MATSONIC MS-5120 Manual de usuario
MM
MMSS
SS--
--55
5511
1122
2200
00
MM
MMaa
aaiiii nn
nn bb
bb oo
oo aa
aa rr
rr dd
dd
MM
MM aa
aa nn
nn uu
uu aa
aa llll
Ver 1.0
Trademarks Acknowledgment
The information presented in this publication has been carefully reviewed;
however, no responsibility is assumed for any inaccuracy. Specifications
are subject to change without notice.
¥ IBM, AT, XT are trademarks of International Business Machines
Corporation.
¥ Award is a registered trademark of Award Software Inc.
¥ Intel, Pentium, and Triton are trademarks of Intel Corporation.
¥ MS-DOS and Microsoft are trademarks of Microsoft Corporation.
¥ Other trademarks belong to their respective owners.
ii
Table of Contents
Overview ............................................................................. 4
Main Features ..................................................................................5
Static Electricity Precautions...........................................................6
Unpacking the Mainboard ...............................................................7
Installation Procedures ........................................................ 8
Mainboard Layout ...........................................................................9
Jumper Settings..............................................................................10
Jumpers...................................................................................10
J2 Ð Power Supply Connector ................................................11
Connectors:.............................................................................11
USB1 Ð Universal Serial BUS Connector ..............................11
J1 Ð Keyboard Connector .......................................................11
J3 Ð HDD LED Connector .....................................................11
J7 Ð System Reset...................................................................11
JP2 Ð Flash ROM....................................................................11
JP6 Ð DIMM Module Voltage ................................................11
J8 Ð Power LED Connector ....................................................12
J4 Ð Speaker Connector ..........................................................12
JP1 Ð Clear CMOS .................................................................12
JP3A, B, C Ð CPU Speed Selectors ........................................12
JP11A, B Ð CPU Internal Clock Speed Selectors ..................12
JP8 Ð CPU Voltage Selectors .................................................12
JP10 Ð CPU Type Selectors....................................................13
PS/2 Mouse Connector...........................................................13
IR1 Ð Infra Red.......................................................................13
Memory Bank ................................................................................13
How to Identify Your BIOS.............................................. 14
How to Update and Flash Your BIOS ...........................................14
iii
Award BIOS Setup............................................................ 15
CMOS Setup Utility ......................................................................15
Standard CMOS Setup ..................................................................15
BIOS Features Setup......................................................................17
Chipset Features Setup ..................................................................20
Power Management Setup .............................................................21
PNP/PCI Configurations................................................................24
Load Setup Defaults ......................................................................25
Integrated Peripherals ....................................................................25
Supervisor/User Password.............................................................28
IDE HDD Auto Detection .............................................................28
Save and Exit Setup.......................................................................29
Exit without Saving .......................................................................29
Appendix: CPU Table ................................................... AÐ1
4
Chapter 1
OO
OOvv
vvee
eerr
rrvv
vviiii ee
ee ww
ww
Congratulations on your decision to purchase MS5120 Mainboard of the
MATSONIC series. This mainboard features the advanced capabilities of
the VIA PCI chipset with high speed PCI local BUS and super I/O and it
also provides the ultimate solution for optimizing the performance of your
system.
This highly flexible mainboard is designed to run a full line of Intel
Pentium, Cyrix/IBM 6x86, and AMD-K5 processors, and can be easily
upgraded due to its 321-pin ZIF socket and auto switch Split Voltage
Regulator. The processor performance is enhanced by a second level write-
back pipeline Burst SRAM cache of up to 512k and main memory of up to
384MB DRAM. Main memory can be installed by using the board's four
72-pin SIMM sockets and two 168-pin DIMM sockets, which accept high
performing SDRAM.
