Maxtor 51536H2 Manual de usuario

Hard Disk Drive Specifications

Models:546106,53073H4,

52049H3,51536H2

This publication could include technical inaccuracies or typographical

errors. Changes are periodically made to the information herein – which

will be incorporated in revised editions of the publication. Maxtor may

make changes or improvements in the product(s) described in this

publication at any time and without notice.

MaxFax®and No Quibble Service®are registered trademarks of Maxtor

Corporation. Other brands or products are trademarks or registered

trademarks of their respective holders.

Corporate Headquarters

510 Cottonwood Drive

Milpitas, California 95035

Tel: 408-432-1700

Fax: 408-432-4510

Research and Development Center

2190 Miller Drive

Longmont, Colorado 80501

Tel: 303-651-6000

Fax: 303-678-2165

P/N:1493/A

Revisions Manual No. 1493

REV EC NO. SECTION DESCRIPTION DATE

A 80345 All Initial release. 7/19/2000

BeforeYBeforeY

BeforeYouBeginouBegin

ouBeginouBegin

ouBegin

Thank you for your interest in Maxtor hard disk drives. This manual provides technical information for OEM

engineers and systems integrators regarding the installation and use of Maxtor hard drives. Drive repair should be

performed only at an authorized repair center. For repair information, contact the Maxtor Customer Service Center

at 800-2MAXTOR or 408-922-2085.

Before unpacking the hard drive, please review Sections 1 through 4.

CAUTION

Maxtor hard drives are precision products. Failure to follow these precautions

and guidelines outlined here may lead to product failure, damage

and invalidation of all warranties.

1BEFORE unpacking or handling a drive, take all proper electro-static discharge (ESD)

precautions, including personnel and equipment grounding. Stand-alone drives are

sensitive to ESD damage.

BEFORE

removing drives from their packing material, allow them to reach room

temperature.

3During handling,

NEVER

drop, jar, or bump a drive.

4Once a drive is removed from the Maxtor shipping container,

IMMEDIATELY

secure

the drive through its mounting holes within a chassis. Otherwise, store the drive on a

padded, grounded, antistatic surface.

NEVER

switch DC power onto the drive by plugging an electrically live DC source cable

into the drive's connector.

NEVER

connect a live bus to the drive's interface connector.

ELECTRICAL GROUNDING -

For proper operation, the drive must be securely fastened

to a device bay that provides a suitable electrical ground to the drive baseplate.

Please do not remove or cover up Maxtor factory-installed drive labels.

They contain information required should the drive ever need repair.

