Microtek ObjectScan 1600 Manual de usuario
www.microtek.com
ObjectScan 1600
Object Scanner
User's Manual
2 ObjectScan 1600 User's Manual
Preface
Copyright
© 2017, Microtek International, Inc., all rights reserved. This document may not
be reproduced or copied in any way, stored electronically, or translated into any
language, without the permission of Microtek International, Inc.
Trademarks
Microtek, ScanMaker, ArtixScan, ScanWizard and ColoRescue are trademarks
or registered trademarks of Microtek International, Inc. All other trademarks or
registered trademarks are the property of their respective holders. Specications,
software and hardware bundles are subject to change without notice. Not
responsible for typographical errors.
Disclaimer
The contents of this manual have been checked carefully for accuracy, and every
effort has been made to ensure that there are no errors. However, Microtek
makes no guarantee as to the accuracy of the contents of this document and
reserves the right to make changes to the contents without prior warning.
I49-005160 C
November 2017
Microtek International, Inc.
No. 6, Industry East Road 3, Science Based Industrial Park, Hsinchu, 30075, Taiwan
Tel: 886-3-5772155, Fax: 886-3-5772598, http://www.microtek.com
ObjectScan 1600 User's Manual 3
FCC Compliance Statement
This equipment (Model: MRS-1600A3OS) has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
NOTE: A shielded Hi-Speed USB interface cable with ferrite core installed on the
scanner connector end must be used with this equipment.
Caution: Changes or modications not expressly approved by the manufacturer
responsible for compliance could void the user's authority to operate the
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
4 ObjectScan 1600 User's Manual
Safety Precautions
Before using your scanner, read the following safety guides carefully, which
detail the proper operation of the scanner and its accessories to prevent injuries
or damage to users or equipment.
Meanings of Symbol Signs
This indicates hazardous situation which, if not paid
attention, could result injury or damage to users or
equipment.
This indicates hazardous situation which, if not paid
attention, could result serious injury or death to users.
Power Supply:
• Use a power source only with a power rating specied on the marking label.
• Ensure to turn off the power of each device before connecting or
disconnecting the cables.
• Insert the plug completely into the outlet, as a loose connection may cause
arcing and result in re.
• Ensure to hold the plug or connector to disconnect the cable; otherwise,
if you pull the cable only, it may damage the core wire and result in re or
electric shock.
• Place and route the power supply cord such that it is not likely to be walked
on or pinched by items placed upon or against them, paying particular
attention to the cord near the power plugs, convenience receptacles, and at
the point where it exits from the outlet.
• When the scanner is left unattended and unused for long periods of time,
unplug it from the wall outlet.
Moving and Storing the Scanner:
• Always ensure that the scanner is stored properly before shipping or moving
it. Quick stops, excessive force, and uneven surfaces may cause the
product to overturn when moving.
• Do not hit or drop the scanner. The scanner may be damaged if it receives
a strong jolt, which may result in re or electric shock if the scanner is used
without being repaired.
• Do not place the scanner on any slippery, slanted, or unstable surface. The
product may slide or fall, causing serious injury to people as well as serious
damage to the product.
CAUTION
WARNING
ObjectScan 1600 User's Manual 5
• Do not use the scanner near water. Never spill liquid of any kinds on the
product, or it may result in electric shock or other hazards.
• This scanner should be situated away from heat sources such as radiators,
heat registers, stoves, or other products (including ampliers) that produce
heat.
• Do not store the scanner in which it may be exposed to direct sunlight.
• Do not place the scanner near the edge of a table. When the drawer of the
scanner is opened, the weight of the product may cause the scanner falling,
causing serious injury to people as well as serious damage to the product.
Using the Scanner:
• The maximum loading weight for upper and lower scan beds is 5.5 lbs (2.5
kg). Do not put any material on scan beds heavier than the loading limit.
Maintenance and Service:
• When the scanner is going to be cleaned, ensure to turn off the power of
each device and unplug the power cable from the AC outlet.
• When you need a repair service, unplug the scanner from the power outlet
and consult qualied service personnel.
• When replacement parts are required, use replacement parts that are
specied by the manufacturer or have the same characteristics as the
original parts.