The MS5120 supports three 16-bit ISA slots and four 32-bit PCI slots. Also,
it features built-in high-speed super I/O onboard, including one USB
connector, two 16550A UART compatible Serial ports, one EPP/ECP
capable parallel port and IR which are integrated into a single dual-height
rear I/O panel for optimum ease of configuration. Moreover, a high-speed
PCI Bus Master Enhanced IDE controller is included to provide high-speed
connections for up to four IDE devices, including Hard Disk and CD-ROM
drives, and an upgradable Plug and Play Flash BIOS, and 16.6M PIO4
transfer rate.
Overview
5
Main Features
The MS5120 Mainboard comes with the following high-performance
features:
❑VIA PCIsetª chipset;
❑Flexible Processor Support;
Ñ Onboard 321-pin ZIF socket supports Intel Pentium
(P54C/P55C/MMX) CPU 75 ~ 233 MHz processors
Ñ Cyrix/IBM 6x86-P120+(100MHz) ~ 6x86-P200+(150 MHz)
processors/M2 series processors
Ñ AMD K5/K6 series processors;
❑Support switch Split Voltage Regulator;
❑Ultra-fast Level II Cache
Supports onboard Pipeline Burst SRAM expandable to 512K
Ñ Accepts up to 256MB RAM in two banks using four SIMMs of 8,
16, 32, 64 MB with support for FPM and EDO DRAM and two
DIMMs of 8, 16, 32, 64MB with support for SDRAM and EDO
DRAM;
❑Three 16-bit ISA and four 32-bit PCI expansion slots provide Master
Mode;
❑System BIOS supports 4 IDE hard disk drives, the capacity of each
hard disk can surpass 528MB up to 8GB;
❑Universal Serial BUS (USB) Support
Two Universal Serial Bus plug-in connectors integrated on the rear I/O
panel;
MS5120 Mainboard Manual
6
❑Supports Ultra DMA/33
❑Enhanced PCI Bus Master IDE Controller
Integrated Enhanced PCI local bus IDE controller with two connectors
supports up to four IDE devices such as Hard Disk, CD-ROM or tape
backup drives via two channels for high-speed data throughput. This
controller supports PIO Modes 3 and 4, DMA Mode 2, and Ultra
DMA/33 for optimized system performance;
❑Super Multi I/O
Includes two integrated 16550A UART compatible serial ports, one
EPP/ECP capable parallel port, one IR port, and one Floppy Drive
connector;
❑Award BIOS
System BIOS supports NCR810 SCSI BIOS firmware and Green
feature function, Plug & Play Flash ROM ready.
Static Electricity Precautions
Static electricity can easily damage your MS-5120 Mainboard. The
following procedures can help you to protect your mainboard from
electrostatic discharge.
1. Keep the mainboard and other system components in anti-static
packaging until you are ready to install them.
2. Ground yourself before removing any system component from its
protective anti-static packaging. Examples of grounded surfaces within
easy reach are expansion slots at the rear of the system case and any
other unpainted metallic surface on the system chassis.
3. Frequently ground yourself to discharge static electricity that may build
up in your body while installing and /or configuring your system.
Avoid touching sensitive components. Only handle the mainboard by
its edges or by the mounting bracket.
Overview
7
Unpacking the Mainboard
The MS-5120 Mainboard comes in a sturdy cardboard shipping carton. The
carton contains the following items:
¥ MS-5120 Mainboard
¥ IDE, FDD, Serial port and Printer cables
¥ This UserÕs Manual
The MS-5120 Mainboard is easily damaged by static electricity. Observe
the following precautions while unpacking and installing the mainboard.
Caution: Touch an unpainted area of the system chassis before
handling the mainboard or any component. Doing so will
discharge the static charge your body may have built.
Do not apply power if the mainboard appears damaged. If
there is damage to the board, or missing items, contact your
dealer immediately.
8
Chapter 2
II
IInn
nnss
sstt
ttaa
aallll llll aa
aa tttt iiii oo
oo nn
nn PP
PP rr
rr oo
oo cc
cc ee
ee dd
dd uu
uu rr
rr ee
ee ss
ss
This chapter explains how to configure the MS5120 Mainboard's hardware.
