MicroBT Whats Miner M3 Manual técnico

Whats Miner All-in-one machine

operation instruction

(Lite version)

V1.2(H3 platform)

Shenzhen MicroBT Electronics Technology Co., Ltd.

1. Introduction of M3 Integrated Machine.......................................................................................3

2.Mine wiring, safety warning for operation on the shelf................................................................3

2.1.Matters needing attention in connection of Mine Machine.............................................. 3

2.1.1.Points for attention in connection of Control Panel 12V Power Line......................4

2.1.2.Matters needing attention in connection of Power supply Control Line................ 4

2.1.3.Matters needing attention in connection of Fan Line............................................. 5

2.1.4.Matters needing attention in data wiring connection of Force Plate..................... 6

2.1.5.Matters needing attention in connection of 12V Power Line with Power Plate.....6

2.1.6.Machine wiring inspection.......................................................................................7

2.2.Mining machine handling, on the shelf operation points for attention.............................7

3. Mine machine configuration environment preparation...............................................................8

3.1.Mine machine configuration equipment list...................................................................... 8

3.2.Mining machine network environment.............................................................................. 8

4.Mine machine connection and check before power on................................................................ 9

5.Mine data configuration (configured on the web page)............................................................. 10

5.1.Query dynamic ip address obtained by mining machine................................................. 10

5.1.1.Running WhatsMinerTools Software.....................................................................10

5.1.2.Query the ip address reported by the mine machine........................................... 10

5.2.Mine Pool & Miner data and configuration NTP Server address..................................... 12

5.2.1.Mine Pool & miner disposition.............................................................................. 12

5.2.2.Modify the address of the ntp synchronization server (optional).........................14

5.3. Configure mine machine static IP address (optional)...................................................... 15

5.4. English and Chinese language switching of Mining Machine Page................................. 17

6.Mine machine running condition check...................................................................................... 17

7.Batch data configuration, status check, firmware upgrade........................................................ 19

8.Disassembly and installation of integrated machine.................................................19

8.1. Disassembly and installation of Power supply.................................................................19

8.1.1.Power disassembly machine..................................................................................19

8.1.2.Installation of power supply.................................................................................. 23

8.2.Disassembly and installation of Control Panel..................................................................24

8.2.1.Disassembly of control panel.................................................................................24

8.2.2.Installation of control panel...................................................................................25

8.3.Disassembly and installation of Force Plate..................................................................... 26

8.3.1.Disassembly of force plate.....................................................................................26

8.3.2.Installation of force plate.......................................................................................29

1. Introduction of M3 Integrated Machine

Whatsminer M3 integrated machine

Bitcoin miner

The product parameters are as follows:

Computational power: 12TH/S

Chip: 189 28nm ASIC

Power consumption: 0.18~0.19kw/TH

Supporting Power supply: Shenma Power supply P5 (220vU 2250W)

Control board: with ambient

temperature: -5 ℃~ 40 ℃whole

machine size: 375mm*130mm*225mm

2.Mine wiring, safety warning for operation on

the shelf

2.1.Matters needing attention in connection of Mine

Machine

Mine machine 12V power line, power supply control line, fan line must be

correctly connected, if due to the connection error, resulting in control board,

force board burning, the whole machine and veneer will not belong to the scope

of warranty!

2.1.1.Points for attention in connection of Control Panel 12V Power Line

When connecting the power cord of the control board, the plug of the power cord

and the clasp at the two ends of the power outlet of the control board must

correspond to each other, and the plug of the power cord cannot be inserted into

the control board socket by force. If backplugged, power on could burn down the

control board and burn out the signal wiring

Correct connection of power cord plugs and sockets:

Wrong connection of power cord plugs and sockets:

2.1.2.Matters needing attention in connection of Power supply Control Line

The power supply control line is 3pin red, black and yellow wire, 3 small ports

face out, the slot is inserted relative bit:

2.1.3.Matters needing attention in connection of Fan Line

Fan line is 4pin blue, yellow and red black line, 4 small mouth outside, card

slot relative bit insert:

2.1.4.Matters needing attention in data wiring connection of Force Plate

2.1.5.Matters needing attention in connection of 12V Power Line with Power Plate

When connecting the power cord of the force board, the power cord connecting

post and terminal must correspond to each other (yellow power cord is connected

to the red cable, and the red pole is connected to the positive pole (V);). The

black power cord is connected to the black pole, and the black pole is

connected to the negative pole (V-), which is tightened with screws. If the

connection is reversed, the power supply may burn down the machine.

