MEI EC6000 Guía del usuario

Part Number 793834002 Rev G2

START- UP GUIDE

EC6000

Change Giver

Page 2 of 9

INSTALLATION

Preparing for Installation

♦Turn OFF all power to the vending machine.

♦To ensure that the EC6000 performance is not

affected, visually check the vending machine is

upright, both from the front and side.

♦Before mounting the EC6000 to the vending

machine, check the operating voltage of the vending

machine matches that stated on the EC6000 label.

Installing the EC6000 to the machine

The EC6000 is mounted onto the vending machine by hanging it onto three studs

located on the vending machine. To do this you will need to open the

discriminator assembly and line up the mounting keyholes of the EC6000 with the

vending machine studs.

♦Press the yellow button at the top of the EC6000 and gently lift and pull the

discriminator assembly forward. Once open, the mounting keyholes will be

made visible.

♦To securely fix the EC6000 in place, partly unscrew the three machine studs.

♦Line up the three mounting keyholes of the EC6000 with the studs and hang it

in place ensuring that the EC6000 is sitting flat against the machine back

plate.

Label

Page 3 of 9

♦Tighten all three studs and return the discriminator back to its normal position.

Alignment Checks

Once the EC6000 has been securely fitted to the vending machine, check reject

lever operation and coin chute alignment. Do this without any power applied to

the machine.

Cable Connection

The EC6000 is available as either MDB or Executive

with looms/cables to integrate MDB peripheral devices

or Audit devices where available.

Once all relevant cables are connected and before

closing the machine door, tuck any unused cables

away tidily ensuring that none are trapped between the

reject lever mechanism and the vending machine door.

You can now switch ON the power to the vending

machine.

Check there is a minimum 4mm gap between

the machines reject lever mechanism and the

EC6000 reject button.

Press the machine lever a couple of times and

ensure the lid of the discriminator opens and

closes correctly.

Check machine coin chute alignment by inserting

two of each coin denomination through the coin

entry slot of the machine.

Ensure that the inserted coins fall freely into the

EC6000 and exit out into the machines cash

return cup.

4mm

Lid

Lever

Reject

Button

Page 4 of 9

KEYPAD FUNCTIONS

On the front of the EC6000 there is a user interface keypad. The keypad has

three LED’s and five function buttons.

This keypad allows you to dispense coins from the four-tube dispenser, access

service mode and monitor the status of the EC6000.

1 3 LED’s Red, Amber, Green

2 to Dispense coins from coin tubes

3 ‘Mode’ Button Access service mode functions

The LED’s provide a visual indication by light flashes that report the state of the

EC6000. An LED can either be ON, OFF or FLASHING. These light flash codes

can indicate when the EC6000 is operating normally, is in service mode or has a

fault. (Refer to the LED light code section for more information)

The blue keys (marked A to D) have two functions.

When the EC6000 is in idle mode, pressing a blue button on its own will dispense

a coin from that tube. When you press and hold the blue button for approx. 4

seconds, this activates auto dispense (latch dispensing of coins) until the tube is

empty of coins. If however, the yellow (mode) button is pressed, the blue buttons

are then used for the EC6000 service mode.

Service Mode: gives access to the most frequently used product configuration

options. (See Service Mode Options - Page 6)

A D

Page 5 of 9

GETTING STARTED

At power up, the EC6000 will run a self test, where the EC6000 motor will sound,

the LED’s will cycle five times through a sequence of red, amber & green.

Floating the Coin Tubes

The EC6000 coin tubes should only be filled by inserting coins through the

discriminator.

Any coins that are manually inserted will not be recognised by the EC6000.

Fill Tube using Service Mode

1. Press the Yellow ‘Mode’ button once.

2. Press ‘A’ button and start inserting coins through the discriminator.

3. Only coins required for the tubes will be accepted and the acceptance will

stop when the set float level is reached.

4. Press the Yellow ‘Mode’ button to exit float mode.

Note: MEI recommends that a small number of coins (e.g. 5 of each) be inserted

in each tube prior to leaving the machine.

Page 6 of 9

Service Mode Options (Quick Menu Codes)

This list shows the most commonly used service modes.

Press Following

Button Sequence Description /

Action

Float coin tubes / (Insert coins through the

discriminator – only tube coins will be accepted)

(When finished press the button)

Clear accumulated credit – (Not MDB)

Inhibit a coin / (Insert a coin and then press the reject

lever and then press the button)

Enable a coin / (Insert a coin and then press the

button)

Teach vend price / (Insert coins to the value of the

price and then press the price line button on the

machine to set it)

(When finished press the button)

Note: After teaching a price the changer is

automatically set into price holding mode.