Before doing any installation, make sure that you are working with an
unplugged mainboard. Many components powered by low voltage current,
but there still may be a dangerous electric current coming from the leads
and power supply.
To set up your computer, you should follow these installation steps:
❑Step 1 Ñ Set system jumpers
❑Step 2 Ñ Install System RAM modules
❑Step 3 Ñ Install the CPU
❑Step 4 Ñ Install expansion cards
❑Step 5 Ñ Connect cables and power supply
❑Step 6 Ñ Set up BIOS feature (Please read Chapter Three.)
Installation Procedures
9
Mainboard Layout
SIMM1SIMM2SIMM3SIMM4
SL3 SL2 SL1
PCI4 PCI3 PCI2 PCI1
IDE2 IDE1
DIMM2 DIMM1
COM1 COM2
VIA
UM8670F
CacheCache
VIAVIA
Socket 7
PS1
VIA
J2
BIOS
PRN1
2
1
RST
HD-LED
TB-LED
TB-SW
AB
JP6
5V
3.3V
1
1
3
JP3
CBA
J1
IR1 USB1
1
JP2
3
1
JP1
1
A
B
C
D
E
FDC1
12
11
Keylock
1
Speaker
J8 J7 J4
J6 J3
J5
AB
JP10
1
AB
JP11
1
JP8
Figure 2-1 Mainboard Component Layout
MS5120 Mainboard Manual
10
Jumper Settings
Jumpers
You can configure hardware options by setting jumpers on the
motherboard. See figure 2-1 for jumper location. Some jumpers on the
board have three metal pins with each pin representing a different function.
To set a jumper, a black, white, or red cap containing metal contacts is
placed over the jumper pin(s) according to the required configuration. A
jumper is ÒshortedÓ when a cap has been placed on one or two of its pins.
NOTE : Users are not encouraged to change the jumper settings that are
not listed in this manual. Changing the jumper settings
improperly may adversely affect system performance.
P3 P2 P1
Pins 2 and 3 are shorted with a jumper cap
P3 P2 P1
Pins 1 and 2 are shorted with a jumper cap
The jumper is open
The jumper is shorted (closed)
Tabla de contenidos
Otros manuales de Placa madre de MATSONIC
MATSONIC
MATSONIC MS8308E Manual de usuario
MATSONIC
MATSONIC MS7127C Manual de usuario
MATSONIC
MATSONIC MS9027C Manual de usuario
MATSONIC
MATSONIC MS7101C Manual de usuario
MATSONIC
MATSONIC MS7132A Manual de usuario
MATSONIC
MATSONIC MS7380SG Manual de usuario
MATSONIC
MATSONIC MS9307C Series Manual de usuario
MATSONIC
MATSONIC MS6383E Manual de usuario
MATSONIC
MATSONIC MS9357E Series Manual de usuario
MATSONIC
MATSONIC MS7157C Manual de usuario
MATSONIC
MATSONIC MS7381SGM Manual de usuario
MATSONIC
MATSONIC MS9077C Manual de usuario
MATSONIC
MATSONIC MS6380SG Manual de usuario
MATSONIC
MATSONIC MS7308E Series Manual de usuario
MATSONIC
MATSONIC MS8147C Manual de usuario
MATSONIC
MATSONIC MS9017C Manual de usuario
MATSONIC
MATSONIC MS9317E Series Manual de usuario
MATSONIC
MATSONIC MS7167D Manual de usuario
MATSONIC
MATSONIC MS7057CT Manual de usuario
MATSONIC
MATSONIC MS9047C Series Manual de usuario
Manuales populares de Placa madre de otras marcas
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manual de usuario
Gigabyte
Gigabyte GA-9IVDT Manual de usuario
Texas Instruments
Texas Instruments ADS8372EVM Manual de usuario
Commell
Commell MS-C73 Manual de usuario
IBT Technologies
IBT Technologies MB860 Manual de usuario
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manual de usuario