Correct connection method of power cord connecting post and

terminal:

2.1.6.Machine wiring inspection

After all mine connections are connected, check again to confirm that the connection is

correct.

2.2.Mining machine handling, on the shelf operation

points for attention

In the process of ore machine handling and loading, data wire

arrangement, power control line, fan wire are strictly prohibited as

lifting handle, lifting machine and power supply. By connecting the

teena machine and the power supply, the connection will be damaged, the

connection will be loosened, and the control board will be physically

damaged over the carrying capacity. The resulting hardware damage and

failure will not belong to the scope of warranty!

3. Mine machine configuration environment

preparation

3.1.Mine machine configuration equipment list

Serial

number

tool

name

quantita

tive use

remarks

Serial number

tool name

quantitative use

remarks

Serial

numbe

r tool

name

quantit

ative

use

remark

Serial number tool name

quantitative use remarks

Serial number tool

name quantitative use

remarks

comput

1 computer 1

mine machine

configuration

operation

compu

ter 1

mine

machin

configu

ration

operati

1 computer 1 mine

machine configuration

operation

Mine power

supply

Configuration of mine

power supply

network switch

Configuration of mine

machines and

configuration

Network switches

can connect to

external networks

DHCP/NTP

server / router

1, provides

dynamic IP

address 2 for

initial power

DHCP/

NTP

server

router

DHCP/NTP server / router

1, provides dynamic IP

address 2 for initial

power on the mine

machine, and ntp

network time machine

DHCP/NTP server /

router 1, provides

dynamic IP address 2

for initial power on

the mine machine,

3.2.Mining machine network environment

By default, DHCP acquires dynamic ip, by default, so DHCP servers must be configured in the

mine network, or the dhcp dynamic ip address service must be turned on by the router. The

running time of mine machine and the correctness of calculation force statistics depend on the

network ntp time. By default, the mine machine has multiple ntp server addresses of public

network. In order to speed up the speed of obtaining network time by ntp and improve the time

precision, It is recommended that a local ntp server be configured in the mine network.

4.Mine machine connection and check before

power on

(1) before connection and electrification, the miner shakes the mine machine in accordance with

the warning signs on the side of the mine machine to check whether any radiator or other device

is off, to ensure that there is no radiator or other period of abscission before connection and

power up. (2) the mine machine is connected to the power cord, the network port is connected to

the switch, the control line of the power supply is connected to the I2C socket of the control board,

and the signal wiring, the power control line and the fan control line are checked, so as to ensure

that the connection is correct, In order to power the

mine.

Note: (1) 12V power cord connection post and terminal, control board power cord

socket outlet corresponding to ensure the correct connection of the power source

positive and negative pole, otherwise the power line positive and negative pole

connection, it is possible to burn the power board, control board or power

supply, Hardware damage due to power cord connection is not covered by warranty.

(2) the power supply control line must be connected between the control board

and the power supply, otherwise, the problem of low calculation force may be

caused by the failure to control the output of the power supply voltage. (3) the

control panel must be reliably connected with the fan line. If the fan line

falls off or the connection is bad, it may cause the miner to be unable to cool

down, and the load plate can be operated at lower frequency. In 2003, the

calculation power decreased.

5.Mine data configuration (configured on the

web page)

5.1.Query dynamic ip address obtained by mining

machine

5.1.1.Running WhatsMinerTools Software

The data of mine machine is configured with PC connected to the same network

where the miner is located, running the WhatsMinerTools software on PC, selecting

the "probe ip" tab, setting the room number, rack number, layer number on the

rack, and position number of the layer in which the mine machine is located.

Click start。

5.1.2.Query the ip address reported by the mine machine

The main results are as follows: (1) after 30 s, the yellow light and green light

of the net are always on and the green light twinkles under normal conditions.

When the IPFOUND function button (prominent long button) is pressed on the panel

of the mine machine control board, the two LED indicator lights on the right

flicker several times, indicating that the mine machine has broadcast the IP and

MAC addresses of the mine machine to the network.

Tabla de contenidos

Otros manuales de Hardware de computadora de MicroBT

MicroBT

MicroBT WhatsMiner M10S Manual de usuario

MicroBT

MicroBT WhatsMiner M20S Manual de usuario

MicroBT

MicroBT WhatsMiner M3 Manual de usuario

MicroBT

MicroBT WhatsMiner M21S Manual de usuario

MicroBT

MicroBT M34S+ Manual de usuario

MicroBT

MicroBT WhatsMiner M31S Manual de usuario

MicroBT

MicroBT WhatsMiner M30S Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario