Miele KWT 1601 SF Manual de usuario

Operating and Installation

Instructions

Wine Storage Unit

KWT 1601 SF

KWT 1611 SF

To prevent accidents

and machine damage

read these instructions

before

installation or use. M.-Nr. 07 360 860

en - US, CA

Installation instructions

To prevent accidents

and machine damage

read these instructions

before

installation or use.

Disposal of packing materials

The cardboard box and packing

materials are biodegradable and

recyclable. Please recycle.

Ensure that any plastic wrappings,

bags, etc., are disposed of safely and

kept out of the reach of babies and

young children. Danger of suffocation!

Disposal of an old appliance

Old appliances contain materials that

can be recycled. Please contact your

local recycling center about the

possibility of recycling these materials.

Before discarding an old appliance,

disconnect it from the gas and

electrical supply and cut off the power

cord to prevent it from becoming a

hazard.

Caring for the environment

,In areas with a tropical climate

(over 100°F/38°C and more than

70% air humidity) the wine cooler

must only be operated in air

conditioned locations. Otherwise the

function of the machine cannot be

guaranteed.

Have the appliance installed by a

qualified technician, according to

the enclosed installation instructions.

The manufacturer is not liable for

damage to property due to an

incorrect installation.

,WARNING

This appliance is top-heavy and

must be secured to prevent the

possibility of tipping forward.

Anti-tip protection is required.

Keep the door closed until the

appliance is completely installed

and secured as per the installation

instructions.

Empty weight of your machine:

KWT 16X1 SF ......337lbs(153 kg)

Installation site

The appliance should be installed in a

dry, well ventilated room.

Do not install the appliance:

- outdoors,

- in an environment with dripping

water,

- in rooms which are at risk of frost.

The installation location should not be

exposed to direct sunlight, nor near a

heat source, such as an oven,

radiator, etc.

The ambient temperature should not

drop below 55 °F (13 °C) or rise above

110 °F (43 °C), otherwise malfunctions

may occur.

If installation next to a heat source is

unavoidable, use a suitable insulating

plate or observe the following minimum

distances from the heat source:

–1

1/4" (3 cm) from an electric cooktop

or oven.

–12" (30 cm) from a gas cooktop or

oven.

Installation

Base

A fully loaded appliance is very heavy.

The load-bearing capacity of your floor

must meet the following requirements:

KWT 16x1 SF ........805lbs(365 kg)

To ensure that the appliance is installed

securely and functions properly, the

base must be flat, level and made of a

hard, rigid material.

If in doubt, contact Miele.

Furniture/fixtures

The new appliance will be mounted

securely to adjacent and overhead

furniture/fixtures.

For this reason it is essential that all

attachable furniture/fixtures are

connected securely to the base or the

wall by suitable means.

Ventilation

The air intake and outlet must not be

blocked or covered in any way. They

also need to be dusted/cleaned on a

regular basis.

Installation niche

To ensure safe, trouble-free installation

and the best possible cosmetic result,

check to be sure that the installation

space complies with the installation

dimensions. See "Niche dimensions".

The side walls of the installation cavity

must be plumb.

The minimum thickness of the side

walls and the top wall must be 5/8"

(16 mm).

The minimum thickness of the toe-kick

panel must be ½" (13 mm). A thickness

of 3/4" (19 mm) is recommended.

Installation

Installation options

There are many different installation

options. You are limited only by the

design of the kitchen.

The door hinge cannot be

exchanged.

Single column

The appliance can be installed at any

preferred location in the kitchen.

However, be sure the door will open

and close properly in the chosen

location.

Side-by-side

This appliance can be installed

'side-by-side" with another

fridge/freezer using a "Merging kit".

The "Merging Kit" can be obtained from

Miele.

Contact Miele or your dealer for

specific information about which

combinations will work with your

appliance.

. . . without partition

If the appliances are installed directly

next to each other (without a partition),

they will need to be attached together.

A heating mat must also be installed.

This will help avoid condensation and

prevent damage.

For instructions on how to attach the

appliances and install the heating mat,

please refer to the instructions included

in the "Merging Kit" available from

Miele.

Installation

. . . with partition

The minimum thickness of the partition

is 5/8" (16 mm).

If there is a partition between the

adjacent appliances, then each

appliance is to be individually installed

within its own niche.

A heating mat must only be installed if

the partition wall is less than 6"

(160 mm) wide:

For instructions on how to install the

heating mat please refer to the

instructions included in the "Merging

Kit".

The "Merging Kit" can be obtained

from Miele.

Side panels

If one side of the appliance is visible, a

side panel must be used.