ContentsContents

Contents

Section 1Section 1

Section 1— IntroductionIntroduction

IntroductionIntroduction

Introduction

Maxtor Corporation 1 - 1

Products 1 - 1

Support 1 - 1

Manual Organization 1 - 1

Abbreviations 1 - 1

Conventions 1 - 2

Key Words 1 - 2

Numbering 1 - 2

Signal Conventions 1 - 2

Section 2Section 2

Section 2 —Product DescriptionProduct Description

Product DescriptionProduct Description

Product Description

Product Features 2 - 2

Functional/Interface 2 - 2

Zone Density Recording 2 - 2

Read/Write Multiple Mode 2 - 2

Ultra ATA - Mode 5 2 - 2

Multi-word DMA (EISA Type B) - Mode 2 2 - 2

Sector Address Translation 2 - 2

Logical Block Addressing 2 - 3

Defect Management Zone 2 - 3

On-the-Fly Hardware Error Correction Code (ECC) 2 - 3

Software ECC Correction 2 - 3

Automatic Head Park and Lock Operation 2 - 3

Cache Management 2 - 4

Buffer Segmentation 2 - 4

Read-Ahead Mode 2 - 4

Automatic Write Reallocation (AWR) 2 - 4

Write Cache Stacking 2 - 4

Major HDA Components 2 - 5

Drive Mechanism 2 - 5

Rotary Actuator 2 - 5

Read/Write Electronics 2 - 5

Read/Write Heads and Media 2 - 5

Air Filtration System 2 - 5

Microprocessor 2 - 5

Subsystem Configuration 2 - 6

Dual Drive Support 2 - 6

Cable Select Option 2 - 6

Jumper Location/Configuration 2 - 6

Cylinder Limitation 2 - 6

Section 3Section 3

Section 3 —Product SpecificationsProductSpecifications

Product SpecificationsProduct Specifications

Product Specifications

Models and Capacities 3 - 1

Drive Configuration 3 - 1

Performance Specifications 3 - 1

Physical Dimensions 3 - 2

Power Requirements 3 - 3

Power Mode Definitions 3 - 3

Spin-up 3 - 3

Seek 3 - 3

Read/Write 3 - 3

Idle 3 - 3

Standby 3 - 3

Sleep 3 - 3

EPA Energy Star Compliance 3 - 3

Environmental Limits 3 - 3

Shock and Vibration 3 - 4

Reliability Specifications 3 - 4

Annual Return Rate 3 - 4

Quality Acceptance Rate 3 - 4

Start/Stop Cycles 3 - 4

Data Reliability 3 - 4

Component Design Life 3 - 4

EMC/EMI 3 - 5

EMC Compliance 3 - 5

Canadian Emissions Statement 3 - 5

Safety Regulatory Compliance 3 - 5

Section 4Section 4

Section 4—Handling and InstallationHandling and Installation

Handling and InstallationHandling and Installation

Handling and Installation

Hard Drive Handling Precautions 4 - 1

Electro-Static Discharge (ESD) 4 - 1

Unpacking and Inspection 4 - 2

Repacking 4 - 3

Physical Installation 4 - 3

Before You Begin 4 - 4

Please Read 4 - 4

Back up. Protect Your Existing Data 4 - 4

Tools for Installation 4 - 4

System Requirements 4 - 4

Operating System Requirements 4 - 4

Hook up 4 - 4

Boot the System with MaxBlast Plus Diskette 4 - 4

Configure the Drive Jumpers 4 - 4

Installaing 5.25-inch Mounting Brackets 4 - 4

Install Hard Drive in Device Bay 4 - 5

Attach Interface and Power Cables 4 - 5

Start up 4 - 5

Set up 4 - 5

iii

Section 5Section 5

Section 5— AT Interface DescriptionAT Interface Description

AT Interface DescriptionAT Interface Description

AT Interface Description

Interface Connector 5 - 1

Pin Description Summary 5 - 1

Pin Description Table 5 - 2

PIO Timing 5 - 3

DMA Timing 5 - 4

Ultra DMA Timing Parameters 5 - 5

Section 6Section 6

Section 6— Host Software InterfaceHost Software Interface

Host Software InterfaceHost Software Interface

Host Software Interface

Task File Registers 6 - 1

Data Register 6 - 1

Error Register 6 - 1

Features Register 6 - 1

Sector Count Register 6 - 2

Sector Number Register 6 - 2

Cylinder Number Registers 6 - 2

Device/Head Register 6 - 2

Status Register 6 - 2

Command Register 6 - 3

Read Commands 6 - 3

Write Commands 6 - 3

Mode Set/Check Commands 6 - 3

Power Mode Commands 6 - 3

Initialization Commands 6 - 3

Seek, Format, and Diagnostic Commands 6 - 3

