MATSONIC MS7102C Manual de usuario

Important Information

This publication, including all photographs, illustrations and software, is

Neither this manual, nor any of the material contained herein, may be

reproduced without the express written consent of the manufacturer.

Disclaimer

The information in this document is subject to change without notice. The

manufacturer makes no representations or warranties with respect to the

contents hereof and specifically disclaims any implied warranties of

merchantability or fitness for any particular purpose. Further, the

manufacturer reserves the right to revise this publication and to make

changes from time to time in the content hereof without obligation of the

manufacturer to notify any person of such revision or changes.

Trademark Recognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft

Corp.

MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered

trademarks of Intel Corporation.

VGA, OS/2, PS/2 are registered trademarks of International Business

Machines.

AMD, K5, K6 are registered trademarks of Advanced Micro Devices Inc.

Cyrix, M1 are registered trademarks of Cyrix Corporation.

Other product names used in this manual are the properties of their

respective owners and are acknowledged.

Version 3.0

Safety Compliance

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to

radio communications. However there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following

measures:

!Reorient or relocate the receiving antenna.

!Increase the separation between the equipment and the receiver.

!Connect the equipment onto an outlet on a circuit different from that

to which the receiver is connected.

!Consult the dealer or an experienced radio/TV technician for help.

Shielded interconnect cables and shielded AC power cable must be

employed with this equipment to insure compliance with the pertinent RF

emission limits governing this device. Changes or modifications not

expressly approved by the system’s manufacturer could void the user’s

authority to operate the equipment.

Declaration of Conformity

This device complies with part 15 of the FCC rules. Operation is subject

to the following conditions:

!This device may not cause harmful interference, and

!This device must accept any interference received, including

interference that may cause undesired operation.

Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian

Interference-causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du

Réglement sur le matériel brouilieur du Canada.

Contents

Chapter 1: Introduction

Welcome.......................................................................1

About the Manual..........................................................2

Checklist........................................................................2

Features........................................................................3

Chapter 2: Installation

Before You Begin..........................................................6

Mainboard Guide...........................................................7

I/O Ports Side View.......................................................8

Preparing the Mainboard...............................................9

Install the Mainboard in the System Case ....................17

Make the External Connections....................................22

Chapter 3: Setup

About the Setup Utility...................................................23

Standard CMOS Setup Option......................................25

BIOS Feature Setup Option..........................................26

Chipset Features Option...............................................29

Power Management Setup Option................................31

PNP/PCI Configuration Option......................................34

Load BIOS Defaults Option...........................................36

Load Setup Defaults Option .........................................36

Integrated Peripherals Option.......................................36

Supervisor and User Password Settings ......................39

IDE HDD Auto Detection Option...................................40

Save And Exit Setup Option .........................................40

Exit Without Saving Option ...........................................40

Chapter 4: Software

About the Software........................................................41

Running the Support CD-ROM .....................................43

Utility Folder Insatllation Note.......................................43

CMI8338 Audio Folder Installation Note.......................44

VIA Folder Installation Note ..........................................45

Mainboard Installation Notes ........................................47

Appendix 1: Quick Jumper Setting Reference..............48

Welcome

Congratulations on your purchase of the MS7102C mainboard. This

mainboard features the latest VIR ET82C693/596A chipset. This is a

very special mainboard which allows you to install almost any kind of

Intel Pentium-II/III processor. The MS7102C is a full-sized ATX board

measuring 305x220mm and using 4-layer printed circuit board.

The MS7102C has a special design feature so that it includes a Pentium-

II Slot-1 processor slot and a PPGA (Plastic Pin Grid Array) Celeron

Socket-PGA370 processor socket. This feature means that you can

install the mainboard with either a Pentium-III cartridge, a Pentium-

II cartridge, the SEPP (Single Edge Processor Package) Celeron

cartridge, or one of the new generation PPGA Celeron cartridges.

