MATSONIC MS7308E Series Manual de usuario
Mainboard User’s Manual
This publication, including all photographs, illustrations and
software, is protected under international copyright laws, with all
rights reserved. Neither this manual, nor any of the material
contained herein, may be reproduced without the express written
consent of the manufacturer.
The information in this document is subject to change without
notice. The manufacturer makes no representations or warranties
with respect to the contents hereof and specifically disclaims any
implied warranties of merchantability or fitness for any particular
purpose. Further, the manufacturer reserves the right to revise this
publication and to make changes from time to time in the content
hereof without obligation of the manufacturer to notify any person
of such revision or changes.
Trademarks
IBM, VGA, and PS/2 are registered trademarks of International
Business Machines.
Intel, Pentium, Pentium-II, Pentium-III, MMX, and Celeron are
registered trademarks of Intel Corporation.
Microsoft, MS-DOS and Windows 95/98/NT are registered
trademarks of Microsoft Corporation.
Sound Blaster is a trademark of Creative Technology Ltd.
PC-cillin and ChipAwayVirus are trademarks of Trend Micro Inc.
AMI is a trademark of American Megatrends Inc.
A3D is a registered trademark of Aureal Inc.
Gamut is a registered trademark of Formosoft International Inc.
SuperVoice is a registered trademark of Pacific Image
Communications Inc.
MediaRing Talk is a registered trademark of MediaRing Inc.
Other names used in this publication may be trademarks and are
acknowledged.
Copyright © 2000
All Rights Reserved
MS7308D/E, V1.6
S63X/JUNE 2000
MS7308D/EMainboard User’s Manual
II
Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
qReorient or relocate the receiving antenna.
qIncrease the separation between the equipment and the receiver.
qConnect the equipment onto an outlet on a circuit different from that
to which the receiver is connected.
qConsult the dealer or an experienced radio/TV technician for help.
Shielded interconnect cables and shielded AC power cable must be
employed with this equipment to insure compliance with the pertinent RF
emission limits governing this device. Changes or modifications not
expressly approved by the system’s manufacturer could void the user’s
authority to operate the equipment.
Declaration of Conformity
This device complies with part 15 of the FCC rules. Operation is subject
to the following conditions:
qThis device may not cause harmful interference, and
qThis device must accept any interference received, including
interference that may cause undesired operation.
Canadian Department of Communications
This class B digital apparatus meets all requirements of the Canadian
Interference-causing Equipment Regulations.
Cet appareilnumérique de la classeB respecte toutes les exigences du
Réglement sur le matériel brouilieur du Canada.
MS7308E Mainboard User’s Manual
III
Table of Contents
Chapter 1: Introduction..............................................................1
Key Features......................................................................2
Package Contents...............................................................5
Static Electricity Precautions...............................................6
Pre-Installation Inspection...................................................6
Chapter 2: Mainboard Installation...............................................7
Mainboard Components......................................................8
Install A CPU ....................................................................9
Install Memory.................................................................10
Setting Jumper Switches...................................................11
Install the Mainboard........................................................13
Optional Extension Brackets.............................................14
Install Other Devices........................................................15
Expansion Slots................................................................17
Chapter 3: BIOS Setup Utility..................................................19
Introduction.....................................................................19
Running the Setup Utility..................................................20
Standard CMOS Setup Page .............................................21
Advanced Setup Page.......................................................22
Power Management Setup Page ........................................24
PCI / Plug and Play Setup Page.........................................26
Load Optimal Settings ......................................................27
Load Best Performance Settings ........................................27
Features Setup Page .........................................................28
CPU PnP Setup Page........................................................30
Hardware Monitor Page....................................................31
Change Password.............................................................31
Exit..................................................................................32
Chapter 4: Software & Applications..........................................33
About the Software ..........................................................33
Folders for this Mainboard................................................33
Running the Support CD-ROM.........................................34
Utility Folder Installation Notes ........................................34
Mainboard (MS7308D/E) Installation Notes ......................35
MS7308D/EMainboard User’s Manual
IV
Appendix A: Gamut .............................................................A1
Introduction ....................................................................A2
Before Installing .............................................................A3
Installation .....................................................................A4
Produce MP3 fileUse CD-Cashier ................................A5
Play MP3 fileUse Musician .........................................A7
Play music CDUse 3DFS-ACD .....................................A8
Play MIDI fileUse Midier ............................................A9
Recording audio dataUse Voice-Catcher ....................A10
1: Introduction
1
Chapter 1
Introduction
This mainboard has a Socket 370, which uses either an Intel
PPGA (Plastic Pin Grid Array) Celeron or FCPGA Pentium III
processor.
