Metronic Zapbox plus Manual de usuario

Digital Terrestrial Receiver

MET28

Item code : 441810

zapbox plus

RS232

[email protected]

Before installing your ZAPBOX Plus it is important that you read and

understand the instructions completely.

Remember that contact with 230V AC mains can be lethal or can cause severe

electric shock. To avoid this risk :

• Never remove the top cover of the receiver. There are no user-

serviceable parts inside it, but there are some high-voltage live parts.

• Never attempt to repair your receiver. Please contact your retailer.

• Make sure all electrical connectors are properly made.

• Do not place your receiver close to sources of heat, such as heater

or direct sunlight.

• Do not put anything on your receiver which might drip or spill onto it.

• Never place the product near objects filled with water.

• Do not use a liquid form to clean your receiver or remote. A dry cloth

will be sufficient.

If you come across a word that you do not understand, please refer to the

Glossary at the end of this manual.

Your receiver only has one tuner, meaning that you cannot record a channel

other than the one you are watching.

The remote requires two AAA 1.5V batteries. Ensure they are placed correctly.

Please do not dispose of used batteries in your domestic bins. You should

bring them back to your point of sale and place them in the right container.

WARNING - IMPORTANT

ASSISTANCE AND ADVICE

THIS PRODUCT HAS A 12-MONTH WARRANTY FROM THE

DATE OF PUCHASE. DURING THIS PERIOD, IN AN EVENT OF

ANY PROBLEMS, PLEASE RETURN TO THE RETAILER WITH

PROOF OF PURCHASE.

[email protected].

Programming the receiver is achieved through the various menus.

In order to make this manual easier to understand, we will describe

accessing a menu as shown below :

Go to MENU / Setup / Service Setup / xxxx / Manual Scan.

This means :

• Press the MENU key to access the main menu.

• Press the  arrow to select Setup.

• Press OK to confirm.

• Press the  arrow to select Service Setup.

• Press OK to confirm.

• Enter the 4 digit PIN code (0000 on purchase).

• Press the  arrow to select Manual Scan and confirm by

pressing OK.

• Note that words written in bold letters are those you can see on the

TV screen.

This symbol indicates that the

product must not be treated as

household waste. The harmfull

substances possibly contained in

the equipment may have

negative consequences on the environment

and / or the human health. At the end of its

life, bring any electronic equipment back to

your retailer or at the collection point that

your city or town puts at your disposal.

[email protected]

INDEX

1 Installation 06

2 Remote description 10

3 Receiver description 12

4 Daily use 13

5 Personalising the channels listing 13

6 Parental lock 15

7 Resetting the receiver 16

8 Adjusting the TV signal 17

9 Radios 17

10 Channel Search 17

11 Using the receiver with a VCR 18

A - Programming 18

B - Connecting 19

12 TV guide 20

13 What to do if you experience a reception problem 21

14 Glossary 23

15 Multiplexes - channels 24

16 Channels list 25

[email protected].

1 - Installation

A - Simplified installation

As the receiver is not yet plugged into the main source, connect the antenna

directly to the ANT input of the receiver. Connect the TV to the TV scart outlet

of the receiver. Switch on the TV and connect the receiver to the main source.

Insert the batteries in the remote.

A red indicator appears on the

receiver. Press the ON/OFF

key of the remote. The green

indicator will light on and the

welcome screen appears on the

screen. If this is not the case, you

should double-check the scart

connections and or force the A/V

or EXT mode of your TV (refer

to the TV manual). Press OK to

start the installation.

The automatic channels lookup

should start. At the end, the first

channel will appear, meaning the

standard installation is done.

At the bottom of the screen, an

estimation of the remaining time

is displayed. Allow one or two

minutes for the receiver gives a

reliable estimation.

If the search has

not found all channels (or none), this probably means that you need

to better the installation (see next paragraph). If no channels

are found after you have done so, this probably means that you area

is not covered by Free To View.

[email protected]

OPTIONAL

MANDATORY

Screened cable. Replace in case of poor reception by

a high quality cable.

By connecting the TV and the receiver, you will keep the analogue channels

on your TV. You can then record a digital channel whilst watching another

analogue channel.

Installation of the remote extender :

Your zapbox Plus is provided with an infrared extender that allows you to hide

the unit behind the TV set or behind the TV furniture, maintaining the possibility

to control it with the remote controller. Note : you can use use your zapbox

normally without the remote extender.

Connect the extender’s plug on the hole marked IR. Stick the extender on the

side of the TV set, or behind it, paying attention that the wire runs backward.

Before you definitively stick the extender, check that the place you have

chosen allow to correctly operate the remote controller, with a comfortably

wide angle.

[email protected].

B - Wedging / adjusting the aerial

If no channels have been found through your current antenna, it means

that it probably is pointing towards an analogue only transmitter. If your area

is covered by digital, it means that the programs are coming from another

transmitter. You will hence have to adjust the antenna. There are two possible

options, as follows :

Option 1

You know at least one network number (between 21 and 69) used

in your area.

