Metra Electronics 99-7520B Manual de usuario

METRA. THE WORLD’S BEST KITS.™

APPLICATIONS

1-800-221-0932 metraonline.com

INSTALLATION INSTRUCTIONS FOR PART 99-7520B

Panel Removal Tool • Phillips Screwdriver • Small Flat Blade Screwdriver

TOOLS REQUIRED

Mazda CX7 2010-up

99-7520B

B C

• A) Radio Housing • B) ISO Trim Plate • C) ISO Brackets • D) DDIN Trim Plate

• E) DDIN Brackets • F) Pocket

KIT FEATURES

KIT COMPONENTS

• DIN radio provision with pocket

• ISO radio provision with pocket

• Double DIN radio provision

• Painted matte black to match factory

WIRING & ANTENNA CONNECTIONS (Sold Separately)

• 70-7903T - Mazda Service T-harness 2007-up

• 40-HD10 - Antenna Adapter

Table of Contents

Dash Disassembly

– Mazda CX7 2010-up 3-4

Kit Assembly

– Kit preparation 5

– DIN head unit provision 6

– ISO DIN head unit provision 7

– Double DIN head unit provision 8

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by

enrolling in the most recognized and respected

mobile electronics school in our industry.

Log onto www.installerinstitute.com or call

800-354-6782 for more information and take steps

toward a better tomorrow.

Metra recommends MECP

certified technicians

99-7520B

Caution

Metra recommends disconnecting the negative battery terminal before beginning any

installation. All accessories, switches, and especially air bag indicator lights must be

plugged in before reconnecting the battery or cycling the ignition.

*NOTE: Refer also to the instructions included with the aftermarket radio.

1. Unclip and remove the (2) trim panels

from the left and right side of the radio

trim panel. (Figure A)

2. Unclip and remove the trim panel

surrounding the radio and climate

controls. (Figure B)

3. Remove (4) Phillips screws securing the

radio. (Figure C)

Continued on next page

Dash Disassembly

99-7520B

A/C

(Figure A)

(Figure B)

(Figure C)

99-7520B

Dash Disassembly

5. Remove (2) Phillips screws securing the

hazard switch to the factory radio then

separate the front half from the rear half

of the switch to remove. (Figure D)

Continue to kit preparation

BACK OF FACTORY RADIO

(Figure D)

Kit preparation 99-7520B

1. Secure the hazard switch into the 99-

7520 radio housing using the factory

hardware. (Figure a)

Continue to kit assembly

Kit preparation

(Figure A)

Kit Assembly 99-7520B

DIN head unit provision

(Figure A)

(Figure B)

(Figure C)

1. Locate the factory wiring harness in the

dash. Metra recommends using the

proper mating adapter from Metra or

AXXESS. Re-connect the negative

battery terminal and test the unit for

proper operation.

2 Slide the DIN cage into the radio

housing and secure by bending the

metal locking tabs down. (Figure A)

3. Snap the pocket into the bottom

opening of the radio housing. (Figure B)

4. Slide the aftermarket head unit into the

cage and secure. (Figure C)

5. Reassemble dash in reverse order

of disassembly.

Kit Assembly 99-7520B

ISO DIN head unit provision

(Figure A)

(Figure B)

(Figure C)

1. Locate the factory wiring harness in the

dash. Metra recommends using the

proper mating adapter from Metra or

AXXESS. Re-connect the negative

battery terminal and test the unit for

proper operation.

2 Mount the ISO brackets to the head unit

with the screws supplied with the unit.

(Figure A)

3. Snap the pocket into the bottom

opening of the radio housing. (Figure B)

4 Slide the head unit into the radio

opening until the side clips engage.

(Figure B)

5. Snap the Trim plate into the Radio

Housing. (Figure C)

6. Reassemble dash in reverse order

of disassembly.

Kit Assembly 99-7520B

Double DIN head unit provision

(Figure A)

(Figure B)

(Figure C)

1. Locate the factory wiring harness in the

dash. Metra recommends using the

proper mating adapter from Metra or

AXXESS. Re-connect the negative

battery terminal and test the unit for

proper operation.

2 Cut and remove the center bar from the

radio housing. (Figure A)

3. Snap the Double DIN brackets to the

inside edge of the Double DIN trim plate

(Figure B)

4. Slide the Double DIN head unit or

stacked ISO head units into the bracket/

radio housing assembly and secure the

Double DIN head unit or stacked ISO

head units to the assembly using the

screws supplied with the radio.

(Figure C)

5. Snap the double DIN trim plate into the

radio housing. (Figure C)

6. Reassemble dash in reverse order

of disassembly.

Notes

Tabla de contenidos

Otros manuales de Sistema estéreo para automóvil de Metra Electronics

Metra Electronics

Metra Electronics 95-8903S Manual de usuario

Metra Electronics

Metra Electronics 99-7320 Manual de usuario

Metra Electronics

Metra Electronics 99-3309B-LC Manual de usuario

Metra Electronics

Metra Electronics Car Stereo System Manual de usuario

Metra Electronics

Metra Electronics 95-7309 Manual de usuario

Metra Electronics

Metra Electronics 95-7309 Manual de usuario

Metra Electronics

Metra Electronics 95-7322 Manual de usuario

Metra Electronics

Metra Electronics AW-586FT Manual de usuario

Metra Electronics

Metra Electronics 99-7378B Manual de usuario

Metra Electronics

Metra Electronics 99-7346B Manual de usuario

Metra Electronics

Metra Electronics 95-7504 Manual de usuario

Metra Electronics

Metra Electronics 95-1005 Manual de usuario

Metra Electronics

Metra Electronics 95-7354 Manual de usuario

Metra Electronics

Metra Electronics 95-3003G Manual de usuario

Metra Electronics

Metra Electronics 99-8218 Manual de usuario

Metra Electronics

Metra Electronics 99-7367 Manual de usuario

Metra Electronics

Metra Electronics 99-7335S Manual de usuario

Metra Electronics

Metra Electronics 99-5807 Manual de usuario

Metra Electronics

Metra Electronics 99-5812 Manual de usuario

Metra Electronics

Metra Electronics 99-8213 Manual de usuario

Metra Electronics

Metra Electronics 99-7018 Series Manual de usuario

Metra Electronics

Metra Electronics 95-3305 Manual de usuario

Metra Electronics

Metra Electronics 99-6505 Manual de usuario

Metra Electronics

Metra Electronics 99-7603 Manual de usuario

Manuales populares de Sistema estéreo para automóvil de otras marcas

JL Audio

JL Audio Stealthbox SB-CAN-G2MVX3D/10TW3 Manual de usuario

Clarion

Clarion PU-9836A Manual de usuario

Sony

Sony MEX-BT5750U Manual de usuario

Mitsubishi Electric

Mitsubishi Electric AR0M Manual de usuario

Sony

Sony RM-X7BT Manual de usuario

Insignia

Insignia NS-HD5113 Manual de usuario

Clarion

Clarion BTD3341 Manual de usuario

USA SPECS

USA SPECS PA11-VW6 Manual de usuario

Sony

Sony MEX-N4380BT Manual de usuario

Kenwood

Kenwood KCD-BT6544U/UY Manual de usuario

JVC

JVC KD-DB912BT Manual de usuario

Philips

Philips CSQ405/98 Manual de usuario

Alpine

Alpine TDM-7544 Manual de usuario

Autotek

Autotek TransAm TA 1400 Manual de usuario

Clarion

Clarion PN-3124N-A Manual de usuario

Denso TEN

Denso TEN FT0108A Manual de usuario

Pyle

Pyle PLD57MU Manual de usuario

Harman

Harman Chrysler Radio Navigation System RB4 Manual de usuario