This mainboard supports front-side bus speeds of 66MHz,
100MHz or 133MHz.
This mainboard uses the SiS 630 chipset which provides CPU
Plug & Play through firmware, integrates a 128-bit AGP
Graphics Accelerator and has an embedded
10BaseT/100BaseTX Network Interface. The mainboard has a
built-in PCI 3D Sound System. There is an AMR slot for the
AMR device cards .In addition, the mainboard has a full set of
ATX I/O Ports including PS/2 keyboard and mouse ports, two
USB ports, a parallel port, a serial port and a VGA port. And three
extra USB ports can be added using the Extended USB Module
that connects to the mainboard.
This mainboard has all the features you need to develop a powerful
multimedia workstation that is network ready, and has built-in
communications. The board is Micro-ATX size and has power
connector for an ATX power supply.
MS7308D/EMainboard User’s Manual
2
Key Features
The key features of this mainboard include:
Socket-370 Processor Support
♦Supports PPGA Celerons from 300MHz to 600MHz.
♦FCPGA Pentium III CPUs are supported
♦Supports 66MHz, 100MHz or 133MHz FSB
All processors are automatically configured using firmware and a
synchronous/asynchronous Host/DRAM Clock Scheme.
Memory Support
♦Two DIMM slots for 168-pin SDRAM memory modules
♦Support for 66MHz, 100MHz, & 133MHz memory bus
♦Maximum installed memory is 2 x 512MB = 1 GB
Expansion Slots
♦Two 32-bit PCI slots
♦One AMR slot for a special audio/modem riser card
Onboard IDE channels
♦Primary and Secondary PCI IDE channels
♦Support for PIO (programmable input/output) modes
♦Support for Multiword DMA modes
♦Support for Bus Mastering and Ultra DMA 33/66 modes
Power Supply and Power Management
♦ATX power supply connector
♦ACPI and previous PMU support, suspend switch,
keyboard power on/off
♦Supports Wake on Modem, Wake on LAN and Wake on
Alarm
1: Introduction
3
Built-in Graphics System
♦Onboard 128-bit 2D/3D 100MHz Host interface AGP
Graphics Accelerator Complies with AGP 1x,2x,4x
♦Shared memory architecture allows a maximum of 64 MB
main memory to act as frame buffer
♦Supports high resolutions up to 1920x1200 16M colors, up
to 2048x2048 Texture size and Virtual screen up to
4096x4096
♦Supports hardware DVD Accelerator
Sound System
♦Complies with the PC99 audio specification
♦16-bit CODEC for full-duplex playback and recording
♦Driver support for Windows 95/98/2000/NT 4.0
♦Provides MPU-401 Game/MIDI port and legacy Sound
Blaster 16 support
♦Downloadable Wave-table Synthesizer supports Direct
Music®
♦48KHz sampling rate and measured 90dB audio quality
Onboard I/O Ports
♦Provides PC99 Color Connectors for easy peripheral device
connections
♦Floppy disk drive connector with 1Mb/s transfer rate
♦One serial port with 16550-compatible fast UART
♦One parallel port with ECP and EPP support
♦Five USB ports (three for optional) and two PS/2 ports for
keyboard and mouse
♦One infrared port connector for optional module
Built-in Ethernet LAN
♦Optional 10BaseT/100BaseTX Ethernet LAN
♦LAN controller integrates Fast Ethernet MAC and PHY
compliant with IEEE802.3u 100BASE-TX, 10BASE-T and
ANSI X3.263 TP-PMD standards
♦Compliant with ACPI 1.0 and the Network Device Class
Power Management 1.0
MS7308D/EMainboard User’s Manual
4
♦High Performance provided by 100Mbps clock generator and
data recovery circuit for 100Mbps receiver
Onboard Flash ROM
♦Automatic CPU and board configuration
♦Supports Plug and Play configuration of peripheral devices
and expansion cards
♦Built-in virus protection using Trend’s ChipAwayVirus
provides boot process virus protection.
