MGE UPS Systems Galaxy PW Manual de usuario

E-51028233XU/BF - Page 1

Installation manual

www.mgeups.com MGE UPS SYSTEMS

Battery and

auxiliary cubicles

supplied empty

Galaxy P ™

20 - 200 kVA

Page 2 - E-51028233XU/BF

E-51028233XU/BF - Page 3

Table of contents

Introduction ..................................................................................................... 4

Battery cubicles supplied e pty .............................................................................. 4

Auxiliary cubicle supplied e pty .............................................................................. 4

Installation ................................................................................................................ 4

Battery cubicles ............................................................................................ 5

Mechanical characteristics ....................................................................................... 5

Views of cubicles ...................................................................................................... 6

Installation ................................................................................................................ 8

Connections ............................................................................................................. 9

Auxiliary cubicle............................................................................................ 10

Mechanical characteristics ...................................................................................... 10

Views of cubicles ...................................................................................................... 10

All Galaxy PW products are protected by patents. They i ple ent original MGE UPS SYSTEMS technology not available to

other anufacturers.

To take into account evolving standards and technology, equip ent ay be odified without notice. Indications concerning

technical characteristics and di ensions are not binding unless confir ed by MGE UPS SYSTEMS .

This docu ent ay be copied only with the written consent of MGE UPS SYSTEMS. Authorized copies ust be arked

"Galaxy PW battery and auxiliary cubicles supplied e pty - installation anual n°51028233XU".

Page 4 - E-51028233XU/BF

Cubicles are supplied e pty for:

◗ installation of batteries not supplied

by MGE UPS SYSTEMS or batteries

delivered separately for transportation

reasons;

Introduction

◗ installation, in an auxiliary cubicle

with the sa e appearance, height and

depth as Galaxy PW cubicles, of user

ancillary equip ent used in conjunction

with a Galaxy PW UPS.

Battery cubicles supplied empty (20 to 200 kVA UPS)

E pty battery cubicles are available in

715 and 1015 wide and 1400 or

1900 high versions.

The 1015 wide cubicles have

central uprights front and rear which,

once s all brackets are installed,

prevent the shelves bending under the

weight of the battery cells.

For ease of installation/fixing of shelves

and connection of battery cells, it is

reco ended to install the battery cells

before placing the battery cubicles in

their final positions (the side and rear

panels of the cubicle can be re oved

to i prove access).

Each battery cubicle is designed to

acco odate an optional Merlin Gerin

circuit breaker as required which is

supplied as a separate kit and is

secured to the botto grating using 2

screws. This kit co prises:

◗ the battery circuit breaker "QF1" and

its connections;

◗ the syste for securing the circuit

breaker to the grating at the botto of

the cubicle;

◗ the auxiliary ter inal block "XR1" and

associated support, which:

◗ receives the circuit breaker tripping

voltage (fro the Galaxy PW rectifier-

inverter cubicle),

◗ sends circuit breaker "QF1" position

infor ation (to the Galaxy PW rectifier-

inverter cubicle).

Auxiliary cubicle supplied empty

every 25 . This provides for easy

attach ent of cross- e bers for

supporting all types of equip ent.

The lower level of the cubicle has two

re ovable cross- e bers for

supporting heavy ite s (transfor ers

for exa ple).

The e pty auxiliary cubicle is available

in 715 wide and 1400 or 1900

high versions.

Installation

These cubicles are supplied with 3

shelves (1400 high cubicles) or 4

shelves (1900 high cubicles) to

support the battery cells. The cubicles

which are not supplied with a battery

circuit breaker have a supple entary

shelf at the botto of the cubicle.

These shelves are provisionally

secured at the botto of the cubicle for

transportation purposes.

The cubicle structure consists of etal

sections provided with square holes

every 25 . These holes are used to

secure the shelves in accordance with

the heights of the battery cells to be

installed. Two cross- e bers per shelf

are supplied and are designed to be

secured between the structure uprights

on the sides of the cubicle to support

the shelves.

This cubicle co prises the basic

structure co on to all Galaxy PW

cubicles.

The cubicle structure consists of etal

sections provided with square holes

Refer to Galaxy PW installation anual

n° 51028231XU for the handling and

installation of Galaxy PW cubicles.

In particular, see the following

sections:

◗ "positioning the cubicles";

◗ "floor loads";

◗ "cubicle layout on false floor or

nor al floor".