The side panel must be firmly secured

to the wall, the floor and the overhead

furniture/fixtures before the appliance is

placed in the cavity.

The dimensions of the side panel are

taken from the opposite wall of the

installation space. During installation,

ensure that the cavity is square and the

measurements are correct.

Installation

Door dimensions (open min. 90°)

KWT 16x1 SF 26 5/8" (677 mm)

KWT 16x1 SF 12" (305 mm)

1. Power supply

Dimensions

Niche dimensions

KWT 16x1 SF 24 1/2" (622.2 mm) 24" (610 mm)

Dimensions

Before you begin

Read these instructions completely

and carefully.

Have the appliance installed by a

qualified technician, according to

the enclosed installation instructions.

To reduce the risk of injury or

damage to the product, two people

should be used for installation.

These installation instructions are

intended for use by qualified installers.

In addition to these instructions, the

appliance must be installed in

accordance with all local codes. In the

absence of a local code, the following

should be used:

– In the USA, the National Electric

Code, ANSI/NFPA 70 - latest

edition/State and Municipal codes

and/or local codes.

–In Canada, the Canadian Electric

code C22.1 - latest edition/Provincial

and Municipal codes and/or local

codes.

Tools needed for installation

–Cutter with adjustable blade

–Cordless screwdriver T 20

–Torx screwdriver T 20

–Hammer drill for drilling holes in wall

or floor

–Wood drills in different sizes

–Hammer

–Open end wrench ½" (SW 13 mm)

–Box-end wrench

– 5/16" (8 mm) hex nut driver

– Adhesive tape

– Multi-grip pliers

– Level

– Metal tape measure

– Square

Other

–Stepladder

–Dolly, hand tuck

–Wooden beam (cross section min.

3" x 4" [75 cm x 100 cm)] as an

alternative tilt protection, length

according to the width of the

installation cavity)

–Wood screws in different sizes

Optional Tool

–"Merging Kit" for side-by-side

installation.

Installation

Otros manuales para KWT 1601 SF

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Enfriador de vino de Miele

Miele

Miele KWT 6312 UGS Manual de usuario

Miele

Miele KWT4154UG1 Manual de usuario

Miele

Miele KWT 6833 SG Manual de usuario

Miele

Miele KWT 6321 UG Manual de usuario

Miele

Miele KWT 6322 UG Manual de usuario

Miele

Miele KWL 4912 SG ed Instrucciones de montaje

Miele

Miele KWT 4154 UG-1 Hoja de especificaciones

Miele

Miele KWL 1630 S Hoja de especificaciones

Miele

Miele KWT 4154 UG-1 Hoja de especificaciones

Miele

Miele KWT 2662 ViS Manual de usuario

Miele

Miele KWT 6321 UG Manual de usuario

Miele

Miele KWT 1601 SF Hoja de especificaciones

Miele

Miele KWT 1601 Vi Manual de usuario

Miele

Miele KWT 1601 Vi Manual de usuario

Miele

Miele KWT 4154 UG Manual de usuario

Miele

Miele KWT 6321 UG Manual de usuario

Miele

Miele KWNS 28462 E ed/cs Manual de usuario

Miele

Miele KWT 1601 Vi Manual de lista de piezas

Miele

Miele KWL 4612 S Manual de usuario

Miele

Miele KWT 6834 SGS Manual de usuario

Miele

Miele KWT 6312 Manual de usuario

Miele

Miele KWT 1601 SF Manual de usuario

Miele

Miele 09 507 300 Manual de usuario

Miele

Miele KWT4154UG1 Hoja de especificaciones

Manuales populares de Enfriador de vino de otras marcas

U-Line

U-Line Echelon Wine Captain 2075WC Manual del propietario

Haier

Haier WS50GA Manual de usuario

Cavist

Cavist 62 Manual de usuario

Kenmore

Kenmore 461.99130 Manual de usuario

Danby

Danby DWC113BLSDB Manual de usuario

Caple

Caple Wi6128 Manual de usuario

Avanti

Avanti WC1001 Manual de usuario

Frigidaire

Frigidaire FFWC38F6LS Manual de usuario

Titan

Titan TT-W2454SZ Manual de instalación

Klarstein

Klarstein Botella 166 Uno Manual de usuario

Costway

Costway FP10130WL Manual de usuario

Lemair

Lemair LWC59 Manual de usuario

Haier

Haier JC-125GEA Manual de usuario

Caple

Caple WCi46B Manual de usuario

Climadiff

Climadiff CLI24 Guía rápida

Viking

Viking VCWB301LSS Manual de usuario

Caple

Caple WC6511 Manual de usuario

Vinvautz

Vinvautz VZ08BHK Manual de usuario