In addition, the mainboard supports a 66 MHz memory bus, or a 100

MHz memory bus, so you can use inexpensive 66MHz memory chips, or

higher-performance PC-100 memory chips. The board is installed with

an integrated PCI-3D sound system and has a full suite of I/O ports.

Seven expansion slots are available for system development and

hardware monitoring is supported.

This board allows complete flexibility. System integrators can choose the

high-performance Pentium-II processor cartridge or the inexpensive

PPGA Celeron processor according to the system requirements and the

price/performance comparison of the two kinds of processor.

This chapter contains the following information:

!About the Manual explains how the information in this manual is

organized

!Checklist comprises a list of the standard and optional components

that are shipped with this mainboard,

!Features highlights the functions and components that make this

one of the best value mainboards on the market

About the Manual

The manual consists of the following chapters:

Introduction

Use the Introduction Chapter to learn about the features of the

mainboard, and the checklist of items that are shipped with the package.

Installation

Use the Installation Chapter to learn how to install the mainboard and

get your system up and running.

Setup

Use the Setup Chapter to configure the mainboard for optimum

performance.

Software

Use the Software Chapter to learn how to use the software drivers and

support programs that are provided with this mainboard.

Checklist

Compare the contents of your mainboard package with the standard

checklist below. If any item is missing or appears damaged, please

contact the vendor of your mainboard package.

Standard Items

"1 x MS7102C Mainboard

"1 x Cable/Bracket Pack

Diskette drive ribbon cable

IDE drive ribbon cable

"This User’s Manual

"Software Support CD-ROM Disc

Optional Items

1 x V 9.0 Fax/Modem Card

Features

The key feature of this mainboard is the dual processor sockets which

allow you to install any of the Pentium-III and Pentium-II processors

including Slot1 cartridges SEPP Celerons and PPGA Celerons. In

addition, this is a full-sized ATX mainboard with a full set of expansion

slots for maximum development potential.

Support for Pentium-III/Pentium-II Cartridges or PPGA Celeron

The principal feature of this mainboard is that it can support three kinds

of processors: Pentium-III cartridges, Pentium-II cartridges and SEPP or

PPGA Celerons. Pentium-III cartridges feature 512K of level-2 cache

memory with improved instructions to handle 3D audio and video.

Speech recognition, MPEG2 motion picture encoding/decoding, and

TCP/IP internet connections. The Pentium-III runs over a 100 MHz

system bus and operate at clock speeds from 450 MHz up to 550 MHz

or more.

The Pentium-II cartridges are very powerful processors which include

32K of internal level-1 cache memory and 512K of external level-2 cache

memory. The first generation of Pentium-II cartridges ran over a 66 MHz

system bus, but current Pentium-II cartridges run over a 100 MHz

system bus and operate at clock speeds from 350 MHz up to 450 MHz

or more. The slot-1 processor can also be used by the SEPP Celeron

processors which can operate over a 66/100 MHz system bus and

operate at clock speeds up to 466 MHz.

The new generation PPGA Celeron processors ship in the familiar

square plastic package, and they install in a Zero Insertion Force (ZIF)

socket called a Socket-370. The new Celeron processors are close to

Pentium-II performance because they include a level-2 cache memory of

128K. However, they operate at a 66/100 MHz system bus and they

currently ship a clock speeds of 466 MHz.

System assemblers can install either a Pentium-III or Pentium-II

cartridge or the SEPP Celeron in the slot-1 processor slot. Alternatively,

they can install a second generation PPGA Celeron in the Socket-370

processor socket. Assemblers can choose the processor they need to

meet performance or price targets. You can configure the system for any

of the supported processor clock speeds using the BIOS setup utility. It

is not necessary to set switches or jumpers.

Choice of Memory Options

The board has three DIMM slots for the installation of 168-pin, 3.3V

standard or registered SDRAM (Synchronous Dynamic Random Access

Memory) memory modules. The system supports memory that has built-

in error correction (EC), error correction code (ECC), or has no error

correction.

