MGE UPS Systems Pulsar EX 700RT Manual de usuario

www.mgeups.com

Pulsar EX

EX 700RT / EX 1000RT

EX 1500RT

Installation and User

Manual

MGE UPS SYSTEMS,INC.

SAVE THESE INSTRUCTIONS. This manual contains important instructions that should be followed during

installation and maintenance of the UPS and batteries.

Thank you for selecting an MGE UPS SYSTEMS, INC. product to protect your electrical equipment.

The Pulsar EX RT range has been designed with the utmost care.

We recommend that you take the time to read this manual to take full advantage of your UPS’s many features.

MGE UPS SYSTEMS, INC. pays great attention to the environmental impact of its products.

Measures that have made Pulsar EX RT a reference in environmental protection include:

◗The eco-design approach used in product development,

◗Recycling of Pulsar EX RT at the end of its service life.

To discover the entire range of MGE UPS SYSTEMS, INC. products and the options available for the Pulsar EX RT

range, we invite you to visit our web site at www.mgeups.com or contact your MGE UPS SYSTEMS, INC. representative.

This manual contains important instructions for Pulsar EX RT Models that must be followed during installation, operation

and maintenance of the UPS and batteries.

The Pulsar EX RT models that are covered in this manual are listed below:

UPS EX 700RT (700VA/490W), part number 85070.

UPS EX 1000RT (1000VA/700W), part number 85100.

UPS EX 1500RT (1500VA/1050W), part number 85150.

For extended back up time, the above UPS’s can be used with the optional extended battery module, Pulsar EXB 1500RT

(36Vdc, 14Ah), part number 85001.

The UPS Pulsar EX 700RT, EX 1000RT, and EX 1500RT are intended for installation in an environment within 0 to 40°C,

free of conductive contaminant.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required

to correct the interference at his own expense.

Important safety instructions

Read before installing product

Introduction

Page 2 - 86-153850-00 A01

86-153850-00 A01 - Page 3

CAUTION: Safety of persons

◗

The UPS has its own internal power source (the battery). Consequently, the power outlets may be energized even if the UPS

is disconnected from the AC power source.

◗

Dangerous voltage levels are present within the UPS. It should be opened exclusively by qualified service personnel.

◗

The UPS must be properly grounded. Measurements are required to ensure that the total leakage current of the UPS and the

protected equipment does not exceed 3.5 mA by checking their characteristics (maximum leakage current of the UPS = 2 mA).

◗

The battery supplied with the UPS contains small amounts of toxic materials. To avoid accidents, the directives listed below

must be observed:

- Never burn the battery (risk of explosion).

- Do not attempt to open the battery (the electrolyte is dangerous for the eyes and skin).

- Comply with all applicable regulations for the disposal of the battery.

- Batteries constitute a danger (electrical shock, burns). The short-circuit current may be very high. Precautions must be

taken for all handling: remove watches, rings, bracelets and any other metal objects, use tools with insulated handles.

- Do not lay tools or metal parts on top of batteries.

CAUTION: Product Safety

◗

The UPS connection instructions and operation described in the manual must be followed in the indicated order.

◗

UPS must be connected to a nearby wall outlet that is easily accessible. The UPS can be disconnected from the AC power

source by removing the power cord.

◗

Check that the indications on the rating plate correspond to your AC powered system and to the actual electrical consumption

of all the equipment to be connected to the UPS.

◗

Never install the UPS near liquids or in an excessively damp environment.

◗

Never let a foreign body penetrate inside the UPS.

◗

Never block the ventilation grates of the UPS.

◗

Never expose the UPS to direct sunlight or source of heat.

◗

If the UPS must be stored prior to installation, storage must be in a dry place.

◗

The admissible storage temperature range is -25ºC to +55ºC.

Special Precautions

◗

All handling operations will require at least two people (unpacking, installation in rack system).

◗

Once installed and connected to the AC power source for the first time, the battery will start to charge. Full charging to obtain

the rated battery backup time requires at least 8 hours.

◗

Before and after the installation, if the UPS remains de-energized for a long period, the UPS must be energized for a period of

24 hours, at least once every 6 months (for a normal storage temperature less than 25°C). This charges the battery, thus

avoiding possible irreversible damage. During the replacement of the battery module, it is imperative to use the same type and

number of element as the original battery module provided with the UPS to maintain an identical level of performance and

safety. In case of doubt, don’t hesitate to contact our after sales department (for more information, refer to the web site

www.mgeups.com).

Introduction

Page 4 - 86-153850-00 A01

Using this document

How to use this document

Icon Usage

Information may be found primarily by consulting:

◗The contents,

◗The index.

