Microtek XT5750 HS Manual de usuario

Step 2: Install Software

Step 1: Unpack Contents

Start Here

Installing your Microtek XT5750 HS

Unpack your scanner package and check for

major components.

1. XT5750 HS Scanner

2. Power adapter

3. Hi-Speed USB cable

4. Software CDs/DVDs

5. Start Here guide

Important:You must install software before

connecting your scanner.

Always close any open programs and turn off Anti-

virus utilities before installing software.

I49-005389 A, March 2021

A. Turn on your computer.

B. Place the Microtek Software CD/DVD into a drive, and follow the on-screen

instructions to install the scanner driver and software.

C. Restart your computer at the end of all software installation.

NOTE: If the Microtek Software Installer screen does not come up automatically, double-click the

following in succession: “My Computer”; the CD/DVD-ROM icon; then cdsetup.exe to start the

installer program.

Connect Scanner

To the power adapter

A. Connect one end of the power adapter to the back of the scanner.

B. Plug the other end of the

power adapter into a wall outlet or

other power source.

To the Hi-Speed USB cable

C. Connect one end of the Hi-Speed USB cable to your computer.

D. Connect the other end of

the Hi-Speed USB cable to the

scanner’s USB port.

E. Press and hold the Power button ( ) until the

POWER indicator becomes blue.

Once the system detects the scanner, the

scanner is ready to scan.

Customize the Function Buttons

The XT5750 HS scanner is equipped with 4 physical function buttons that can be

customized to automate a number of predened operations, such as scanning to a le,

sending an image to your printer or e-mail account, scanning for OCR, etc. Customizing

is done through the Scanner Button Settings interface in the ScanWizard DI, refer to the

scanner’s User’s Manual for more details.

4 programmable

function buttons

Positioning Documents

1. Raise the scanner lid.

2. Pplace the document to be scanned face down on the glass surface of the scanner.

3. Lower the scanner lid.

Position a book or a bound document:

Align the spine or inner edge of the book with the

arrow icon ( ) located at the lower right corner of the

scan bed and along the dotted line shown as picture.

If necessary, lift the scanner lid straight up or remove

it from the hinges when scanning a thick book.

Position a single-sheet document:

Align the top corner of the document with the arrow

mark ( ) located at the upper-right corner of the scan

bed, with its edges rmly against the rulers.

Scanning Documents

1. Place the document to be scanned facing down on the scanner’s glass surface.

2. Launch ScanWizard DI as a stand-alone program by clicking on the ScanWizard DI icon

on the desktop.

3. Click the Scan Setup button in the interface to activate the Scan Setup interface.

4. In the Scan Setup interface, follow the steps below to specify your basic settings.

a) Select Flatbed in the Scan Source as your image

input device.

b) Select the appropriate image type in the Color

Mode as your image output type.

c) Select a dimension in the Paper Size as your

preview image size.

d) Select a desired resolution in the Resolution for

your image output resolution.

e) If necessary, select “Text Orientation Recognition”

in the Rotate to ensure the scanned images in

a readable orientation. When it is selected, you

can select the preferred language used as an

identication in the options menu.

f) If “Auto-crop” & “Auto-deskew” are selected,

the scanner automatically detects the size of the

original image, crops the full scan frame to t the

image, and removes unwanted black borders after

the scan, as well as corrects the distorted image

for proper alignment.

5. Click the Show Preview Window and Show Setting Window tabs in the Scan Setup

interface to display other interfaces which are helpful for your scanning processing.

6. Click the Preview button to perform a preliminary view of the entire image. When

done, a preview image appears in the Preview window.

7. Go to the “General” panel by clicking the General tab in the Settings window. Specify

the settings for your requirements there.

a) Select the image type in the Document Type as your input image type.

– Select Photo to scan color prints.

– Select Text to scan text.

b) If necessary, check “Remove Blank Page” and

“Remove Punch Hole” to enhance the quality of the scanned images.

8. If necessary, go to the “Image Process” panel by clicking the Image Process tab in the

Settings window.

Use the image correction tools presented there to enhance the image quality according

to your specic requirements.

9. Click the OK button to close the Scan Setup interface and return to the Main interface

of ScanWizard DI.

10. In the Main interface, click the File Format menu button to select a le format for the

scanned images.

11. In the Main interface, click the File Name menu button to specify a le naming method

for the scanned images.

12. In the Main interface, click the Normal Scan button to start scanning.

When done, the scanned images will be automatically saved into the folder dened in

the File Location menu box. At the same time, the scanned images will be displayed

in thumbnail sizes in the Thumbnail View window and labeled with the le name and

le format specied earlier.

13. Click the Open Folder button to locate the scanned images if you want to view.

NOTE: For more details on other scanning scenarios applicable to your scanner, refer to the scanner’s

User’s Manual in the Microtek Software CD/DVD.

AP control panel (Main interface)

File Location

menu box

Click on a

thumbnail image

to enlarge it in

the Image View

Window at the

right side of the

interface.

TWAIN driver control panel (Scan Setup interface)

Problems?

The LED indicators on the button panel of the scanner indicate different states of the

scanner. The POWER indicator stands for power and should always stay on steady when

the scanner is on.

First, make sure that you have followed Steps 1 to 3 as described in this guide (unpack,

install, connect). Then if your problem is listed here, try the suggested solution.

1. No light comes on when the scanner is turned on.

Make sure your scanner is connected to your computer and plugged into a power

source.