S.M.A.R.T. Commands 6 - 3

Summary 6 - 4

Control Diagnostic Registers 6 - 5

Alternate Status Register 6 - 5

Device Control Register 6 - 5

Digital Input Register 6 - 5

Reset and Interrupt Handling 6 - 6

Section7Section7

Section7—Interface CommandsInterfaceCommands

Interface CommandsInterface Commands

Interface Commands

Command Summary 7 - 1

Read Commands 7 - 2

Read Sector(s) 7 - 2

Read Verify Sector(s) 7 - 2

Read Sector Buffer 7 - 2

Read DMA 7 - 3

Read Multiple 7 - 3

Set Multiple 7 - 3

Write Commands 7 - 4

Write Sector(s) 7 - 4

Write Verify Sector(s) 7 - 4

Write Sector Buffer 7 - 4

Write DMA 7 - 5

Write Multiple 7 - 5

Mode Set/Check Commands 7 - 6

Set Features Mode 7 - 6

Read Native Max Address 7 - 7

Set Max 7 - 7

Set Max Password 7 - 7

Set Max Lock 7 - 7

Set Max Unlock 7 - 7

Set Max Freeze Lock 7 - 7

Power Mode Commands 7 - 8

Standby Immediate 7 - 8

Idle Immediate 7 - 8

Standby 7 - 8

Idle 7 - 8

Check Power Mode 7 - 8

Set Sleep Mode 7 - 8

Default Power-on Condition 7 - 9

Initialization Commands 7 - 10

Identify Drive 7 - 10

Initialize Drive Parameters 7 - 13

Seek, Format, and Diagnostic Commands 7 - 14

S.M.A.R.T. Command Set 7 - 15

Section 8Section 8

Section 8— Service and SupportService and Support

Service and SupportService and Support

Service and Support

Service Policy 8 - 1

No Quibble Service 8 - 1

Support 8 - 1

GlossaryGlossary

Glossary

FiguresFigures

Figures

Figure Title Page

2 - 1 PCBA Jumper Location and Configuration 2 - 6

3 - 1 Outline and Mounting Dimensions 3 - 2

4 - 1 Multi-pack Shipping Container 4 - 2

4 - 2 Single-pack Shipping Container (Option A) 4 - 3

4 - 3 Single-pack Shipping Container (Option B) 4 - 3

4 - 4 IDE Interface and Power Cabling Detail 4 - 5

5 - 1 Data Connector 5 - 1

5 - 2 PIO Data Transfer to/from Device 5 - 3

5 - 3 Multi-word DMA Data Transfer 5 - 4

5 - 4 Initiating an Ultra DMA Data In Burst 5 - 5

5 - 5 Sustained Ultra DMA Data In Burst 5 - 6

5 - 6 Host Pausing an Ultra DMA Data In Burst 5 - 6

5 - 7 Device Terminating an Ultra DMA Data In Burst 5 - 7

5 - 8 Host Terminating an Ultra DMA Data In Burst 5 - 7

5 - 9 Initiating an Ultra DMA Data Out Burst 5 - 8

5 - 10 Sustained Ultra DMA Data Out Burst 5 - 8

5 - 11 Device Pausing an Ultra DMA Data Out Burst 5 - 9

5 - 12 Host Terminating an Ultra DMA Data Out Burst 5 - 9

5 - 13 Device Terminating an Ultra DMA Data Out Burst 5 - 10

INTRODUCTION

1 – 1

SECTION 1

IntroductionIntroduction

Introduction

MaxtorCorporationMaxtorCorporation

MaxtorCorporation

Maxtor Corporation has been providing high-quality computer storage products since 1982. Along the way,

we’ve seen many changes in data storage needs. Not long ago, only a handful of specific users needed more than

a couple hundred megabytes of storage. Today, downloading from the Internet and CD-ROMs, multimedia,

networking and advanced office applications are driving storage needs even higher. Even home PC applications

need capacities measured in gigabytes, not megabytes.

ProductsProducts

Products

Maxtor’s products meet the demanding data storage capacity requirements of today and tomorrow. They are

available in 5400- and 7200- RPM configurations with capacity offerings from 10 to 80 GB and beyond.

SupportSupport

Support

No matter which capacity, all Maxtor hard drives are supported by our commitment to total customer

satisfaction and our No Quibble Service®guarantee. One call – or a visit to our home page on the Internet

(www.maxtor.com) – puts you in touch with either technical support or customer service. We’ll provide

you the information you need quickly, accurately and in the form you prefer – a fax, a downloaded file or

a conversation with a representative.