E-51028233XU/BF - Page 5

Battery cubicles

Mechanical characteristics

715 1400 ±10 825 1165 610 710 145 350

1900 ±10 825 1665 610 710 180 350

1015 1400 ±10 825 1165 910 710 185 375

1900 ±10 825 1665 910 710 230 375

battery

cubicle width

in mm

max. weight

of battery

cells per shelf

in kg

cubicle

weight

in kg

inside dimensions in mm

(see cubicle views)

MNI

outside

dimensions in mm

The battery cubicles are installed to the

left of the Galaxy PW UPS rectifier-

inverter cubicle. The cubicles are

si ply convection cooled with an air

inlet at the front and an air outlet:

◗ at the top for the 1900 high

cubicles (a ini u clearance of

400 at the top over the full width of

the cubicle ust be kept);

◗ at the rear for the 1400 high

cubicles (a ini u clearance of

250 at the top over the full width of

the cubicle ust be kept).

The following figures show the front

view (Fig. 1), cross-section AA (Fig. 2)

and cross-section BB (Fig. 3), for a

715 or 1015 wide cubicle.

These figures show the installation

positions of the shelves, battery circuit

breaker and optional auxiliary

connector "XR1", together with the

openings provided for feeding the

cables via the botto .

Page 6 - E-51028233XU/BF

Battery cubicles (cont.)

Views of cubicles

Exa ple of a cubicle containing a battery circuit breaker. Cubicles not containing a battery circuit breaker have an additional row

of cells at the botto .

front view

(715 or 1015 mm

wide cubicles)

optional circuit

breaker QF1

connection via the bottom

(see cross-section BB)

earthing connection

position shelves as

required

Fig. 1

XR1

E-51028233XU/BF - Page 7

cross-section AA

(715 or 1015 mm wide

cubicles)

Fig. 2

air outlet (1900 mm high cubicle)

shelf support

cross-member

shelf

air inlet

connector XR1

optional battery

circuit breaker QF1

air inlet

cable trench

(if applicable)

connection

via the bottom

(see cross-section BB)

air outlet (1400 mm

high cubicle)

rearfront

cables tied to

the grating

Battery cubicles (cont.)

Page 8 - E-51028233XU/BF

Installation

Installing the optional

battery circuit breaker

◗ the circuit breaker is secured directly

to the grating at the botto ;

◗ position the battery circuit breaker

support and secure by eans of 4

screws as shown in the Fig. 4;

◗ bolt the support of connector XR1 to

the front RH upright of the cubicle

structure (see Fig. 3).

cross-section BB

(715 or 1015 mm wide

cubicles)

rear

front

Fig. 3

Fig. 4

◗ for 1015 wide cubicles, re ove

the front central upright for shelves

installation;

◗ if the cubicle is to include the

separately supplied battery circuit

breaker, this circuit breaker should be

installed first at the botto of the

cubicle.

XR1

QF1

opening for feeding

cables via the

bottom

earthing connection

battery circuit breaker

(optional) support plate for

connector XR1

securing of battery

circuit breaker kit by

2 screws

opening for feeding

cables via the bottom

bottom grating

Battery cubicles (cont.)

◗ re ove the shelves stacked at the

botto of the cubicle for transportation

purposes;

◗ prepare the bag of ounting

hardware and the support cross-

e bers used to install the shelves;

E-51028233XU/BF - Page 9

Fig. 5

Installing the shelves

◗ install the cage nuts in the square

holes in the structure uprights at the

required height for each of the shelf

support cross- e bers (4 nuts per

cross- e ber);

◗ bolt the shelf support cross- e bers

at the required heights (in accordance

with the battery cell di ensions) to the

structure uprights (see Fig. 5);

◗ for 1015 wide cubicles, install the

s all brackets in the slots provided in

the rear central upright at the required

height;

◗ install and connect together the

battery cells on the shelves before

installing the shelves in the cubicle;

◗ install the shelves together with the

associated battery cells sliding the

along the cross- e bers;

◗ bolt i peratively the shelves at the

front and rear to the structure uprights

and the cross- e bers (re ove the

cubicle rear panel if necessary);

◗ for 1015 wide cubicles, reinstall

the front central upright after fitting it

with s all brackets (supporting the

shelves) in the slots provided for this

purpose.

Battery cubicles (cont.)

Connections

◗ refer to Galaxy PW installation

anual n° 51028231XU for the cross-

sections of cables to be used and the

location of the connecting points in the

Galaxy PW rectifier-inverter cubicle

(power and auxiliaries).

note: the connecting cables are not

supplied.

Auxiliary connecting

cables XR1

Ter inals 1 to 4 of this ter inal block

ust be connected to connector XR3 of

the "Media Contacts 11" board of the

Galaxy PW rectifier-inverter cubicle to

provide the functions for auto atic

opening of battery circuit breaker "QF1"

(in case of e ergency shutdown for

exa ple) and detection of the battery

circuit breaker position for the UPS.

Details of these connections are given

in Galaxy PW installation anual n°

51028231XU, section "connection of

Media Contacts 11 standard auxiliary

circuits".

