Metra Electronics 99-7524B Manual de usuario

Installation instructions for 99-7524B

REV. 9/23/2015 INST99-7524B

Table of Contents

CAUTION!

Metra recommends disconnecting the negative bat

tery terminal before beginning any installation, unless the vehicle

manufacturer recommends against so. Please check with your local

Dealership for more information. All accessories, switches, climate

controls panels, and especially air bag indicator lights must be con-

nected before reconnecting the battery or cycling the ignition. Also,

do not remove the factory radio with the key in the on position, or the

vehicle running. It would be best to remove the key from the ignition

and then wait a few seconds before removing the factory radio.

20;*64765,5;:

• ISO DIN radio provision with pocket

• ISO DDIN radio provision

• Painted charcoal black

20;-,(;<9,:

>0905.(5;,55(*655,*;065: (sold separately)

Wiring Harness: • Included with kit

Antenna Adapter: • Not required

• Panel removal tool • Phillips screwdriver

• 10mm Socket wrench

;663:9,8<09,+

Mazda 6 2006-2008

99-7524B

Dash Disassembly .............................................. 2-4

Kit Preparation

–Electronic climate control..................................... 5

–Manual climate control......................................... 6

–Felt tape application............................................. 7

Kit Assembly

–ISO DIN radio provision with pocket...................... 8

–ISO DDIN radio provision ...................................... 8

Wiring Installation ..................................................9

Installing the 99-7524B ........................................10

Display customization..........................................11

• A) Radio/climate control panel • B) Radio brackets • C) Pocket • D) (4) #8 x 3/8” Phillips screws

• E) (6) Panel clips • F) (2) #8 x 1” Phillips screws • G) Harness • H) Manual climate harness

99-7524B

Electronic climate control

1. Unscrew the shift knob counter

clockwise to remove. (Figure A)

2. Unclip and remove the cup holder/

parking brake cover and shifter

cover as one radio. (Figure B)

3. Remove (2) Phillips screws from

the bottom of the radio/climate

control panel. (Figure C)

4. Open glove box, squeeze sides

together and let open fully then

remove (1) 10mm bolt from the

side of the radio bracket.

(Figure D)

Dash Disassembly

Rear of Electronic Climate Control

Rear of Radio/Climate Control Panel

INSIDE

GLOVE BOX

(Figure B)

(Figure F)

(Figure E)

(Figure C)

(Figure G)

(Figure D)(Figure A)

5. Unsnap and remove radio/climate

control panel including climate

control vents at the top. (Figure E)

6. Remove (4) Phillips screws

securing vents to radio/climate

control panel to remove. (Figure F)

7. Remove (8) Phillips screws

securing the electronic climate

control to the radio/climate control

panel to remove. (Figure G)

Continue to kit preparation

99-7524B

Manual climate control

1. Unscrew the shift knob counter

clockwise to remove. (Figure A)

2. Unclip and remove the cup holder/

parking brake cover and shifter

cover as one radio. (Figure B)

3. Remove (2) Phillips screws from

the bottom of the radio/climate

control panel. (Figure C)

4. Pull the climate control knobs off

and remove (2) Phillips screws

from behind knobs. (Figure D)

Dash Disassembly

(Figure B)

(Figure F)

(Figure A)

(Figure E)

(Figure C)

(Figure G)

(Figure D)

5. Open glove box, squeeze sides

together and let open fully then

remove (1) 10mm bolt from the

side of the radio bracket. (Figure E)

6. Unsnap and remove radio/climate

control panel including climate

control vents at the top. (Figure F)

7. Remove (4) Phillips screws

securing vents to radio/climate

control panel to remove. (Figure G)

Continue on the next page

INSIDE

GLOVE BOX

A/C

99-7524B

Manual climate control (continued)

8. Remove the (2) small Phillips

screws securing the light bulb

boards on each side of the

backlight dispersion bar.

Note: Notice how they are

positioned in the backlight

dispersion bar as they will be

placed in the 99-7524B the same

way. (Figure H)

9. Remove (4) Phillips screws

securing backlight dispersion bar

and knob trim bezels. (Figure I)

10. Push the bottom edges of the knob

trim bezels from the front side to

the back and slide both pieces out

as one radio. (Figure J)

Continue to kit preparation

Dash Disassembly

(Figure H) (Figure J)

(Figure I)

99-7524B

Kit Preparation

Electronic climate control

1. Clip the climate control knob outer trim ring panel

into the 99-7524B housing. (Figure A)

2. Align the screw holes in the climate control and the

radio housing panel then push the climate control

onto the radio housing panel. (Figure B)

3. Secure the climate control with the factory

hardware removed in step 7 of the dash

disassembly for electronic climate control cars.

4. Unclip and remove the small oval cover plate at the

bottom center of the factory radio and insert into

the 99-7524B radio housing. (Figure C)

5. Attach (6) panel clips supplied to the radio

housing.

Note: The light bulb boards will not be used with

auto climate control vehicles disregard these bulbs.

(Figure B)

REAR VIEW OF ELECTRONIC CLIMATE CONTROL

(Figure A) (Figure C)

99-7524B

Kit Preparation

Manual climate control

1. Put the climate control knob

outer trim panel and the backlight

dispersion bar together and clip

into the radio housing panel as

one radio.

Note: You may have to push down

slightly on the middle of the radio

to ease in positioning it into the kit.

(Figures A, B, C)

2. Secure the radio with the factory

hardware previously removed from

the manual climate control

dash disassembly.

3. Secure the light bulb boards

on each side of the backlight

dispersion bar using the factory

hardware removed in step 8 in

manual climate control dash

disassembly. (Figure D)

4. Unclip and remove the small oval

cover plate at the bottom center of

the factory radio and insert into the

99-7524B radio housing.

(Figure E)

5. Attach (6) panel clips supplied to

the radio housing.

(Figure D)(Figure B)

(Figure E)(Figure C)(Figure A)

ASSEMBLED

INSTALLED

99-7524B

Kit Preparation

Felt tape application

Note: Due to differences in factory

tolerances you may need to apply the

provided felt tape to the edge of the

99-7524B radio housing to relieve

backlight bleed through.

1. Looking at edge of radio housing

apply felt tape to inner edge (toward

back of kit). If it is positioned to

closely to the outer edge you may be

able to see it once it is in the dash.

(Figure A)

Apply to back of both sides

99-7524B

Kit Assembly

ISO DIN radio provision with pocket

1. Mount the pocket to the radio

brackets with (4) #8 x 3/8” Phillips

screws supplied. (Figure A)

2. Remove the metal DIN sleeve and

trim ring from the aftermarket

radio.

3. Slide the radio into the bracket/

pocket assembly, and then secure

with the screws supplied with the

radio. (Figure B)

Continue to the Wiring Installation

ISO DDIN radio provision

1. Attach the radio brackets to the

radio using the screws supplied

with the radio. (Figure A)

Continue to the Wiring Installation

(Figure A)

(Figure B)

(Figure A)

99-7524B

Wiring Installation

Connections to be made to the aftermarket radio:

• Connect the Black wire to the ground wire.

• Connect the Yellow wire to the battery wire.

• Connect the Red wire to the accessory wire.

• Connect the Orange wire to the illumination wire. If the aftermarket

radio has no illumination wire, cap off the Orange wire.

•

Cap off and disregard the Orange/White wire, it will not be used in this

application.

• Connect the Blue wire to the antenna turn on wire.

•

Connect the Blue/White wire to the amp turn-on wire, if the vehicle is amplified

• Connect the White wire to the left front positive speaker output.

• Connect the White/Black wire to the left front negative speaker output.

• Connect the Gray wire to the right front positive speaker output.

• Connect the Gray/Black wire to the right front negative speaker output.

• Connect the Green wire to the left rear positive speaker output.

• Connect the Green/Black wire to the left rear negative speaker output.

• Connect the Purple wire to the right rear positive speaker output.

•

Connect the Purple/Black wire to the right rear negative speaker output.

• 12-pin pre-wired ASWC-1 harness:

This harness is to be used along with the optional ASWC-1 (not included)

to retain steering wheel audio controls. If the ASWC-1 is not being used,

disregard this harness. If it will be used, please refer to the ASWC-1

instructions for radio connections and programming.

Note: Disregard the harness that comes with the ASWC-1.

99-7524B

Connection Legend

(99-7524 radio housing diagram)

*Note: Location 2 will not be used in this application.

Location 1Location 3

*Location 2

Installing the 99-7524B

1. Connect the 8-pin connector supplied, into Location 1, on the back of the radio/

climate-control housing. (see Connection Legend)

Note: If this connector is not plugged in, the kit will not operate.

2. For manual climate control vehicles only, connect the 16-pin connector

supplied, into Location 3, on the back of the radio/climate-control housing.

(see Connection Legend)

3. Locate the factory wiring harness and antenna connector in the dash, and

complete all necessary connections to the radio.

4. Mount the completed assembly into the dash, and then reassemble the dash in

reverse order of disassembly, using the 99-7524B radio/climate panel.

Note: There are no existing holes for mounting the radio. New holes will need

to be made using (2) #8 x 1” Phillips screws supplied . The radio brackets will

rest on a shelf in the sub-dash. Be sure the radio is level and centered while

mounting the completed assembly into the dash opening.

5. Start the car and test all the climate control functions.

Note: The air recirculation light will be on at initial startup and will not go out

until using the climate controls for the first time.

Otros manuales para 99-7524B

Tabla de contenidos

Otros manuales de Accesorios para automóviles de Metra Electronics

Metra Electronics

Metra Electronics 99-8225G Manual de usuario

Metra Electronics

Metra Electronics 95-9308B Manual de usuario

Metra Electronics

Metra Electronics 99-5850B Manual de usuario

Metra Electronics

Metra Electronics 99-7423 Manual de usuario

Metra Electronics

Metra Electronics 99-7402 Manual de usuario

Metra Electronics

Metra Electronics 99-9000 Manual de usuario

Metra Electronics

Metra Electronics MAZDA 6 2009 99-7511S Manual de usuario

Metra Electronics

Metra Electronics 82-3043 Manual de usuario

Metra Electronics

Metra Electronics 99-7503 Manual de usuario

Metra Electronics

Metra Electronics 95-7378B Manual de usuario

Metra Electronics

Metra Electronics MAZDA CX7 2007-09 99-7508 Manual de usuario

Metra Electronics

Metra Electronics 99-8711 Manual de usuario

Metra Electronics

Metra Electronics 99-7477 Manual de usuario

Metra Electronics

Metra Electronics 87-99-3052 Manual de usuario

Metra Electronics

Metra Electronics AFDI-RSE-01 Manual de usuario

Metra Electronics

Metra Electronics 99-7340B Manual de usuario

Metra Electronics

Metra Electronics 99-4644 Manual de usuario

Metra Electronics

Metra Electronics 95-8224 Manual de usuario

Metra Electronics

Metra Electronics 108-FD7B Manual de usuario

Metra Electronics

Metra Electronics 95-9012 Manual de usuario

Metra Electronics

Metra Electronics 99-6506 Manual de usuario

Metra Electronics

Metra Electronics 99-8227S Manual de usuario

Metra Electronics

Metra Electronics 99-8234 Manual de usuario

Metra Electronics

Metra Electronics 99-3301 Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario