Meech Hyperion 960IPS Manual de usuario
Hyperion 971IPS
Long-Range DC Bar
Operating Manual
Hyperion 960IPS
Mid-Range DC Bar
v1.02
Products shown in this document may be covered by one or more patents, patents applied for
and/or registered designs and/or trade marks. For further information please refer to our Head
Oce or visit www.meech.com.
© Meech Static Eliminators Ltd., 01.07.2020
Contents
Introduction 3
Unpacking and Inspection 4
Contents 4
Options 4
Features and Benets of Hyperion 960IPS 5
Installation 8
Operation 17
Maintenance 17
Fault Finding 18
Troubleshooting 21
Repairs and Warranty 22
Technical and Construction 23
CE Approval 23
Health and Safety 24
Technical Drawing 24
Declaration of Conformity 25
3
Introduction
The Hyperion 960 IPS is a powerful, compact pulsed DC ionising bar. It is used
to control static electric charges in short to mid-range applications (150-600mm).
An integral 15kV pulsed DC power supply allows for easy installation on printing,
converting and packaging machinery. Requiring only a 24V DC supply, the 960 IPS
removes the need to route high-voltage cabling through the machine.
In most installations the default settings of the bar will provide exceptional static
control. The local LED indicator shows the operational status of the bar and advises
when the bar requires cleaning.
Demanding installations can take advantage of the adjustable output of the 960 IPS.
Using the optional Hyperion BarMaster remote programmer or SmartControl (each
sold separately), the frequency, balance and voltage can be optimised to suit the
application. Additionally, the lon Current alarm setting can be changed to guarantee
the required performance levels on critical processes, and dual alarm lines enable
remote monitoring for system maintenance and faults.
The Hyperion BarMaster remote programmer and SmartControl are available for
purchase from the Meech network: Visit www.meech.com to nd your nearest Meech
oce or distributor for further product information.
4
Unpacking And Inspection
Your Hyperion 960IPS bar was carefully packed at the factory in a container
designed to protect it from accidental damage. Nevertheless, we recommend careful
examination of the carton and contents for any damage.
If damage is evident, do not destroy the carton or packing material and immediately
notify the carrier of a possible damage claim. Shipping claims must be made by the
consignee to the delivering carrier.
Contents:
Standard
960IPS Bar Mounting Kit
Options
Power Cable - 4 Pin M8
(straight or 90º elbow)
Available in 2,3,5 and
10M lengths.
24V DC Supply & IEC
cable
BarMaster remote
programmer.
Allows optimisation of
the output of the 960
IPS
5
Features and Benets of Hyperion 960IPS
Low voltage wiring and Integrated Power Supply
The 960IPS is powered by 24V DC via a 4-pin M8 Connector.
Shockless Emitters
The Titanium emitter pins on the 960IPS are resistively coupled to the high voltage
supply. This avoids sparking and operator shocks.
Sealed Construction
IP66 construction allows the bar to be mounted in areas subject to occasional wash-
down or spillage. If the bar does become wet it must be thoroughly dried before being
powered-up.
Clean Pin Alert and Fault LED
The local LED illuminates green to indicate that the bar is on and working correctly.
Red ashing LED shows that bar is dirty and needs cleaning. Solid red illumination
indicates a fault with the high voltage output.
Green - OK
Green ashing - Barmaster remote programmer connected
Red ashing - Cleaning required
Red constant - Fault
Dual Alarm Lines - Clean Pin Alert and Fault Alert
Output
Dual alarm lines tell remote monitoring systems whether the ionising equipment needs
routine maintenance or whether there is a more serious system failure. The exible
conguration of the alarm system, allows the alarm lines to be interfaced with PLC’s,
buzzers and remote lamps.
Dual output signals indicate when the bar needs cleaning and when a fault has been
detected. The signal is 0V/24V output on pin 2 for Clean Pin Output and 0V/24V
output on pin 4 for Fault Alert Output. The default for Bar OK = 24V and for Bar needs
cleaning = 0V. For the Fault Alert Output the default is 0V. If required the signal can be
inverted using a BarMaster Remote Programmer or SmartControl. For example Bar
OK = 0V, Cleaning Required = 24V.
6
7
Divider
The 960IPS is designed to operate in dirty, factory environments. To maximise the
interval between cleaning, the bar features a divider to increase the surface tracking
distance between the two rows of high voltage pins. It is important to clean this area
during cleaning operations.
T-Slot
The bar is mounted using the T-Slot at the rear of the bar. M4 T-bolts supplied with the
bar can be positioned to suit convenient mounting points.
8
Installation
Mechanical Installation
The 960 is a short to mid-range bar. Dependent on the application, the bar will be
mounted between 150mm and 600mm from the target surface.
The bar should be mounted securely, using all the M4 T-bolts provided with the bar.
Correct positioning of the bar is vital for eective static control. There must be no
metallic objects or obstruction between the bar and the material. The diagram shows
the area that should be kept clear.
Where xlengths are equal.
Tabla de contenidos
Otros manuales de Barra de iones de Meech
Meech
Meech 976 Manual de usuario
Meech
Meech 915EX Manual de usuario
Meech
Meech Hyperion 314IPS Manual de usuario
Meech
Meech 976EX Manual de usuario
Meech
Meech 924EX Manual de usuario
Meech
Meech 914EX Manual de usuario
Meech
Meech 910 Manual de usuario
Meech
Meech Hyperion 929IPS Manual de usuario
Meech
Meech 914 Manual de usuario
Meech
Meech 971 Manual de usuario
