Messoa NCC800 Manual de usuario
www.messoa.com
5300-00000001-21Y A1
1080p Cube Network Camera
NCC800/NCC800WL
Quick Start Guide
Guia de inicio rápido
Guida rapida
Guide de démarrage rapide
Краткое руководство
クイックスタートガイド
快速安裝指南
快速安装指南
NCC800/NCC800WL lQuick Start Guide 1
English
Safety Instructions
The camera is intended for indoor use. Do not install this camera
outdoors.
Make sure the supplied voltage meets the power consumption
requirements of the camera before powering the camera on.
Incorrect voltage may cause damage to the camera.
The camera should be protected from water and moisture,
excessive heat, direct sunlight and cold.
This installation should be made by a qualied service person and
should conform to all local codes.
Unplug the camera during lightning storms or when unused for
long periods of time.
Copyright
No part of this document may be reproduced or transmitted in any form
or by any means, electronic or mechanical, for any purpose, without
the express written permission of MESSOA.
© 2012 All rights reserved.
Disclaimer
Specications and information contained in this document are
presented as accurately as possible as of the time of release, but
are not guaranteed to be entirely free of error. MESSOA assumes no
responsibility for errors or omissions that may appear in this document
and reserves the right to change this publication at any time without
obligation to notify anyone of such revisions or changes.
2 NCC800/NCC800WL lQuick Start Guide
1. Introduction
Package Contents
1080p Cube Network Camera x1
CD-ROM (User manual and IP Finder utility) x1
Quick Start Guide x1
Power Supply (DC 12V Power Adaptor) x1
Video Cable (2-Pin to BNC Video Out) x1
Bracket for wall/ceiling mount x1
USB Wi-Fi Dongle (for NCC800WL) x1
Hardware Overview
Front and Side View
Microphone
Ethernet LED Wireless LED
Speaker
Infrared LED
Camera Lens
Focus Adjustment Ring
Focus Adjustment
Ring Screw
micro SD/SDHC
card slot
NCC800/NCC800WL lQuick Start Guide 3
English
Rear View
Reset
DC 12V
4
ALM-In +
3
ALM-In -
2
ALM-Out
1
GND
1. Power LED: The LED lights on when power is applied.
2. Video: To perform focus and iris adjustments during the
installation, connect this port to a monitor using provided video
cable.
3. USB Dongle: Optionally connect to a USB Wi-Fi dongle for wireless
function.
4. Ethernet/PoE: Connects to the LAN port of a standard
10Base/100Base-TX device, e.g., hub, switch or router.
5. I/O: Connect your external devices, e.g., sensor and alarms to
the corresponding I/O terminal block. The pins of the I/O terminal
block controls the following signals:
Pin Signal Connection
1 GND Ground (electricity) in electrical circuits.
4 NCC800/NCC800WL lQuick Start Guide
2 ALM-Out Connect to device that responds to alarm
signals.
The camera uses an NMOS transistor with
source connected to GND. If used with an
external relay, a diode must be connected
in parallel with the load to protect against
transient voltages.
3 ALM-IN - Connect to device that triggers alarm signals.
Connect to external power source negative
side (0V) to activate.
4 ALM-IN + Connect to device that triggers alarm signals.
Connect to external power source positive side
(3.3V~5V) to activate.
6. DC 12V: Connect to the provided power adapter.
If you are to use power from Ethernet connection, this connector is
not used.
7. Audio In: Connect to an external microphone
8. Audio Out: Connect to a speaker.
9. Reset: Using a pointed object, hold down the reset button for
about 5 seconds to restart the camera. Or hold down the reset
button for longer than 5 seconds to reset the camera to the factory
defaults.
NCC800/NCC800WL lQuick Start Guide 5
English
2. Installation
2.1 Mounting the Camera
1. Drill three holes at the desired location and insert provided anchors
into the holes. Then fasten the provided screws into the anchors to
secure the camera to the wall.
2. To adjust the camera angle, use a torx key to loosen the two
screws and loosen the knob. After adjustment is done, fasten the
screws and the knob.
Loosen the two screws
and the and knob.
6 NCC800/NCC800WL lQuick Start Guide
2.2 Connecting the Cables
1. Optionally connect alarm input/output devices to the camera.
2. Optionally connect a speaker and microphone to the camera.
3. Connect the camera to a power source, using one of these options:
• DC 12V: Connect to the provided power adapter.
• PoE: Using an Ethernet cable, connect the LAN port to a PoE-
capable network device. Power will be supplied through the
Ethernet cable.
4. Optionally connect a video monitor if you want to perform focus
and iris adjustments during the installation.
5. For NCC800WL, connect the USB Wi-Fi dongle to the USB port of
the camera for wireless capability.
2.3 Adjusting the Focus
Loosen the Focus Adjustment Ring screw rst and then rotate the ring
to adjust the focus. After adjustment, fasten the screw.
3. Initial Conguration
Before connecting the camera to your network infrastructure, or to a
wireless network, you have to connect the camera to a computer
rst to perform initial congurations.
1. Congure the computer’s IP address to one other than the camera’s
default IP address, such as:
• IP Address: 192.168.1.100
• Subnet Mask: 255.255.255.0
2. Usning an Ethernet cable, connect the camera to the computer.
The LAN port of the camera supports auto MDI/MDIX so there is no
need to use a cross-over cable.
NCC800/NCC800WL lQuick Start Guide 7
English
3. On the PC, launch a web browser and enter the IP address of the
camera in the URL eld:
http://192.168.1.30
4. When prompting to login, enter the default user name: admin and
password: 1234 to login. Note that the user name and password
are case-sensitive.
5. Congure the settings to meet your requirements. If you are
going to connect the camera to a wireless network, make sure the
Wi-Fi dongle is connected to the USB connector of the camera.
Then congure the wireless settings under Network > WLAN as
needed. For more information, refer to the User Manual on the
provided CD.
4. Connecting to Your Network
Connecting to a LAN
If you have multiple cameras installed on your network, you can
use the provided IP Finder utility to manage the cameras. For more
information, refer to the User Manual on the provided CD.
Router/Switch/Hub
8 NCC800/NCC800WL lQuick Start Guide
Connecting to a WLAN (for NCC800WL)
After the WLAN conguration is done, you need to unplug the Ethernet
cable from the camera to use the wireless function (as the camera
doesn’t support LAN and WLAN simultaneously).
Wireless AP
Connecting to the Internet
Router
xDSL/Cable
Modem
To enable remote access to the cameras, you must congure your
router/rewall to open port numbers. For more information, refer to the
User Manual on the provided CD.
Otros manuales para NCC800
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Idiomas:
Otros manuales de Cámara de seguridad de Messoa
Messoa
Messoa NDR890 Manual de usuario
Messoa
Messoa NCC800 Manual de usuario
Messoa
Messoa NCB855E Manual de usuario
Messoa
Messoa SCR368-HN5 Manual de usuario
Messoa
Messoa NCB750 Manual de usuario
Messoa
Messoa NDR891(H) Manual de usuario
Messoa
Messoa HCR176 Manual de usuario
Messoa
Messoa NID318 Manual de usuario
Messoa
Messoa SPD970 Manual de usuario
Messoa
Messoa NOD316 Manual de usuario
Messoa
Messoa NDF820 Manual de usuario
Messoa
Messoa SDF418 Manual de usuario
Messoa
Messoa SPD982 Manual de usuario
Messoa
Messoa NDF831-HN5 Manual de usuario
Messoa
Messoa NIC990 Manual de usuario
Messoa
Messoa NCR870 Manual de usuario
Messoa
Messoa NDZ760 Manual de usuario
Messoa
Messoa PTZ900 Manual de usuario
Messoa
Messoa ZEIM-4000604G A.1 Manual de usuario
Messoa
Messoa NDR891 Manual de usuario