Bundled Software
♦PC-Cillin provides automatic virus protection under DOS,
Windows 95/98
♦SuperVoice is data, fax and voice communication software
♦Gamut provides professional audio features included MP3
encoding/playback
♦MediaRing Talk provides PC to PC or PC to Phone
internet phone communication
♦S-YXG50 is music synthesizer software to playback MIDI
files on the system
Dimensions
♦Micro-ATX form factor (24.4cm x 19cm)
1: Introduction
5
Package Contents
Your mainboard package ships with the following items:
qThe mainboard
qThis User’s Guide
q1 UDMA/66 IDE cable
qFloppy disk drive cable
qSupport software on CD-ROM disk
q10/100BaseTX Ethernet LAN ( Only for MS7308E M/B )
Optional Accessories
You can purchase the following optional accessories for this
mainboard.
qExtended USB module
MS7308D/EMainboard User’s Manual
6
qStatic Electricity Precautions
Components on this mainboard can be damaged by static
electricity. Take the following precautions when unpacking the
mainboard and installing it in a system.
1. Keep the mainboard and other components in their original
static-proof packaging until you are ready to install them.
2. During installation, wear a grounded wrist strap if possible. If
you don’t have a wrist strap, discharge static electricity by
touching the bare metal of the system chassis.
3. Handle the mainboard carefully by the edges. Avoid touching
the components unless it is absolutely necessary. During
installation put the mainboard on top of the static-protection
packaging it came in with the component side facing up.
Pre-Installation Inspection
1. Inspect the mainboard for damage to the components and
connectors on the board.
2. If you suspect that the mainboard has been damaged, do not
connect power to the system. Contact your mainboard vendor
and report the damage.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Placa madre de MATSONIC
MATSONIC
MATSONIC MS6380SG Manual de usuario
MATSONIC
MATSONIC MS7380SG Manual de usuario
MATSONIC
MATSONIC MS7102C Manual de usuario
MATSONIC
MATSONIC MS7167D Manual de usuario
MATSONIC
MATSONIC MS9327E Series Manual de usuario
MATSONIC
MATSONIC MS7192SM Manual de usuario
MATSONIC
MATSONIC MS7191SM Manual de usuario
MATSONIC
MATSONIC MS9107C Manual de usuario
MATSONIC
MATSONIC MS7177CT Manual de usuario
MATSONIC
MATSONIC MS6383E Manual de usuario
MATSONIC
MATSONIC MS9147C Series Manual de usuario
MATSONIC
MATSONIC MS9118E Series Manual de usuario
MATSONIC
MATSONIC EM-5900V Manual de usuario
MATSONIC
MATSONIC MS9317E Series Manual de usuario
MATSONIC
MATSONIC MS8318E Series Manual de usuario
MATSONIC
MATSONIC MS9047C Series Manual de usuario
MATSONIC
MATSONIC MS6393E Manual de usuario
MATSONIC
MATSONIC MS7057C Manual de usuario
MATSONIC
MATSONIC MS8188E Series Manual de usuario
MATSONIC
MATSONIC MS7112C Manual de usuario
Manuales populares de Placa madre de otras marcas
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manual de usuario
Gigabyte
Gigabyte GA-9IVDT Manual de usuario
Texas Instruments
Texas Instruments ADS8372EVM Manual de usuario
Commell
Commell MS-C73 Manual de usuario
IBT Technologies
IBT Technologies MB860 Manual de usuario
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manual de usuario