Press and hold the Power button until the POWER indicator becomes blue.

2. The Add/Remove Hardware Wizard appears on your screen.

Click the “Cancel” button and close the ScanWizard DI software.

Disconnect the USB cable from your computer, and refer to the installation instructions

in this guide or the scanner's User’s Manual.

3. When trying to scan, an error message appears on your screen that reads, “Can’t Find

Scanners”.

Make sure your scanner is connected to your computer and plugged in to a power

source.

Uninstall and reinstall the ScanWizard DI software.

4. When trying to scan, an error message “Code: -1000, No response from

scanner”appears on your screen.

Make sure that the POWER indicator has become blue. If not, press and hold the

Power button until the POWER indicator becomes blue.

5. After clicking scan, a blank screen appears.

Uninstall and reinstall the ScanWizard DI software.

SCAN indicator

(Green)

POWER indicator

(Blue)

Blue On - Ready to scan

Green Flashing - Scanning

Red On - Error

All Off - Scanner is off

DoYou Need Assistance?

Manuals

If you have additional questions and need further instruction or information, we provide

electronic manuals for:

1. Using your XT5750 HS Scanner (User’s Manual)

2. Using the ScanWizard DI scanning software (Reference Manual)

To access the electronic manuals: Insert the scanner’s software CD/DVD into your

computer’s CD/DVD-ROM drive. Next, locate and click the “Manuals” option when the

software installer window appears on your screen. Finally, select and click the title of the

manual you wish to view.

Missing Items

If your package is missing items, please call the Microtek Customer Service Department.

Drivers & Software Upgrades

After you nish the installation of software, if you found that the installed drivers and

software cannot run your product or your computer system properly later, please go to the

Microtek Download Service site at microtek.com/en/download to download and install any

updates you may require.

For additional information about Microtek products, please visit our website at www.

microtek.com.

ColoRescue are trademarks or registered trademarks of Microtek International,

Inc. All other trademarks or registered trademarks are the property of their

respective holders. Specications, software and hardware bundles are subject to

change without notice. Delivery of technical support services subject to change

without notice. Not responsible for typographical errors.

Power Adapter

Use only power supplies (AC/DC adapters) listed below:

Voltage Manufacturer Model No.

AC100V to 240V KUANTEN KT241120200EU

AC100V to 240V KUANTEN KT241120200US

NOTE: Please make sure that the electrical outlet to where the scanner will be

connected is nearby and readily accessible.

Otros manuales para XT5750 HS

Tabla de contenidos

Otros manuales de Escáner de Microtek

Microtek

Microtek ScanMaker 4600 Manual de usuario

Microtek

Microtek ScanMaker 4800 Manual de usuario

Microtek

Microtek XT5750 HS Manual de usuario

Microtek

Microtek ArtixScan 120tf Manual de usuario

Microtek

Microtek ArtixScanDI 4020 Plus Manual de instrucciones

Microtek

Microtek ArtixScan DI 2020 Manual de usuario

Microtek

Microtek ScanMaker i460 Manual del propietario

Microtek

Microtek ArtixScan 120tf Manual de usuario

Microtek

Microtek ScanMaker 1000XL Plus Manual de instrucciones

Microtek

Microtek ArtixScan F2 Manual de instrucciones

Microtek

Microtek ScanMaker 9700XL Manual de usuario

Microtek

Microtek ScanMaker 3700 Manual

Microtek

Microtek ScanMaker 9800XL Plus Manual de usuario

Microtek

Microtek ScanMaker 1000XL Manual de instrucciones

Microtek

Microtek Bio-5050 Manual de usuario

Microtek

Microtek ArtixScan DI 6260S Manual de instrucciones

Microtek

Microtek ArtixScan M2 Instrucciones de montaje

Microtek

Microtek ScanMaker 3700 Manual de usuario

Microtek

Microtek ArtixScan1200DF Manual de usuario

Microtek

Microtek ScanMaker i800 Manual de usuario

Microtek

Microtek ScanMaker 8700 Pro Manual de usuario

Microtek

Microtek ArtixScan 1200DF Manual de instrucciones

Microtek

Microtek ScanMaker i800 Manual de usuario

Microtek

Microtek ScanMaker X12USL Manual de usuario

Manuales populares de Escáner de otras marcas

Plustek

Plustek Scanner Manual de usuario

Z/I Imaging

Z/I Imaging PhotoScan 2001 Manual de usuario

Renkforce

Renkforce DS100-5M Manual de usuario

Image Access

Image Access WideTEK A2 Manual de usuario

Canon

Canon imageFORMULA CR-120N Manual de usuario

Fujitsu

Fujitsu FI-4860C2 Manual de usuario

GeoSlam

GeoSlam ZEB Horizon Instrucciones de instalación

Kodak

Kodak i5800 Scanner Manual de usuario

Kodak

Kodak i7300 Manual de usuario

Revopoint

Revopoint POP Manual de usuario

Fujitsu

Fujitsu fi-4860C Manual de usuario

Eddyfi Technologies

Eddyfi Technologies Floormap X Manual de usuario

Faselase

Faselase F6 Manual de usuario

Fujitsu

Fujitsu CardMinder Manual de usuario

Uniden

Uniden BC340CRS Manual de usuario

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Manual de usuario

Mustek

Mustek PageExpress 4800 Pro Manual de usuario

Optex

Optex 750830 Manual de usuario