If you are using a Pentium-III/PentiumII processor cartridge that operates

over a 100 MHz system bus, you must install PC-100 compliant memory

modules (memory that operates at 100 MHz). If you install the PPGA

Celeron processor, you can install memory that operates at 66 MHz (you

can install PC-100 memory if you wish, but the system will run the

memory at 66 MHz).

You can install one, two or three modules. Each memory module can

hold a maximum capacity of 128 MB of standard SDRAM chips, or 256

MB of registered SDRAM chips so maximum memory capacity is 384

MB of standard SDRAM memory or 768 MB registered SDRAM memory.

Highly Integrated Design

This board uses the VIR ET82C693/596A chipset. The ET82C693 forms

the north bridge and supports system buses of 66 and 100 MHz. It is

AGP Rev. 1 compliant and supports 3.3v AGP devices operating over a

66/133 MHz bus. The memory bus supports the fastest access (X-1-1-1)

for both 66 MHz and 100MHz operation. The board is compliant with PCI

Rev.2.1 operating at 33 MHz Four PCI Bus masters are supported.

The south bridge is provided by the 596A. This chip supports ACPI

(Advanced Configuration and Power Interface) Rev 1.0, onboard PCI

IDE channels, USB ports, and a System Management Bus for OS control

and configuration of devices.

Built-in PCI 3D Sound

The PCI Audio CMI 8738 is a single chip solution for PCI-bus 3D audio.

The chip provides Sound Blaster 16-bit-compatible audio, plus support

for Microsoft’s DirectSound 3D specification and Aureal A3D interface.

The sound ports include jacks for speakers, microphone and stereo in,

and a game/MIDI port. The audio system supports full duplex operation

and drivers are available for WIN 95/98 and WIN NT 4.0. The audio

system can output sound to 4 loudspeakers and also supports SPDIF

24-bit digital sound input and output.

Optional Built-in Communications

The mainboard has an integrated fax/modem connector. As an option,

you can purchase a fax/modem extension bracket which connects the

line and telephone RJII sockets to the board. The fax/modem supports

the V.90 protocol that allows transmissions at up to 56Kbps and is fully

compatible with earlier transmission and error correction standards. It

supports automatic fall back and caller ID.

Maximum Expansion Options

This is a full-sized ATX mainboard that offers the maximum in system

expansion. The board has a total of 7 expansion slots. The AGP slot can

be used by an AGP graphics adapter. The four 32-bit PCI slots can be

used by PCI expansion cards, and the two 8/16-bit ISA slots can be used

by legacy ISA expansion cards. One of the PCI slots is shared with one

of the ISA slots. This means that you can use either one of these slots

but not both at the same time. With six usable slots, this mainboard can

be installed with a full set of optional expansion cards.

Integrated I/O

Using the Winbond W83977EF-AW I/O chip and the Intel BX chipset, the

board has a comprehensive set of integrated I/O ports. The I/O port

array features PS/2 keyboard and mouse ports, a parallel port, two USB

ports, two serial ports, a monitor port, a game/MIDI port, and three audio

jacks. Optionally, you can use the built-in mainboard header to add in an

infrared port. The mainboard has two PCI-IDE channels and a floppy

disk drive interface.

Hardware Monitoring

The mainboard is installed with the GL520SM hardware monitoring chip.

Using this chip and the monitoring software supplied with the system,

users and system administrators can monitor critical parameters such as

the CPU temperature, the fan speeds and so on. Hardware monitoring

helps maintain the system and reduce maintenance costs and downtime.

Keyboard Power On Feature

Using the system BIOS setup program, you can configure the system to

turn on using a keyboard-typed password or hot key. A green keyboard

is not required.