• Go to Menu / Setup / Service Setup

/ xxxx / Manual Scan.

• Press the  arrow until the number

of the UHF network that emits digital

channels appears (see channels list

page 25).

• On TxMode, select 2k with

the arrow.

• On Guard Interval , select 1/32 with

the arrow.

• Wait for a few seconds and monitor

the Quality and Level graphs.

• Swivel the antenna to maximise reception. When you get near the emitter,

the Signal Level should increase, and then the Quality. 6 is the lowest

number for a stable image. If the Level does not increase, this means that

you have chosen an incorrect network number, or that the emission is too far

from your antenna.

• Once you have reached the maximum Level / Quality, screw the antenna

tightly.

• Press EXIT.

• Go to Menu / Setup / Service Setup / xxxx / Fullscan Replace Existing

Services.

[email protected]

Option 2

You are able to receive national channels in analogue and you have no idea

what you can receive in digital quality.

If you are certain that you can receive additional channels, but you do

not know which network is used for these channels, we advise that

you do the following :

Find an UHF antenna with high gain (at least 15 dB) and connect it to

the ANT input of the receiver. Adjust the antenna so it is in the same

position as the previous one and start an automatic channels search

(Go to Menu / Setup / Service Setup / xxxx / Fullscan Replace Existing

Services).

If you find channels that you were unable to receive with your previous

antenna, simply replace it with the new one. Otherwise, swivel the antenna 1/8

of a turn and start another automatic search. As long as you do not find any

channels, continue the same process. You should end up receiving at least

a few channels.

• Find one of the new channels received.

• Go to Menu / Setup / Service Setup / xxxx / Manual Scan.

• At the bottom of the screen, you can view the reception level and quality.

• Turn the antenna to optimise the quality and level (quality must be

at least 6).

• Screw the antenna tightly.

• Press Menu to go back to the previous menu.

• Make an automatic search (Go to Menu / Setup / Service Setup / xxxx /

Fullscan Replace Existing Services).

[email protected].

2 - Remote Description

1 2 3

45 6

060810

PAUSE

EXIT

TV/R

AUDIO

INFO

M/P TXT S-T

P

P

V

V

EPG

LIST

FAV

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Receptor de Metronic

Metronic

Metronic Touch Box 4 Manual de usuario

Metronic

Metronic Eco zapbox 2 Manual de usuario

Metronic

Metronic Sat HD 100 Guía de instalación

Metronic

Metronic Zapbox Gemini Twin Tuner Manual de usuario

Metronic

Metronic TouchBOX 3 Manual de usuario

Metronic

Metronic TouchBox 8 Manual de usuario

Metronic

Metronic ECO Zapbox Manual de usuario

Metronic

Metronic Zapbox 441803 Manual de usuario

Metronic

Metronic Freesat HD Guía de inicio rápido

Metronic

Metronic ReplayBox 441550 Manual de usuario

Metronic

Metronic Zapbox twin 5 Manual de usuario

Metronic

Metronic zapbox twin Manual de usuario

Metronic

Metronic Dualstream Box Manual de usuario

Metronic

Metronic ESPN Sports Manual de usuario

Metronic

Metronic Sat HD 100 441827 Manual de usuario

Metronic

Metronic AccessBox Manual de usuario

Metronic

Metronic ZAPBOX HD DVB-T2 Manual de usuario

Metronic

Metronic DualstreamBOX Manual de usuario

Metronic

Metronic DV3 Manual de usuario

Manuales populares de Receptor de otras marcas

Garmin

Garmin GA 23 Manual de usuario

Aiphone

Aiphone PS-12F Manual de usuario

IMES

IMES TCS-01CA-PMI Manual de usuario

BWI Eagle

BWI Eagle AIR-EAGLE SR Manual

AMIMON

AMIMON AMN12310 WHDI Manual de usuario

Dual

Dual DMCPA79BT Instrucciones de funcionamiento

Sound Associates

Sound Associates SA652P Manual de usuario

Sherwood

Sherwood NewCastle R-772 Manual de usuario

Audio

Audio A10-RX Series Manual de usuario

AllSee

AllSee PushShare PSRV1.1 Manual de usuario

DEMAG

DEMAG DRC-DR D2 Manual de usuario

Teleco

Teleco TVRCL868A02 Manual de usuario

Bosch

Bosch RF3222E Manual de usuario

Kramer

Kramer 631R Manual de usuario

Xpress

Xpress xmc10 Manual de usuario

JVC

JVC KD-MR1BTS Manual de usuario

Omega Engineering

Omega Engineering UWTC-REC3 Manual de usuario

e-survey

e-survey E300 Pro Manual de usuario

Metronic zapbox plus Manual de usuario

Manuales populares de Receptor de otras marcas