METHVEN Maku Manual de usuario

Issue A436920

TECHNICAL SPECIFICATIONS

Operating Pressure:

Unequal Pressure:

Hot: Min 35kPa.

Cold: Min 300kPa.

Equal Pressure:

Min 35kPa.

If supply exceeds 500kPa a pressure

limiting valve must be installed.

Operating Temperature:

Hot: Min 55°C (at mixer), Max 80°C.

Cold: Min 5°C.

NB: New Zealand Building Code Clause G12 -

Water Supplies speciﬁes all outlets used

primarily for personal hygiene shall deliver

water at a safe temperature.

Inlet Connections:

All ½" BSP.

Methven warrants this product against manufacturing defects and that it is suitable for use

under the operating conditions speciﬁed in this instruction sheet.

For your warranty please refer to www.methven.com or call Customer Service

New Zealand

0800 804 222

Australia

1300 638 483

0800 195 1602

Unequal Pressure Systems

1. If the system is supplied by a pressure pump, ensure that the pump can maintain

300kPa at the cold Inlet. If not, install a low pressure cold feed and install the

mixer as if for a low pressure equal system.

2. If the Cold pressure is ABOVE 400kPa, install the mixer without modiﬁcation.

(i.e. with red nozzle as factory ﬁtted.)

3. If the Cold pressure is BELOW 400kPa, replace the Red Nozzle with the Blue Nozzle

supplied in the carton.

a) To remove a nozzle from the mixer body ﬁt a 6mm Allen key into the hexagon

outlet of the nozzle and turn anti-clockwise until the nozzle comes free of

the mixer body.

b) Fitting a nozzle is the reverse procedure to removal. The nozzle is in the

correct position when approximately 2mm of the nozzle protrudes from

the outlet of the mixer. Do not use excessive force when ﬁtting the nozzle, it

should turn freely. Screw in until just tight and then unscrew ½ a turn.

Equal Pressure Systems

Remove and discard nozzle from mixer.

JET SELECTION MAKU SHOWER MIXER WITH FASTFLOW

INSTALLATION GUIDE

Allen Key

Refer to back page for correct nozzle selection

Lever handle

Grub screw

Faceplate

Screws

Body assembly

Nozzle

Refer to back page for

correct nozzle selection

Faceplate Cover

Do not discard screws

Hole cutout

102mm

Distance from mounting stud

to front of lining:

- Min 48mm

- Max 72 mm

Hot

Cold

Min 450mm

straight run

IMPORTANT

Please read all of the instructions before installation

Avoid restrictive piping, ﬁttings or sharp angled bends when plumbing the mixer.

Do not hydrostatic test the installation with this mixer installed. Damage to the ceramic

cartridge may occur.

All pipe-work must be thoroughly ﬂushed prior to installation of the mixer. In-line ﬁlters must

be installed on both hot and cold supplies to prevent foreign particles damaging the ceramic

cartridge.

NOTE: It is the responsibility of the installer to ensure a water proof seal is achieved

between the faceplate and ﬁnished surface of the wall. If in any doubt about the quality

of the seal the faceplate seal should be removed and then reinstalled using silicon to

ensure a seal is achieved.

O-ring

Otros manuales de Producto de plomería de METHVEN

METHVEN

METHVEN 01-2138 Instrucciones de funcionamiento y mantenimiento

METHVEN

METHVEN SATINJET ESCAPE MKII Manual de usuario

METHVEN

METHVEN KIRI Manual de usuario

METHVEN

METHVEN Maku 01-8567 Manual de usuario

METHVEN

METHVEN Kiri 01-5436 Manual de usuario

METHVEN

METHVEN Kaha 01-7003 Manual de usuario

METHVEN

METHVEN 01-8840 Manual de usuario

METHVEN

METHVEN AURAJET HANDSET Manual de usuario

METHVEN

METHVEN 03-9470M Manual de usuario

METHVEN

METHVEN Kaha 01-7300 Manual de usuario

METHVEN

METHVEN KIRI KIWSLCP Manual de usuario

METHVEN

METHVEN WAIPORI BASIN MIXER Manual de usuario

METHVEN

METHVEN MK2 Manual de usuario

METHVEN

METHVEN KIRI SATINJET 13-7602 Manual de usuario

METHVEN

METHVEN MAKU Manual de usuario

METHVEN

METHVEN Deva NCT002 Manual de usuario

METHVEN

METHVEN KIRI MK2 Manual de usuario

METHVEN

METHVEN Deva DLT095 Manual de usuario

METHVEN

METHVEN 01-2053 Manual de usuario

METHVEN

METHVEN AURAJET HANDSET Manual de usuario

METHVEN

METHVEN 03-9234M Manual de usuario

METHVEN

METHVEN FUTURA Manual de usuario

METHVEN

METHVEN 03-9432M Manual de usuario

METHVEN

METHVEN Kaha 01-7409 Manual de usuario

Manuales populares de Producto de plomería de otras marcas

Weka

Weka 506.2020.00E Instrucciones de funcionamiento

Kohler

Kohler K-6228 Instrucciones de montaje

UBERHAUS DESIGN

UBERHAUS DESIGN 75175017 Manual de usuario

American Standard

American Standard DetectLink 6072121 Manual de usuario

Uponor

Uponor Contec TS Manual de usuario

Pfister

Pfister Selia 49-SL Manual de usuario

Fortis

Fortis VITRINA 6068700 Manual de usuario

Fortis

Fortis MILANO 78211JS Manual de usuario

Kohler

Kohler K-12183 Instrucciones de montaje

Maxxus

Maxxus MX-M206-01 Manual de usuario

Moen

Moen 5922 Series Manual de usuario

Viega

Viega Prevista Pure 8512 Manual de usuario

Kohler

Kohler Centerset K-15240 Instrucciones de montaje

Viega

Viega Prevista Dry 8522.33 Manual de usuario

Sanela

Sanela Lema SLP 59RB Manual de usuario

Elkay

Elkay EDF15AC Manual de instalación

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Manual

baliv

baliv WT-140 Manual de usuario