Programmable Firmware

The mainboard includes Award BIOS that allows BIOS setting of CPU

parameters. The fully programmable firmware enhances the system

features and allows users to set power management, CPU and memory

timing, LAN and modem wake-up alarms, and so on. The firmware can

also be used to set parameters for different processor clock speeds so

that you don’t need to change mainboard jumpers and switches.

Before You Begin

Before you begin to install your MS7102C mainboard, take some

precautions to ensure that you avoid the possibility of damage to the

product from static electricity. Ensure too that you are installing the

mainboard into a suitable case.

Static Electricity

In adverse conditions, static electricity can accumulate and discharge

through the integrated circuits and silicon chips on this product. These

circuits and chips are sensitive and can be permanently damaged by

static discharge.

♦If possible wear a grounding wrist strap clipped to a safely

grounded device during the installation.

♦If you don’t have a wrist strap, discharge any static by touching

the metal case of a safely grounded device before beginning the

installation.

♦Leave all components inside their static-proof bags until they are

required for the installation procedure.

♦Handle all circuit boards and electronic components carefully.

Hold boards by the edges only. Do not flex or stress circuit

boards.

Choosing a Case

The MS7102C mainboard complies with the specifications for a full-sized

ATX board. Make sure that your system case supports a full-size ATX

board and has a power supply unit for all the expansion potential of the

system.

Some features on the mainboard are implemented by cabling connectors

on the mainboard to indicators and switches on the system case. Ensure

that your case supports all the features required. The MS7102C

mainboard can support one or two floppy diskette drives and four

enhanced IDE drives. Ensure that your case has sufficient power and

space for all the drives that you intend to install.

The mainboard has a set of I/O ports on the rear edge. Ensure that your

case has an I/O template that supports the I/O ports and expansion slots.

Mainboard Guide

Use the following illustration and key to identify the components on your

mainboard.

JP2 ATX1 JP4 DIMM1 DIMM2

DIMM3

CD1

SPDIF1

CD2

SIR1

FDD1

IDE2

IDE1

CASEFAN1

JP1

LED1

PANEL

WOM1

WOL1

SOCKET

PGA370

SLOT1

AGP1

PCI1

PCI2

PCI3 PCI4

ISA1

ISA2

SIDEBAND1

CPUFAN1

Tabla de contenidos

Otros manuales de Placa madre de MATSONIC

MATSONIC

MATSONIC MS7192S Manual de usuario

MATSONIC

MATSONIC MS7177CT Manual de usuario

MATSONIC

MATSONIC EM-5900V Manual de usuario

MATSONIC

MATSONIC MS9047C Series Manual de usuario

MATSONIC

MATSONIC MS7191SM Manual de usuario

MATSONIC

MATSONIC MS7122A Manual de usuario

MATSONIC

MATSONIC MS7012D Manual de usuario

MATSONIC

MATSONIC MS7057CT Manual de usuario

MATSONIC

MATSONIC MS9158 Series Manual de usuario

MATSONIC

MATSONIC MS6393E Manual de usuario

MATSONIC

MATSONIC MS8188E Series Manual de usuario

MATSONIC

MATSONIC MS8177C Series Manual de usuario

MATSONIC

MATSONIC MS7080SG Manual de usuario

MATSONIC

MATSONIC MS6391E Manual de usuario

MATSONIC

MATSONIC MS8308E Manual de usuario

MATSONIC

MATSONIC MS9077C Manual de usuario

MATSONIC

MATSONIC MS8157E Manual de usuario

MATSONIC

MATSONIC MS6261 Manual de usuario

MATSONIC

MATSONIC MS9138E Series Manual de usuario

MATSONIC

MATSONIC MS7188DSeries Manual de usuario

MATSONIC

MATSONIC MS7192SM Manual de usuario

MATSONIC

MATSONIC MS8318E Series Manual de usuario

MATSONIC

MATSONIC MS8328E Series Manual de usuario

MATSONIC

MATSONIC MS7117C Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario