Metra Electronics 99-7367 Manual de usuario
METRA. The World’s best kits.™metraonline.com © COPYRIGHT 2016 METRA ELECTRONICS CORPORATION
REV. 6/20/2016 INST99-7367
Installation instructions for part 99-7367
CAUTION!
All accessories, switches, climate controls panels,
and especially air bag indicator lights must be connected before
cycling the ignition. Also, do not remove the factory radio with
the key in the on position, or while the vehicle is running.
• ISO DIN radio provision with pocket
• ISO DDIN radio provision
• Factory clock and push to start provision
• 99-7367B - Painted matte black
• 99-7367HG - Painted gloss black
• A) Radio housing trim panel • B) Radio brackets • C) Vent trim ring • D) Pocket • E) Start/Stop switch blank plate
• F) Storage pocket • G) (8) #8 x 3/8” Phillips screws
KIT COMPONENTS
KIT FEATURES
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • 70-7304
Antenna Adapter: • Not required
• Panel removal tool • Phillips screwdriver
TOOLS REQUIRED
Kia Rio 2016-up
99-7367 Dash Disassembly .............................................. 2-3
Kit Preparation........................................................4
Kit Assembly
–ISO DIN radio provision with pocket ....................... 5
–ISO DDIN radio provision ....................................... 6
Table of Contents
AB DC E F G
99-7367
2
1. Unclip and remove the factory
radio trim panel including the a/c
vents. (Figure A)
Note: Remove the (8) retaining
clips to be reused in Kit Assembly.
2. Remove (4) Phillips screws
securing the radio in the dash.
Continued on the next page
Dash Disassembly
(Figure A)
99-7367
3
3. Remove (2) Phillips screws
securing the start/stop switch if
equipped. (Figure B)
4.
Remove (4) Phillips screws securing
the storage pocket, or factory clock
if equipped. (Figure B)
5. Remove the (6) Phillips screws
securing the a/c vents then unclip
and remove them from the radio
trim panel. (Figure B)
6. Unclip and remove the hazard
switch. (Figure B)
Continue to kit preparation
Dash Disassembly
(Figure B)
Step 3
Step 4
Step 5
Step 6
99-7367
4
1. Place the vent trim ring into the
radio housing trim panel and
mount the vents using the factory
screws removed in disassembly.
Mount the clock and hazard
switch into the radio housing trim
panel using screws removed in
disassembly.
(Figure A)
Note: If no factory clock is present,
a storage pocket and (4) # 8 x 3/8”
Phillips screws are provided.
2. Mount the start/stop switch or
blank plate depending on your
application into the radio housing
trim panel.
Note: If no switch is present there
are (2) #8 X 3/8” Phillips screws
supplied to mount the blank plate.
3. Install the (8) panel clips removed
in disassembly onto the
radio
housing trim panel
.
Continue to kit assembly
Kit Preparation
(Figure A)
99-7367
Kit Assembly
(Figure A) (Figure B)
ISO DIN radio provision with pocket
1. Mount the pocket to the radio
brackets with the (2) #8 x 3/8”
Phillips screws supplied. (Figure A)
2.
Remove the metal DIN sleeve and
trim ring from the aftermarket radio
.
3. Slide the radio between the radio
brackets and secure with screws
supplied with the radio. (Figure B)
4. Locate the factory wiring harness
in the dash. Metra recommends
using the proper mating adapter
from Metra or AXXESS. Re-connect
the negative battery terminal and
test the radio for proper operation.
5. Reassemble the dash in reverse
order of disassembly.
5
99-7367
Kit Assembly
(Figure A)
ISO DDIN radio provision
1. Mount the radio brackets to the
radio with the screws supplied with
the radio. (Figure A)
2. Locate the factory wiring harness
in the dash. Metra recommends
using the proper mating adapter
from Metra or AXXESS. Re-connect
the negative battery terminal and
test the radio for proper operation.
3. Reassemble the dash in reverse
order of disassembly.