◗ connect the cubicle interconnection

cables;

◗ reconnect all the cables, leads and

bars (re oved for transport) between

the battery cells, starting fro the

botto shelf and finishing with the top

shelf;

◗ the cables providing connections

between shelves should be routed in

the space provided between the

shelves and the side panels at either

end of the shelves;

◗ the cables providing connections

between cubicles are routed via the

botto :

◗ via an opening in a false floor or

cable trench,

◗ or via the cubicle rear or side base

plates re oved or drilled for this

purpose;

Page 10 - E-51028233XU/BF

Views of cubicles

front view

Fig. 6

connection via the top

(1900 mm high cubicle, see top view)

earthing connection

(connection via the top)

earthing connection

(connection via the bottom)

connection via the bottom

(see cross-section BB)

Mechanical characteristics

auxiliary cubicle

width in mm cubicle weight

in kg

outside dimensions

in mm

715 1400 ±10 825 1170 610 710 100

715 1900 ±10 825 1670 610 710 120

1015 1400 ±10 825 1170 910 710 110

1015 1900 ±10 825 1670 910 710 135

inside dimensions in mm

(see cubicle views)

MNI

Auxiliary cubicle

Otros manuales para Galaxy PW

Tabla de contenidos

Otros manuales de Unión Postal Universal de MGE UPS Systems

MGE UPS Systems

MGE UPS Systems Pulsar ES 5+ Manual de usuario

MGE UPS Systems

MGE UPS Systems Pulsar ellipse 300 Manual de usuario

MGE UPS Systems

MGE UPS Systems Pulsar EXB 1000 - 1500 RT Manual de usuario

MGE UPS Systems

MGE UPS Systems 2000 Manual de usuario

MGE UPS Systems

MGE UPS Systems 250A Manual de usuario

MGE UPS Systems

MGE UPS Systems Pulsar MX Frame 15000 RT Manual de usuario

MGE UPS Systems

MGE UPS Systems 11+ Manual de usuario

MGE UPS Systems

MGE UPS Systems PULSAR EVOLUTION 3000 XL Manual de instrucciones

MGE UPS Systems

MGE UPS Systems EPS 7000 Manual de usuario

MGE UPS Systems

MGE UPS Systems Esprit 3 Manual de usuario

MGE UPS Systems

MGE UPS Systems Evolution 2000 RT 2U Manual de usuario

MGE UPS Systems

MGE UPS Systems Pulsar EX20Rack Manual de usuario

MGE UPS Systems

MGE UPS Systems 2200 RT 2U Manual de usuario

MGE UPS Systems

MGE UPS Systems Upsilon STS 30A Manual de usuario

MGE UPS Systems

MGE UPS Systems Esprit Manual de usuario

MGE UPS Systems

MGE UPS Systems Pulsar Evolution 1100 Manual de usuario

MGE UPS Systems

MGE UPS Systems GALAXY PW 100 Manual de usuario

MGE UPS Systems

MGE UPS Systems Pulsar Evolution 1500 Manual de usuario

MGE UPS Systems

MGE UPS Systems Comet EX 11 RT 3:1 Manual de usuario

MGE UPS Systems

MGE UPS Systems Ellipse 600 Manual de usuario

MGE UPS Systems

MGE UPS Systems 12 kVA Manual de usuario

MGE UPS Systems

MGE UPS Systems EPS 6000 Manual de usuario

MGE UPS Systems

MGE UPS Systems Pulsar EX7 Manual de usuario

MGE UPS Systems

MGE UPS Systems Pulsar 700 Manual de usuario

Manuales populares de Unión Postal Universal de otras marcas

Pylontech

Pylontech Victron & Pylontech US5000 Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manual de usuario

Mecer

Mecer ME-1000-WTU Manual de usuario

Mustek

Mustek PowerMust 530(B) Plus Manual de instalación y operación

Emerson

Emerson Liebert NXL series Manual de usuario

MAKELSAN

MAKELSAN BOXER SERIES Manual de usuario

Block

Block PC-0524-400-0 Manual de usuario

CyberPower

CyberPower CP585LCD Manual de usuario

Eaton

Eaton 3S Instrucciones de montaje

CyberPower

CyberPower Office Tower Series UPS 1000 Manual de usuario

CyberPower

CyberPower BM100 Manual de usuario

Best Power

Best Power 610 Manual de usuario

Best Power

Best Power Unity/I UT3K Manual de usuario

Mustek

Mustek PowerMust 400 Offline Manual de usuario

Xantrex

Xantrex Trace 512 UR-UPS Manual de usuario

Forza

Forza SL-1501UL Manual de usuario

LEGRAND

LEGRAND keor 310081 Manual de usuario

ABB

ABB Conceptpower DPA 500 Manual de usuario