6 ObjectScan 1600 User's Manual
Table of Contents
Preface ................................................................................................2
FCC Compliance Statement ................................................................3
Safety Precautions ..............................................................................4
Knowing about Your Scanner..............................................................7
Features of the Your Scanner ............................................................. 7
System Requirements ........................................................................ 8
Taking a Closer Look ......................................................................... 9
Front View ................................................................................. 9
Back View................................................................................ 10
Initiate Setup..................................................................................... 11
Step 1: Unpacking Package Contents ................................................ 11
Step 2: Installing the Software.......................................................... 12
Step 3: Unlocking the Scanner.......................................................... 13
Step 4: Installing the Upper Scan Bed................................................ 15
Step 5: Connecting the Scanner........................................................ 16
To the Power Source................................................................. 16
To the Hi-Speed USB Cable ........................................................ 16
Scanning the Materials......................................................................17
Positioning the Materials .................................................................. 17
Using ScanWizard Graph Software .................................................... 19
Maintenance ......................................................................................22
Appendix ...........................................................................................23
Optional Magnet Helpers.................................................................. 23
Troubleshooting .............................................................................. 25
Specications ................................................................................. 26
ObjectScan 1600 User's Manual 7
Knowing about Your Scanner
The ObjectScan 1600 is a professional scanner exclusively designed for
transferring originals of samples into digital formats. It is ideal for capturing
images for small and stereoscopic objects and these images can be used in many
categories, such as collections, teaching, researching, manufacturing and web
business. At the same time, the ObjectScan 1600 is also able to scan paper
materials, for example, prints and researching papers.
Features of the ObjectScan 1600
The ObjectScan 1600 comes with several important features, including the
following:
• Non-contact scan (on-top scan) Design — The ObjectScan 1600 takes on a
design of a non-contact scan (on-top scan) structure. Under this structure,
users have no needs to spin sample face down on the scan bed, and enjoy
the scan work without worrying about the problems that traditional atbed
scanners deal with, such as damage problem caused by directly contact
each other. The ObjectScan 1600 is perfect for digitalizing the originals of
samples.
• Energy-saving tri-wave LED light source — Adopting tri-wave LEDs as the
light source, when the scanner is detected by the system, there are no
requirements for any warm-up time before carrying out the scan, which
boots your productivity and reduces energy costs amazingly. With its stable
performance, the image quality will remain consistent even after used for a
certain period of time.
• Color CCD with 1600-dpi high resolution — The ObjectScan 1600 has a
color linear CCD with resolution that reaches up to 1,600 pixels per inch.
Thus, it can clearly capture images for shapes and textures of objects,
presenting original appearances of objects precisely and decreasing the
happenings of damages on objects when doing researches.
• Microtek ScanWizard Graph software — ScanWizard Graph is software
exclusively designed for scanning large-format graphs and objects. It is
provided with series of advanced functions and tools, providing instant and
complete helps to users who can therefore control the scanner easily and get
the best image results.
8 ObjectScan 1600 User's Manual
System Requirements
• DVD-ROM drive (for installing software)
• Color display with 24-bit color output capability
• 8 GB RAM or more recommended
• Intel Core i5 at 3.0 GHz PC or higher with USB 2.0 port
• Microsoft Windows 7 (64-bit), 8 (64-bit) or 10 (64-bit)
ObjectScan 1600 User's Manual 9
Taking a Closer Look
Front View
No. Names of Parts Functions of Parts
1 Indicators Displays the status of the scanner.
(Green and Orange)
2 Drawer of the Scanner Carries the upper scan bed and the lower scan bed of the scanner.
3 Handle of the Drawer Holds to open or close the drawer of the scanner.
4 Right Handle Holds to move the scanner.
10 ObjectScan 1600 User's Manual
Back View
No. Names of Parts Functions of Parts
1 Power Connector Connects the scanner to the power cord.
2 Power Button Turns the scanner on or off.
3 Hi-Speed USB Port Connects the Hi-Speed USB (USB 2.0) cable to the computer.
4 Left Handle Holds to move the scanner.
Otros manuales para ObjectScan 1600
2
Tabla de contenidos
Otros manuales de Escáner de Microtek
Microtek
Microtek ScanMaker 8700 Pro Manual de usuario
Microtek
Microtek TMA 1600 Manual de usuario
Microtek
Microtek ScanMaker 1000XL Plus Manual de usuario
Microtek
Microtek ScanMaker i280 Manual del propietario
Microtek
Microtek LightLid 35 Manual de usuario
Microtek
Microtek ArtixScan 6000XY Manual de usuario
Microtek
Microtek ObjectScan 1600 Manual de usuario
Microtek
Microtek ScanMaker 3750i Manual de usuario
Microtek
Microtek ArtixScan 4500t Manual de usuario
Microtek
Microtek ArtixScanDI 3130c Manual de usuario
Microtek
Microtek ScanMaker 4 Manual de instrucciones
Microtek
Microtek ScanMaker i900 Manual de usuario
Microtek
Microtek SCAN-IN-DEX 1000 Manual de usuario
Microtek
Microtek ArtixScan DI 2125c Manual de usuario
Microtek
Microtek ArtixScanDI 5230 Manual de usuario
Microtek
Microtek ScanMaker i4800 Manual de usuario
Microtek
Microtek ScanMaker 6000 Manual de usuario
Microtek
Microtek Artix Scan1100 Manual de instalación
Microtek
Microtek ScanMaker 4700 Manual de usuario
Microtek
Microtek ArtixScan 1800f Manual
