Midea NF15-16D Manual de usuario
OWNER’S MANUAL
FAN HEATER
MODEL: NF15-16D
READ AND SAVE THESE INSTRUCTIONS
Version 1.0 2016
Attention: Pictures in the IM are for reference only.
1
IMPORTANT INSTRUCTIONS
PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances,basic precautions should always be followed to
reduce the risk of fire,electric shock,and injury to persons,including the following:
1. Read all instructions before using heater.
2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot
surface. If provided, always use handles when moving this heater. Keep
combustible materials such as furniture, pillows, bedding, papers, clothes and
curtains at least 3 feet (0.9m) from the front of the heater and keep them away
from the sides and rear.
3. Extreme caution is necessary when any heater is used by or near children or
invalids and whenever the heater is left operating and unattended.
4. Always unplug the heater when not in use.
5. Do not operate any heater with a damaged cord or plug or after the heater
malfunctions, has been dropped or damaged in any manner. Discard heater or
return heater to authorized service facility for examination, electrical or
mechanical adjustment, or repair.
6. Do not use the heater outdoors.
7. This heater is not intended for use in bathroom, laundry areas and similar moist
indoor locations. Never locate heater where it may fall into a bathtub or other
water container.
8. Do not run cord under carpeting. Do not cover cord with throw rugs, runners,
or similar coverings. Do not route cord under furniture or appliances. Arrange
cord away from traffic area and where it will not be tripped over.
9. CAUTION: This appliance has a polarized plug (one blade is wider than the
other). To reduce the risk of shock, this plug is intended to fit only one way in a
polarized outlet. If the plug does not fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician. DO NOT attempt to defeat this
safety feature. To do so could result in an electric shock hazard.
10. This heater draws 12.5 amps during operation. To prevent overloading a
circuit, do not plug the heater into a circuit that already has other appliances
working.
11. CAUTION: It is normal for the plug to feel warm to the touch; however, a loose
fit between the AC outlet (receptacle) and plug may cause overheating and
distortion of the plug. Contact a qualified electrician to replace loose or worn
outlet.
2
12. To disconnect the heater, first turn controls to off, then remove plug from
outlet. Never pull by the cord.
13. Do not insert or allow foreign objects to enter any ventilation or exhaust
opening as this may cause an electric shock or fire, or damage the heater.
14. To prevent a possible fire, do not block air intakes or exhaust in any manner.
Do not use on soft surface, like a bed, where openings may become blocked.
15. A heater has hot and arcing or sparking parts inside. Do not use it in the areas
where gasoline, paint, or flammable liquids are used or stored.
16. Use this heater only as described in this manual. Any other use not
recommended by the manufacturer may cause fire, electric shock, or injury to
persons.
17. CAUTION: Always plug heaters directly into a wall outlet/receptacle. Never
use with an extension cord or reloadable power tap (outlet/power strip).
18. The output of this heater may vary and its temperature may become intense
enough to burn exposed skin. Use of this heater is not recommended for
persons with reduced sensitivity to heat or an inability to react to avoid burns.
19. Disposal of oil contained within should be in accordance with applicable
regional, national, and local laws and regulations.
20. “SAVE THESE INSTRUCTIONS”
3
OPERATING INSTRUCTIONS
● Check before turning on the machine
1. Check if the power wire is under good condition.
2. The product adopts 120V AC power supply, before use, please confirm if the rated current of
the power socket meets the local requirements with safe grounding device, otherwise, please
replace it with the qualified socket.
● Put the machine on the flat place
Uneven place may possibly cause the turnover switch at abnormal position, then the heater
can’t work after turning on, therefore, please put the heater on the flat place, at least the surface
below the base of the heater must be flat.
● Temperature Control Knob
Insert the plug into the power socket, then turn the Temperature Control knob clockwise, when
hearing the “poop” sound (it means the temperature controller is on), adjust the Temperature
Control knob to the desired temperature level.
● Power Switch Knob
Turn the gear knob, so that you can switch among 4 functions of the fan, Low 600W(LOW),
Middle 900W(MED),High 1500W(HIGH).
● Turn off the Heater
A. Turn the Power Switch Knob to OFF position.
B. Turn the Temperature Control knob anticlockwise to the initial position.
C. Remove the power plug, store the heater after the entire machine has become cool.
● Safety Protection
1.Overheat protection: When the temperature in the heater is too high due to abnormality in the use
environment or improper use, the thermostat device can automatically cut off the power and the
heater stops working. After the whole heater is cooling, the heater can return to the normal use after
removing the abnormality.
2.Inversion protection: When the whole heater is inverted, the safety system will automatically cut off
the power, and return to the work state before inversion afterthe body is placed upright.
Temperature
control knob
Pilot light
Power selection knob
Safty grill
4
TROUBLESHOOTING
If the product does not operate or does not operate properly, first check according to the following
list. If the reason the product does not operate or does not operate properly is not included in the
following list, the product mayhave failed. At this time, it is recommended to send the product to
the dealer for treatment.
Problem Possible Cause Solution
After the power is
engaged, the power
indicator light does not
illuminate and the
machine does not work.
The plug may not be
plugged well.
Check whether the plug is
properly inserted intothe
receptacle.
The temperature control
knob is not turned in
place.
Check whether the
temperature control knob
is turned to the ON
position.
The machine suddenly
stops during heating.
The temperature exceeds
the threshold of the
thermal cut-o.
Coolthe machine before
use.
MAIN TECHNOLOGY SPECIFICATIONS
Power supply: AC120V ~ 60Hz
MODEL MEDLOFAN HI
POWER REGULATION RANGE (W)
NF15-16D 900600 1500
Warning:This heater cannot achieve accurate temperature control of the enviroment, and thus cannot be
used as insulation device for storage environment, items, animals and plants.
Tabla de contenidos
Otros manuales de Calentador de Midea
Midea
Midea NY2009-13A1L Manual de usuario
Midea
Midea NY2311-20MR Manual de usuario
Midea
Midea NDK20-21AE Manual de usuario
Midea
Midea NTH15-20AR Manual de usuario
Midea
Midea NDK15-12K Manual de usuario
Midea
Midea NF20-16BA Manual de usuario
Midea
Midea NYERF Manual de usuario
Midea
Midea HO-0279 Manual de usuario
Midea
Midea NY1507-17QR Manual de usuario
Midea
Midea NS8-15D1 Manual de usuario
Midea
Midea NT20-21A Manual de usuario
Midea
Midea NY2513-20M Manual de usuario
Midea
Midea NY2009-20M Manual de usuario
Midea
Midea NTH15-20AR Manual de usuario
Midea
Midea NT15-20A Manual de usuario
Midea
Midea NTH15-22GR Manual de usuario
Midea
Midea NT20-22E Manual de usuario
Midea
Midea NY1506-18SRA Manual de usuario
Midea
Midea NTH20-18MRA Manual de usuario
Midea
Midea NT15-20A Manual de usuario
Manuales populares de Calentador de otras marcas
Empire Heating Systems
Empire Heating Systems WCC65 Manual de usuario
Wetekom
Wetekom 92 86 43 Manual de usuario
Desa
Desa SPC170-F Manual de usuario
Watlow
Watlow Watrod Electric Tubular Heaters Manual de usuario
Haverland
Haverland ECO-DRY GPS Series Manual de lista de piezas
Stelpro
Stelpro ASILVC2060 Series Manual de usuario