In the illustrations on the following pages, the symbols below are used:

LED off.

LED on.

LED flashing.

Audio indication.

Action.

Visual indication.

Notes, tips and information, help.

CAUTION: Hazard to personnel or equipment, information that must always be followed.

WARNING: Eminent hazard to personnel or equipment, information must always be followed.

Important information, help.

86-153850-00 A01 - Page 5

1. Presentation

1.1 System configurations ................................................................................................................7

Rack setup ......................................................................................................................................7

Tower setup ....................................................................................................................................7

1.2 Rear panel ......................................................................................................................................8

Pulsar EX 700RT, EX 1000RT, EX 1500RT, EXB 1500RT ............................................................8

1.3 Control panel ................................................................................................................................9

2. Installation

2.1 Unpacking ....................................................................................................................................10

2.2 Installation in rack position ........................................................................................................11

2.3 Installation in tower position ....................................................................................................12

2.4 Connection to the RS232 or USB communication port (optional) ........................................13

2.5 Installation of the optional communication-card ....................................................................13

2.6 Connections ................................................................................................................................14

3. Operation

3.1 Start-up ........................................................................................................................................15

3.2 LED indicators ............................................................................................................................15

3.3 Operation on battery power (following failure of AC input power) ............................................16

Transfer to battery power ..............................................................................................................16

Threshold for the low-battery warning............................................................................................16

End of backup time ........................................................................................................................16

3.4 Personalization (optional) ............................................................................................................17

Function..........................................................................................................................................17

"ON / OFF conditions" tab..............................................................................................................17

"Battery" tab ..................................................................................................................................17

"Output" tab....................................................................................................................................18

"Bypass" tab ..................................................................................................................................18

3.5 UPS Shutdown ............................................................................................................................18

3.6 UPS Remote Power Off ..............................................................................................................19

Contents

Page 6 - 86-153850-00 A01

4. Maintenance

4.1 Troubleshooting ..........................................................................................................................20

4.2 Replacement of the battery module ..........................................................................................22

5. Environment ....................................................................................................................................24

6. Appendices

6.1 Technical characteristics ..........................................................................................................25

6.2 Glossary ......................................................................................................................................26

6.3 Index ............................................................................................................................................27

Contents

PU L SA R

www.mgeups.com

100%

80%

50%

20%

test%

BYPASS

86-153850-00 A01 - Page 7

Tower setup

Rack setup

1.1 System configurations

1. Presentation

www.mgeups.com

P U L S A R

3.4 inches

(2U)

18.75 inches

(EX 700RT/EX 1000RT/EX 1500RT)

17.25 inches (19" Rack mount)

100%

80%

50%

20%

test%

BYPASS

E X

Model Part Weight

Number (Ibs/kg)

Pulsar EX700RT 85070 42.0 lbs (19.0 kg)

Pulsar EX1000RT 85100 42.0 lbs (19.0 kg)

Pulsar EX1500RT 85150 46.0 Ibs (20.5 kg)

Page 8 - 86-153850-00 A01

Pulsar EXB 1500RT (optional)

Pulsar EX1500RT

1Slot for communication-card option.

RS232 communication port.

USB communication port.

Six NEMA 5-15/20R (EX 1500 RT), six

NEMA-5-15R (EX 700 RT, EX 1000 RT)

receptacles for connection to AC power

load.

Two programmable NEMA 5-15/20R

(EX 1500 RT), two programmable

NEMA-5-15R (EX 700 RT, EX 1000 RT)

receptacles.

Pushbutton to test phase/neutral

inversion of AC power source.

LED indicating Site Wiring Alarm

Enable, with flashing and intermittent

buzzer. Reset fault with rear panel

button.

Connector for remote power off (RPO).

Connector for automatic detection of an

additional battery module.

Connector for an additional battery

module.

NEMA 5-15P Input power plug for direct

connection to AC power source.

Circuit breaker for battery ON/OFF and

protection.

1.2 Rear panel

1. Presentation

10 10

NOTE: The EXB 1500RT extended battery module is designed

to work with all EX700RT, EX100RT, EX1500RT UPS units.

Pulsar EX700RT/EX1000RT

86-153850-00 A01 - Page 9

2625

2423222120191817

(*) : ◗flashing LED + buzzer: battery fault (battery must be replaced).

◗flashing LED + long buzzer (once per hour): theoretical end of battery life (replacement recommended).

UPS

overload

Electronics

fault

Battery

fault *

Site Wiring

Fault

load

100%

80%

50%

20%

Press simultaneously at

least 3 seconds to reset

the “End of battery life”

alarm. 24

Status change in

progress.

