Meech Hyperion 924IPS Manual de usuario
Hyperion 971IPS
Long-Range DC Bar
Operating Manual
Hyperion 924IPS
Short-Range DC Bar
Products shown in this document may be covered by one or more patents, patents applied for
and/or registered designs and/or trade marks. For further information please refer to our Head
Ofce or visit www.meech.com.
© Meech Static Eliminators Ltd., 18.02.2016
Contents
Introduction 3
Unpacking and Inspection 4
Contents 4
Options 4
Features of Hyperion 924IPS 5
Installation 8
Operation 12
Maintenance 13
Troubleshooting 15
Technical Characteristics 16
CE Approval 16
Health and Safety 16
Repairs and Warranty 17
Technical Drawing 17
3
Introduction
The Hyperion 924 IPS is a compact pulsed DC ionising bar. It is used to control static
electric charges in short range applications (20-150mm). An integral 7.5kV pulsed DC
power supply allows for easy installation on printing,
converting and packaging machinery. Requiring only a 24V DC supply, the 924 IPS
removes the need to route high-voltage cabling through the machine.
In most installations the default settings of the bar will provide exceptional static
control. The local LED indicator shows the operational status of the bar and advises
when the bar requires cleaning.
Demanding installations can take advantage of the adjustable output of the 924 IPS.
Using the optional Hyperion BarMaster remote programmer, the frequency, balance
and voltage output can be optimised to suit the application. Additionally, the lon
Current alarm setting can be changed to guarantee the required performance levels
on critical processes.
The Hyperion BarMaster remote programmer is available for purchase from the Meech
network: Visit www.meech.com to nd your nearest Meech ofce or distributor for
further product information.
4
Unpacking And Inspection
Your Hyperion 924IPS bar was carefully packed at the factory in a container
designed to protect it from accidental damage. Nevertheless, we recommend careful
examination of the carton and contents for any damage.
If damage is evident, do not destroy the carton or packing material and immediately
notify the carrier of a possible damage claim. Shipping claims must be made by the
consignee to the delivering carrier.
Contents:
Standard
924IPS Bar Mounting Kit
Options
Power Cable - 4 Pin M8
(straight or 90º elbow)
Available in 2,3,5 and
10M lengths.
24V DC Supply & IEC
cable
BarMaster remote
programmer.
Allows optimisation
of the output of the
924IPS
5
Features and Benets of Hyperion 924IPS
Low voltage wiring and Integrated Power Supply
The 924IPS is powered by 24V DC via a 4-pin M8 Connector.
Shockless Emitters
The Titanium emitter pins on the 924IPS are resistively coupled to the high voltage
supply. This avoids sparking and operator shocks.
Sealed Construction
IP66 construction allows the bar to be mounted in areas subject to occasional wash-
down or spillage. If the bar does become wet it must be thoroughly dried before being
powered-up.
6
Clean Pin Alert LED
The local LED ashes constant green to indicate that the bar is on and working
correctly. Red ashing LED shows that bar is dirty and needs cleaning. Solid red
illumination indicates a fault with the high voltage output.
Green constant – OK
Green ashing – BarMaster remote programmer connected
Red ashing - Cleaning required
Red constant - Fault
Clean Pin Alert and Fault Output
An output signal indicates when the bar needs cleaning or when a fault has been
detected. The signal is 0V/24V output on pin 2. By default: Bar OK = 24V, Bar needs
cleaning (or fault detected) = 0V. If required the signal can be inverted to give OK =
0V, Cleaning Required = 24V using a Barmaster Remote Programmer
7
Divider
The 924IPS is designed to operate in dirty, factory environments. To maximise the
interval between cleaning the bar features a divider to increase the surface tracking
distance between the two rows of high voltage pins. It is important to clean this area
during cleaning operations.
T-Slot
The bar is mounted using the T-Slot at the rear of the bar. M4 T-bolts supplied with the
bar maybe positioned to suit convenient mounting points.
8
Installation
Mechanical Installation
The 924 is a short to mid-range bar. Dependent on the application, the bar will be
mounted between 20mm and 150mm from the target surface.
The bar should be mounted securely, using all the M4 T-bolts provided with the bar.
Correct positioning of the bar is vital for effective static control. There must be no
metallic objects or obstruction between the bar and the material. The diagram shows
the area that should be kept clear.
Where xlengths are equal.
Tabla de contenidos
Otros manuales de Barra de iones de Meech
Meech
Meech 914EX Manual de usuario
Meech
Meech 915 Manual de usuario
Meech
Meech 914 Manual de usuario
Meech
Meech 976EX Manual de usuario
Meech
Meech 924EX Manual de usuario
Meech
Meech Hyperion 960IPS Manual de usuario
Meech
Meech 910 Manual de usuario
Meech
Meech Hyperion 929IPS Manual de usuario
Meech
Meech 976 Manual de usuario
Meech
Meech 971 Manual de usuario