6
99-7367
7
METRA. The World’s best kits.™metraonline.com © COPYRIGHT 2016 METRA ELECTRONICS CORPORATION
REV. 6/20/2016 INST99-7367
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
Installation instructions for part 99-7367
IMPORTANT
If you are having difficulties with the installation
of this product, please call our Tech Support line
at 1-800-253-TECH. Before doing so, look over
the instructions a second time, and make sure
the installation was performed exactly as the
instructions are stated. Please have the vehicle
apart and ready to perform troubleshooting
steps before calling.
INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-7367
METRA. The World’s best kits.™metraonline.com1-800-221-0932 © COPYRIGHT 2016 METRA ELECTRONICS CORPORATION
REV. 6/20/2016 INST99-7367
¡PRECAUCIÓN! Todos los accesorios, interruptores, paneles de
Controles de temperatura interior, y especialmente las luces
indicadoras de bolsas de aire deben estar antes de un ciclo del
encendido. Además, no se retire el radio de fábrica con la llave en
la posición de encendido, o mientras el vehículo está en marcha.
Indice
• Provisión de radio ISO DIN con cavidad
• Provisión de radio ISO DDIN
• Reloj de fábrica y provisión de botón de arranque
• 99-7367B - Pintura de negra mate
• 99-7367HG - Pintura negro brillante
• A) Panel de la moldura de la carcasa del radio • B) Soportes del radio • C) Anillo de moldura de las rejillas • D) Cavidad
• E) Placa vacía del interruptor de inicio/paro • F) Bolsillo de almacenamiento • G) (8) tornillos Phillips #8 de 3/8”
COMPONENTES DEL KIT
CARACTERÍSTICAS DEL KIT
CABLEADO Y CONEXIONES DE ANTENA (se venden por separado)
Arnés de cables: • 70-7304
Adaptador de antena: • No requerido
• Herramienta para quitar paneles • Destornillador Phillips
HERRAMIENTAS REQUERIDAS
Kia Rio 2016 y mas
99-7367
AB DC E F G
Desmontaje del tablero ...................................... 2-3
Preparación del kit .................................................4
Ensamble del kit
–Provisión de radio ISO DIN con cavidad.................. 5
–Provisión de radio ISO DDIN .................................. 6
99-7367
Desmontaje del tablero
2
(Figura A)
1. Desenganche y quite el panel de
la moldura del radio de fábrica,
incluyendo las rejillas del aire
acondicionado. (Figura A)
Nota: Quite los (8) ganchos de
retención que se volverán a usar
en el ensamble del kit.
2. Quite los (4) tornillos Phillips que
sostienen el radio en el tablero.
Continúa en la siguiente página
Otros manuales para 99-7367
1
Tabla de contenidos
Idiomas:
Otros manuales de Sistema estéreo para automóvil de Metra Electronics
Metra Electronics
Metra Electronics 99-8218 Manual de usuario
Metra Electronics
Metra Electronics 99-5814 Manual de usuario
Metra Electronics
Metra Electronics 99-3000 Manual de usuario
Metra Electronics
Metra Electronics 95-3003G Manual de usuario
Metra Electronics
Metra Electronics 99-5822B Manual de usuario
Metra Electronics
Metra Electronics 95-8903S Manual de usuario
Metra Electronics
Metra Electronics 99-9011 Manual de usuario
Metra Electronics
Metra Electronics 99-7009 Manual de usuario
Metra Electronics
Metra Electronics 99-8219 Manual de usuario
Metra Electronics
Metra Electronics 99-7378B Manual de usuario
Metra Electronics
Metra Electronics 95-7309 Manual de usuario
Metra Electronics
Metra Electronics 99-6505 Manual de usuario
Metra Electronics
Metra Electronics 99-3309B-LC Manual de usuario
Metra Electronics
Metra Electronics 99-8213 Manual de usuario
Metra Electronics
Metra Electronics 99-8239B Manual de usuario
Metra Electronics
Metra Electronics 95-9607B Manual de usuario
Metra Electronics
Metra Electronics 99-7320 Manual de usuario
Metra Electronics
Metra Electronics 95-7870G Manual de usuario
Metra Electronics
Metra Electronics 99-7603 Manual de usuario
Metra Electronics
Metra Electronics 89-9400 Manual de usuario