Supplied with power

Operation on battery power.

Status of programmable outlet 2:

Operation in ON-LINE mode (backup power available).

Operation on bypass (no backup power available).

Status of programmable outlet 1:

1. Presentation

battery

remaining

100%

80%

50%

20%

ON / OFF.

◗Lamp test or buzzer OFF.

◗Forced transfer to bypass and back

by pressing button 3 times in less

than 5 seconds.

Hold down to display

percent load:

Alarms

1.3 Control panel

100%

80%

50%

20%

test %

BYPASS

Page 10 - 86-153850-00 A01

RS232 communication cable.

USB communication cable.

Telescopic rails for mounting in 19" bay with mounting hardware.

CD-ROM with the Solution-Pac and UPS Driver software.

Product documentation.

Two tower supports for the upright position.

2.1 Unpacking

2. Installation

PU L S A R

www.mgeups.com

100%

80%

50%

20%

test%

BYPASS

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unión Postal Universal de MGE UPS Systems

MGE UPS Systems

MGE UPS Systems Galaxy PW 30 kVA Manual de usuario

MGE UPS Systems

MGE UPS Systems 5103304XXX Manual de usuario

MGE UPS Systems

MGE UPS Systems Nova 600 AVR Manual de usuario

MGE UPS Systems

MGE UPS Systems Pulsar TM 30 Manual de usuario

MGE UPS Systems

MGE UPS Systems Pulsar ellipse 300 Manual de usuario

MGE UPS Systems

MGE UPS Systems Pulsar EXtreme C UPS 1000 VA Manual de usuario

MGE UPS Systems

MGE UPS Systems Pulsar Evolution 800 Manual de usuario

MGE UPS Systems

MGE UPS Systems Comet EXtreme Series Manual de usuario

MGE UPS Systems

MGE UPS Systems Pulsar EX20Rack Manual de usuario

MGE UPS Systems

MGE UPS Systems Galaxy PW Manual de usuario

MGE UPS Systems

MGE UPS Systems PULSAR EVOLUTION 3000 XL Manual de instrucciones

MGE UPS Systems

MGE UPS Systems Pulsar EX10Rack Manual de usuario

MGE UPS Systems

MGE UPS Systems EPS 6000 Manual de usuario

MGE UPS Systems

MGE UPS Systems Pulsar ellipse 1200 Manual de usuario

MGE UPS Systems

MGE UPS Systems Galaxy 3000 Guía de configuración

MGE UPS Systems

MGE UPS Systems Pulsar EXtreme CLA 2000 VA Manual de usuario

MGE UPS Systems

MGE UPS Systems Pulsar EXtreme2000 Manual de usuario

MGE UPS Systems

MGE UPS Systems 5000 RT Manual de usuario

MGE UPS Systems

MGE UPS Systems Pulsar Evolution 1100 Manual de usuario

MGE UPS Systems

MGE UPS Systems Pulsar EX7 Manual de usuario

MGE UPS Systems

MGE UPS Systems PULSAR EVOLUTION 2200 Manual de usuario

MGE UPS Systems

MGE UPS Systems EXB 5 Manual de usuario

MGE UPS Systems

MGE UPS Systems EXL 1000 Manual de usuario

MGE UPS Systems

MGE UPS Systems Comet TM 5 - 30 kVA Manual de usuario

Manuales populares de Unión Postal Universal de otras marcas

Pylontech

Pylontech Victron & Pylontech US5000 Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manual de usuario

Mecer

Mecer ME-1000-WTU Manual de usuario

Mustek

Mustek PowerMust 530(B) Plus Manual de instalación y operación

Emerson

Emerson Liebert NXL series Manual de usuario

MAKELSAN

MAKELSAN BOXER SERIES Manual de usuario

Block

Block PC-0524-400-0 Manual de usuario

CyberPower

CyberPower CP585LCD Manual de usuario

Eaton

Eaton 3S Instrucciones de montaje

CyberPower

CyberPower Office Tower Series UPS 1000 Manual de usuario

CyberPower

CyberPower BM100 Manual de usuario

Best Power

Best Power 610 Manual de usuario

Best Power

Best Power Unity/I UT3K Manual de usuario

Mustek

Mustek PowerMust 400 Offline Manual de usuario

Xantrex

Xantrex Trace 512 UR-UPS Manual de usuario

Forza

Forza SL-1501UL Manual de usuario

LEGRAND

LEGRAND keor 310081 Manual de usuario

ABB

ABB Conceptpower DPA 500 Manual de usuario