[This feature is only available on Executive products]

Set to ‘Prices Held in VMC’

‘D’ button must be pressed within 6 seconds of the ‘C’

button.

Warning: This will clear all previously set prices.

[This feature is only available on Executive products]

Token Teach (channel 32) / (Insert 32 tokens through

the discriminator. After the 32nd token is inserted the

EC6000 assignes it as a ‘VEND’ token.

Press the button at any time to Cancel token teach

A A

C D

Page 7 of 9

General LED Light Codes

On - EC6000 OK.

Cycles x 5 - Normal power up sequence.

EC6000 OK.

Blinks Off - Coin accepted / rejected.

Flashing - EC6000 in service mode

On – EC6000 inhibited by VMC.

Flashing - EC6000 requires attention.

(Refer to Amber LED light codes)

Off - No Power to EC6000.

(Check power looms are connected & ensure

power is switched ON)

Alternating - EC6000 Faulty

(Remove from vending machine)

Amber LED Light Codes

If the amber LED flashes, this indicates that a fault has been detected on one of

the EC6000 main modules. These types of fault can be rectified at the machine

and can be for example caused by; a coin jam; dirt built up; or the cassette has

been removed etc. The EC6000 will also indicate the module affected on its

display.

Flashes Check EC6000 Module

1 x Discriminator

2 x Accept gate

3 x Separator module

4 x Dispenser module

Page 8 of 9

Selecting Predefined Cassette

The EC6000 has stored in memory three predefined tube cassettes that provide

different payout options. (See table below).

Cassette Option Tube A Tube B Tube C Tube D

AA 5c 10c 50c 20c

AB 10c 5c 20c 1E

AC - - - -

The cassette payout is automatically detected by the EC6000 when fitted.

If a different cassette payout is detected by the EC6000 it will automatically begin

to calibrate the cassette. For this reason the new cassette variant must be empty

when first installed.

Page 9 of 9

SAFETY

National & International Standards Conformance

EC6000 products operate at Safety Extra Low Voltage Level (SELV) as defined in

IEC335/EN60335 ‘Safety of Household and Similar Appliances’. They may be

designed into equipment complying with IEC335/EN60335 or IEC950/EN60950

‘Safety of Information Technology Equipment’.

EC6000 products are of Class 3 construction.

Rated Operating Voltage

The operating voltage of a EC6000 is stated on the label attached to the product.

It must not be used with any power source other than that indicated.

Dangerous Environments

The EC6000 must not be operated in the presence of flammable gasses, fumes or

water.

Maintenance

If the supply cord is damaged, it must be replaced by the manufacturer, its service

agent or similarly trained persons in order to avoid a hazard.

Access to service areas is restricted to persons with knowledge and training of the

EC6000.

Product Disposal

Do not dispose of any part of a EC6000 by incineration.

EC6000 Start-Up Guide

Revision G2

Publication Date: March 2007

Internet: http://www.meigroup.com

MEI®, and the MEI device are registeredtrademarks.

Numéro de pièce 793834002 Rev G2

GUIDE D'INITIATION RAPIDE

Rendeur de Monnaie

EC6000

Otros manuales para EC6000

Tabla de contenidos

Idiomas:

Otros manuales de Cambiar coche de MEI

MEI

MEI CASHFLOW 7000 Series Guía del usuario

MEI

MEI CashFlow 560 Guía del usuario

Manuales populares de Cambiar coche de otras marcas

American Changer

American Changer AC6007 Manual de usuario

American Changer

American Changer AC2007 Manual de usuario

Coinco

Coinco vortex Instrucciones de funcionamiento originales

American Changer Corp.

American Changer Corp. AC401-2 Guía de configuración

Coinco

Coinco Guardian 6000 Manual de usuario

Comestero

Comestero Suzohapp Multi PRO Manual de usuario

Alberici

Alberici Hira 2 Series Manual de usuario

Coinco

Coinco CoinPro 3 Manual de operación

Hamilton Manufacturing Corporation

Hamilton Manufacturing Corporation DRS Guía de inicio rápido

Alberici

Alberici HammerOne S11 Manual de usuario

Vetus

Vetus IVPS Hoja de especificaciones

Alberici

Alberici Spike CM Arm Manual de usuario

Conlux

Conlux CCM5 series Manual de usuario

American Changer

American Changer AC1001 Guía de configuración

ABACUS

ABACUS AB-1002 Manual de usuario

Alberici

Alberici HIRA ONE Manual de usuario

Suzohapp

Suzohapp Evolution EV01000 Manual de usuario

Alberici

Alberici Hira 2 Midi Manual de usuario