ManualOrganizationManualOrganization

ManualOrganization

This hard disk drive reference manual is organized in the following method:

Section 1 – Introduction

Section 2 – Product Description

Section 3 – Product Specifications

Section 4 – Handling and Installation

Section 5 – AT Interface Description

Section 6 – Host Software Interface

Section 7 – Interface Commands

Section 8 – Service and Support

Appendix – Glossary

AbbreviationsAbbreviations

Abbreviations

ABBRV DESCRIPTION ABBRV DESCRIPTION

ATA AT attachment MB megabyte

bpi bits per inch Mbits/sec megabits per second

CHS cylinder - head - sector MB/sec megabytes per second

db decibels MHz megahertz

dBA decibels, A weighted ms millisecond

DMA direct memory access MSB most significant bit

ECC error correction code mV millivolts

fci flux changes per inch ns nanoseconds

G acceleration PIO programmed input/output

GB gigabyte RPM revolutions per minute

Hz hertz tpi tracks per inch

KB kilobyte UDMA ultra direct memory access

LBA logical block address(ing) µsec microsecond

LSB least significant bit V volts

mA milliamperes W watts

INTRODUCTION

1 – 2

ConventionsConventions

Conventions

If there is a conflict between text and tables, the table shall be accepted as being correct.

Key WordsKey Words

Key Words

The names of abbreviations, commands, fields and acronyms used as signal names are in all uppercase type

(e.g., IDENTIFY DRIVE). Fields containing only one bit are usually referred to as the “name” bit instead of

the “name” field.

Names of drive registers begin with a capital letter (e.g., Cylinder High register).

NumberingNumbering

Numbering

Numbers that are not followed by a lowercase “b” or “h” are decimal values. Numbers that are followed by

a lowercase “b” (e.g., 01b) are binary values. Numbers that are followed by a lowercase “h” (e.g., 3Ah) are

hexadecimal values.

Signal ConventionsSignal Conventions

Signal Conventions

Signal names are shown in all uppercase type.

All signals are either high active or low active signals. A dash character (-) at the end of a signal name

indicates that the signal is low active. A low active signal is true when it is below ViL and is false when it is

above ViH. A signal without a dash at the end indicates that the signal is high active. A high active signal is

true when it is above ViH and is false when it is below ViL.

When a signal is asserted, it means the signal is driven by an active circuit to its true state.

When a signal is negated, it means the signal is driven by an active circuit to its false state.

When a signal is released, it means the signal is not actively driven to any state. Some signals have bias

circuitry that pull the signal to either a true or false state when no signal driver is actively asserting or negating

the signal. These instances are noted under the description of the signal.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Almacenamiento de Maxtor

Maxtor

Maxtor OneTouch II E01V200 Manual de usuario

Maxtor

Maxtor Personal Storage 3000LE Manual de usuario

Maxtor

Maxtor STM3160215AS Manual de usuario

Maxtor

Maxtor SERIAL ATA HARD DRIVE Manual de usuario

Maxtor

Maxtor 2B020H1 Manual de usuario

Maxtor

Maxtor Personal Storage 5000DV Manual de usuario

Maxtor

Maxtor Basics ATA/100 Manual de usuario

Maxtor

Maxtor Maxtor OneTouch USB Manual de usuario

Maxtor

Maxtor Maxtor Manual de usuario

Maxtor

Maxtor HDD Manual de usuario

Maxtor

Maxtor Maxtor OneTouch 4 Manual de usuario

Maxtor

Maxtor BlackArmor Manual de usuario

Maxtor

Maxtor Basics 120GB STM901203EHM301-RK Manual de usuario

Maxtor

Maxtor Personal Storage 5000DV Manual de usuario

Maxtor

Maxtor Personal Storage 3000DV Manual de usuario

Maxtor

Maxtor Maxtor Basics Desktop Manual de usuario

Maxtor

Maxtor Maxtor OneTouch FireWire Manual de usuario

Maxtor

Maxtor Personal Storage 3000LE Manual de usuario

Maxtor

Maxtor MaXLine III Manual de usuario

Maxtor

Maxtor Personal Storage 5000DV Manual de instrucciones

Maxtor

Maxtor BlackArmor Manual de usuario

Maxtor

Maxtor DiamondMax 20 Serial ATA Manual de usuario

Maxtor

Maxtor OneTouch II Manual de usuario

Maxtor

Maxtor DIAMONDMAX VL20 92041U4 Manual de usuario

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

HP StorageWorks MSL2024 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

HP P9000 Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario