruments

conform to the CEEuropean

Directives.

Disposal of Electrical &

Electronic Equipment. Do

not treat this product as household

waste. Hand it over to the appropriate

collection point for the recycling of

electrical and electronic equipment.

Disposal of waste

batteries. This product

contains batteries. Do not

dispose of them with other household

waste. Hand them over to the appropriate

collection point for recycling.

Please note: proper product and

battery disposal prevents potential

negative consequences for human

health and the environment. For

detailed information, contact your local

household waste disposal service or go to

www.milwaukeeinstruments.com (USA

& CAN) or www.milwaukeeinst.com.

WARRANTY

This instrument is warranted against

defects in materials and manufacturing

for a period of 2 years from the date

of purchase. Probe is warranted for

6 months. This warranty is limited to

repair or free of charge replacement if the

instrument cannot be repaired. Damage

due to accidents, misuse, tampering

or lack of prescribed maintenance is

not covered by warranty. If service is

required, contact your local Milwaukee

Instruments Technical Service. If the

repair is not covered by the warranty, you

will be notified of the charges incurred.

When shipping any instrument, make

sure it is properly packaged for complete

protection.

ISTCD97 11/20

SATISFACTION

GUARANTEED

888

CD97

Distributor in AustraliaPacific Sensor Technologies Pty LtdUnit 4, 3 Neutron Place Rowville, VIC 3178 Australia1300 662 720 | [email protected]www.pacificsensortech.com.au

888

CD97

RANGE

0 / 999

ppm

FRONT

ON/OFF

SWITCH

LIQUID

CRYSTAL

DISPLAY

MAXIMUM

IMMERSION

LEVEL

MINIMUM

IMMERSION

LEVEL

SENSING

PROBES

BATTERY

COMPARTMENT

CALIBRATION

TRIMMER

POCKET

CLIP

BACK

OPERATION

yRemove the protective cap.

yTurn the digital pen on with the

ON/OFF switch located on the top.

000

CD97

yImmerse into solution up to the

maximum immersion level.

yStir gently and wait until the display

stabilizes. CD97 compensates for the

temperature variance automatically.

yRead the value on the display.

CALIBRATION

yThe calibration procedure is very

simple and fast.

yImmerse the pen up to the maximum

level into the appropriate optional

Calibration Solution M10080B

correspondig to 800ppm.

yAllow the reading to stabilize.

yBy turning the calibration trimmer

with a small screwdriver adjust the

reading to match the solution value

of 800ppm (normally to the value at

25°C).

800

600

yCalibration is now complete.

BATTERY REPLACEMENT

When the CD97 cannot be switched

on or the display fades, pull out the

battery compartment and replace all

four 1.5V batteries, paying attention

to their polarity. Batteries should only

be replaced in a non‑hazardous area

using the battery types specified in this

instruction manual.

CD97

RECOMMENDATION

Before using this product, makesure that

it is entirely suitable for the environment

in which they are used. Operation of

these instruments in residential areas

could cause unacceptable interferences

to radio and T.V. equipment. The pins at

the end of the sensor are sensitive to

electrostatic discharges. Avoid touching

this metal band at all times. During

operation of instruments ESD wrist

straps should be worn to avoid possible

damage to the sensor by electrostatic

discharge. Any variation introduced

by the user to the supplied equipment

may degrade the instrument EMC

performance. To avoid electrical shock,

do not use the instrument when voltage

at the measurement surface exceed

24VAC or 60VDC. To avoid damages or

burns, do not perform any measurement

in microwave ovens.

Otros manuales de Instrumento de medición de Milwaukee

Milwaukee

Milwaukee MW105 MAX Manual de usuario

Milwaukee

Milwaukee LDM 45 Manual de usuario

Milwaukee

Milwaukee 2205-20 Manual de usuario

Milwaukee

Milwaukee MW150 Manual de usuario

Milwaukee

Milwaukee M12 3632-20 Manual de usuario

Milwaukee

Milwaukee PRO MI415 Manual de usuario

Milwaukee

Milwaukee MI 413 Manual de usuario

Milwaukee

Milwaukee MW10 Manual de usuario

Milwaukee

Milwaukee MW301 Manual de usuario

Milwaukee

Milwaukee 2205-40 Manual de usuario

Milwaukee

Milwaukee MI 806 Manual de usuario

Milwaukee

Milwaukee MW11 Manual de usuario

Milwaukee

Milwaukee PH55 Manual de usuario

Milwaukee

Milwaukee 2235-40 Manual de usuario

Milwaukee

Milwaukee LRD100 Manual de usuario

Milwaukee

Milwaukee REDLITHIUM L4 CLL, REDLITHIUM L4 CPL Manual de usuario

Milwaukee

Milwaukee 3712 Manual de usuario

Milwaukee

Milwaukee C12 CMH Manual de usuario

Milwaukee

Milwaukee MC510 Manual de usuario

Milwaukee

Milwaukee MI411 Manual de usuario

Milwaukee

Milwaukee MW100 Manual de usuario

Milwaukee

Milwaukee MW801 Manual de usuario

Milwaukee

Milwaukee MW11 Manual de usuario

Milwaukee

Milwaukee REDLITHIUM Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario