MFJ MFJ-818 Manual de usuario

MFJ-818 Mobile SWR/Wattmeter Instruction Manual

1

MFJ-818 Mobile SWR/Wattmeter

Introduction

The MFJ-818 Mobile SWR/Wattmeter measures forward and reflected power and SWR

simultaneously and is designed to operate on 1.8-30 MHz. The MFJ-818 has two power

scales, which are selected with the top panel push button switch. The high power scale

measures 0-300 Watts forward power and 0-60 Watts reflected power. The low power

scale measures 0-30 Watts forward power and 0-6 Watts reflected power. The MFJ-818

utilizes a large illuminated three-inch Cross-Needle meter to read the SWR from 1:1 to

∞. A slide switch turns the back light on or off. This compact SWR/Wattmeter is rugged

enough to take the abuse of brutal mobile and portable operation.

Figure 1: MFJ Mobile SWR/Wattmeter

Installation

1. Connect your transmitter to the connector labeled TRANSMITTER and your

antenna to the connector labeled ANTENNA. It is important that you use good

quality coax and properly installed connectors.

2. An internal lamp backlights the meter scale. The lamp circuit requires 12 VDC

supply such as the MFJ-1312B. Use a 2.1 mm coaxial plug with the center

conductor positive and the sleeve ground. A slide switch turns the internal lamp

on or off.

3. To measure the power output capability of a transmitter/amplifier you should

connect a quality 50-ohm dummy load to the ANTENNA connector of the MFJ-

818.

MFJ-818 Mobile SWR/Wattmeter Instruction Manual

2

Operation

1. The meter’s full-scale forward and reflected power range is controlled by the

POWER RANGE button. When the button is pushed in, the forward power

scale is on 300 Watts and the reflected power scale is on 60 Watts. When the

button is pushed out, the forward power scale is on 30 Watts and the reflected

power scale is on 6 Watts. If your transmitter/amplifier runs more than 30 Watts

of output power, push the button in for 300 Watts. If your transmitter runs less

than 30 Watts of output power, push the button out for 30 Watts.

2. Forward power is displayed on the left-hand FORWARD meter scale. This scale

is calibrated from 0 to 300 Watts and is read directly in the 300W (in)position.

Each picket (scale mark) represents 5 Watts below 10 Watts, 10 Watts between 10

and 100 Watts, and 25 Watts between 100 and 300 Watts. In the 30W (out)

position, the forward power scale must be divided by 10. Each picket represents

0.5 Watts below 1 watt, 1 watt from 1 to 10 Watts, and 2.5 Watts from 10 to 30

Watts.

3. Reflected power is displayed on the right-hand REFLECTED meter scale.

Reflected power is 60 Watts full scale when the 300W (in) power scale is

selected, and 6 Watts full scale when the 30W(out) power scale is selected.

4. The most accurate power readings occur in the upper half of the meter scales.

When trying to measure power with a less than perfect match, the reflected power

should be subtracted from the forward power reading in order to find the true

power.

5. The SWR is read directly from nine red SWR curves that range from 1:1 to ∞.

SWR is measured by observing the point where the forward and reflected power

needles cross. The SWR is indicated by the red curve closest to the needle

crossing point.

MFJ-818 Mobile SWR/Wattmeter Instruction Manual

3

Calibration

The MFJ-818 has been calibrated at the factory. If it should ever need to be recalibrated,

then follow this procedure:

Equipment Needed

1. Transmitter capable of supplying enough power to obtain ½ to full-scale reading

at 14 or 21 MHz.

2. 50-ohm dummy load that is capable of handling full transmitter output power and

has better than a 1.15:1 SWR.

3. Power meter of know accuracy. The calibration will only be as good as the

standard reference meter.

4. 50-ohm cables capable of handling the power. RG-58/u is recommended. DO

NOT USE RG-59 or RG-11.

Meter Calibration

1. Refer to Figure 2 for the Test Setup and refer to the Trim Pot Location in Figure

3 for trim pot location.

2. Connect the Test Setup equipment as shown in Figure 2. Use a 50-ohm dummy

load for the antenna. Set the Transmitter to the 14 MHz in the 20-meter band.

3. With the POWER RANGE button pushed in for the 300 Watt scale, transmit 100

Watts as indicated on the reference meter. Adjust the HI FWD trim pot to set the

forward power scale to 100 Watts.

4. With the POWER RANGE button pushed out for the 30 Watt scale, Transmit 10

Watts as indicated on the reference meter. Adjust the LO FWD trim pot to set the

forward power scale to 100 Watts.

5. To set the reflected power, interchange the TRANSMITTER and ANTENNA

coax cables so that the transmitter is connected to the ANTENNA connector and

the dummy load is connected to the TRANSMITTER connector.

6. With the POWER RANGE button pushed in for the 60 Watt reflected scale,

Transmit 20 Watts as indicated on the reference meter. Adjust the HI REF trim

pot to set the reflected power scale to 200 Watts.

MFJ-818 Mobile SWR/Wattmeter Instruction Manual

4

Meter Calibration (cont.)

7. With the POWER RANGE button pushed out for the 6 Watt reflected scale,

Transmit 2 Watts as indicated on the reference meter. Adjust the LO REF trim

pot to set the reflected power scale to 20 Watts.

8. SWR requires no calibration.

Figure 2: Test Setup

Figure 3: Trim Pot Location (Side View of MFJ-818)

Transmitter/

Transceiver

Standard

Reference

Wattmeter

MFJ-818

Mobile

SWR/

Wattmeter

50-Ohm

Dummy Load

HI FWD

LO REF

HI REF

LO FWD

MFJ-818 Mobile SWR/Wattmeter Instruction Manual

5

Technical Assistance

If you have any problem with this unit first check the appropriate section of this manual.

If the manual does not reference your problem or reading the manual does not solve your

problem, you may call MFJ Technical Service at 662-323-0549 or the MFJ Factory at

662-323-5869. You will be best helped if you have your unit, manual and all information

on your station handy so you can answer any questions the technicians may ask.

You can also send questions by mail to MFJ Enterprises, Inc., 300 Industrial Park Road,

Starkville, MS 39759; by Facsimile (FAX) to 662-323-6551; or by email to

[email protected]. Send a complete description of your problem, an

explanation of exactly how you are using your unit, and a complete description of your

station.

Schematic

Tabla de contenidos

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario