American Changer AC2007 Manual de usuario

AMERICAN CHANGER & HOFFMAN MINT

“We’re Changing The Industry”

1400 N.W. 65th Place Fort Lauderdale, Florida 33309

Tel: 954-917-3009 Fax: 954-917-3079

` www.americanchanger.com www.hoffmanmint.com

Toll Free: 800-741-9840 Toll Free: 800-227-5813

AC2007 Flex System Installation Guide

Step 1: Remove main board, relay board, and power supply.

Step 2: Remove all harnesses inside of the cabinet except for the validator harness, hopper

harnesses, and printer harnesses.

Relay Board

and Main

Board

respectively

Figure 1

Step3: Before mounting the plate with the board and power supply four studs need to be removed.

They can be removed from the cabinet or broken off. The studs are circled in the picture below. The

picture is a view looking at the right wall of the cabinet from the rear of the machine.

Step 4: On the wall the studs were removed from mount the plate with the board and power

supply. It will mount on the two studs closest to the top of the cabinet. Optional adaptor boards

may be mounted on this plate as well.

Figure 2

Figure 3

Step 5: Remove the three nuts that are holding the display in place. See Figure 4. Washers and screw

on stand-offs were supplied with the kit. Add a washer and a screw on stand-off to the studs that

previously had nuts. See Figure 5

Display with

ribbon

harness and

keypad

harness

removed

View from

inside of

machine.

Remove nuts

from Display

Mount.

Figure 4

Display with

the washers

and screw-

on stand offs

installed

Figure 5

Step 6: Attach the I/O Board to the back of the display by inserting the connector on the I/O Board into

the matching connector on the display. Use supplied screws to secure the I/O Board to the stand-offs.

See Figures 6 & 7.

I/O Board

Top View

I/O Board

Bottom View

Figure 6

Figure 7

Connector

Matching

Connector

on Display

Completed

Display with I/O

Board Installed

Step 7: Connect your heater in to “#2” on the power board.

Harness to the

main board

Heater

Figure 8

Step 8: If you will be connecting your machine to your local network please proceed to the next step.

Drill a hole in the top of the cabinet to mount the antenna using a 5/8th inch steel hole saw. Mount the

antenna and run the harness through the hole into the machine.

Marquee with

hole for

antenna

Marquee with

antenna

mounted

Figure 9

Step 9: Connect the antenna or Ethernet cable to the Iris device.

Front of Iris device.

Connect Ethernet

cable here

Rear of Iris device.

Connect antenna

cable here

Figure 10

Step 10:Use the below picture to help with connecting the components to the main board.

Printer

I/O

Board

Tran

Unit

Figure 10

Additional steps for connecting optional adaptor boards

This section details how to connect adaptor boards to the main board. Adaptor boards are not shipped

with all orders. These boards will already have the necessary harnesses attached to them. All that will

be needed is to connect the component to the adaptor board. If you did not receive any adaptor boards

with your order then skip this section.

Step 11: Connect the hopper plate harness to the hopper adaptor board. Then connect the harness

that was already attached to the adaptor board to the main board.

Step 12: Connect the flat “ribbon” style harness from your printer to the adaptor board. Then do the

same for the power harness. Again connect the harness that is already attached to the adaptor board to

the main board.

Connect hopper plate

here.

Harness to main board

connects here.

Connect power harness

here.

Harness to main board

connects here.

Connect ribbon harness

here.

Figure 11

Figure 12

Installing the External Keypad

The following steps are used to install the external keypad that came with the kit. This keypad is used to

navigate the programming menu as well as input values while in the programming menu. The external

keypad can also be used to input a zip code if zip code verification is enabled. American Changer

recommends having a professional drill the holes in the stainless steel face plate.

Step 1: It is recommended to mount the keypad next to the display. Place the keypad against the face

plate and use a felt tip marker to mark your four mounting holes. You will also need to mark the area

for the harness to connect to the key pad.

Front View

Four Mounting Holes

Rear View

Connector for

Harness

Figure 13

Otros manuales de Cambiar coche de American Changer

American Changer

American Changer AC6007 Manual de usuario

American Changer

American Changer AC1001 Guía de configuración

Manuales populares de Cambiar coche de otras marcas

Coinco

Coinco vortex Instrucciones de funcionamiento originales

American Changer Corp.

American Changer Corp. AC401-2 Guía de configuración

Coinco

Coinco Guardian 6000 Manual de usuario

Comestero

Comestero Suzohapp Multi PRO Manual de usuario

Alberici

Alberici Hira 2 Series Manual de usuario

Coinco

Coinco CoinPro 3 Manual de operación

Hamilton Manufacturing Corporation

Hamilton Manufacturing Corporation DRS Guía de inicio rápido

Alberici

Alberici HammerOne S11 Manual de usuario

Vetus

Vetus IVPS Hoja de especificaciones

Alberici

Alberici Spike CM Arm Manual de usuario

MEI

MEI EC6000 Guía del usuario

Conlux

Conlux CCM5 series Manual de usuario

MEI

MEI CashFlow 560 Guía del usuario

MEI

MEI CASHFLOW 7000 Series Guía del usuario

ABACUS

ABACUS AB-1002 Manual de usuario

Alberici

Alberici HIRA ONE Manual de usuario

Suzohapp

Suzohapp Evolution EV01000 Manual de usuario

Alberici

Alberici Hira 2 Midi Manual de usuario