MATSONIC MS9027C Manual de usuario

Preface

This publication, including all photographs, illustrations and software, is protected un-

of the material contained herein, may be reproduced without written consent of the

author.

Version 1.0

Disclaimer

The information in this document is subject to change without notice. The manufactur-

er makes no representations or warranties with respect to the contents hereof and

specifically disclaims any implied warranties of merchantability or fitness for any par-

ticular purpose. The manufacturer reserves the right to revise this publication and to

make changes from time to time in the content hereof without obligation of the manu-

facturer to notify any person of such revision or changes.

Trademark Recognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.

MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel

Corporation.

Other product names used in this manual are the properties of their respective owners

and are acknowledged.

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not oc-

cur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

−Reorient or relocate the receiving antenna.

−Increase the separation between the equipment and the receiver.

−Connect the equipment onto an outlet on a circuit different from that to which

the receiver is connected.

−Consult the dealer or an experienced radio/TV technician for help.

MS9027C, V1.0

I845D/November 2001

Shielded interconnect cables and a shielded AC power cable must be employed with

this equipment to ensure compliance with the pertinent RF emission limits governing

this device. Changes or modifications not expressly approved by the system's manu-

facturer could void the user's authority to operate the equipment.

Declaration of Conformity

This device complies with part 15 of the FCC rules. Operation is subject to the follow-

ing conditions:

−This device may not cause harmful interference, and

−This device must accept any interference received, including interference

that may cause undesired operation.

Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian Interference-

causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement

sur le matériel brouilieur du Canada.

About the Manual

The manual consists of the following:

Chapter 1

Introducing the Mainboard Describes features of the mainboard,

and provides a shipping checklist.

Go to ⇒page 5

Chapter 2

Installing the Mainboard Describes installation of mainboard

components.

Go to ⇒page 10

Chapter 3

Using BIOS Provides information on using the BIOS

Setup Utility.

Go to ⇒page 27

Chapter 4

Using the Mainboard Software Describes the mainboard software.

Go to ⇒page 47

iii

Preface i

CHAPTER 1 5

Introducing the Mainboard 5

Introduction................................................................................................5

Checklist ....................................................................................................5

Standard Items .................................................................................................5

Features.....................................................................................................6

Choosing a Computer Case.......................................................................7

Mainboard Components.............................................................................8

CHAPTER 2 10

Installing the Mainboard 10

Safety Precautions...................................................................................10

Quick Guide.............................................................................................10

Installing the Mainboard in a Case...........................................................11

Checking Jumper Settings.......................................................................11

Setting Jumpers..............................................................................................11

Checking Jumper Settings..............................................................................12

Jumper Settings..............................................................................................12

Connecting Case Components ................................................................13

The Panel Connectors....................................................................................13

Installing Hardware ..................................................................................15

Installing the Processor..................................................................................15

Installing Memory Modules...........................................................................18

Installing a Hard Disk Drive/CD-ROM .........................................................19

Installing a Floppy Diskette Drive.................................................................20

Installing Add-on Cards.................................................................................21

Connecting Optional Devices ........................................................................22

Connecting I/O Devices ...........................................................................25

External Connector Color Coding..................................................................26

CHAPTER 3 27

Using BIOS 27

About the Setup Utility..............................................................................27

The Standard Configuration...........................................................................27

Entering the Setup Utility...............................................................................28

Updating the BIOS.........................................................................................28

Using BIOS..............................................................................................29

Standard CMOS Features...............................................................................30

Advanced BIOS Setup Option.......................................................................32

Advanced Chipset Features Option................................................................34

Integrated Peripherals Option ........................................................................36

Power Management Setup Option .................................................................39

PNP/PCI Configuration Option......................................................................42

PC Health Status Option................................................................................43

Frequency/Voltage Control ............................................................................44

Load Fail-Safe Defaults Option.....................................................................45

Load Optimized Defaults Option...................................................................45

Set Password Option......................................................................................45

Save & Exit Setup Option..............................................................................46

Exit Without Saving.......................................................................................46

CHAPTER 4 47

Using the Mainboard Software 47

About the Software CD-ROM...................................................................47

Drivers Installation....................................................................................47

Utility Software Reference........................................................................48

Introducing the Mainboard

Congratulations on purchasing the MS9027C mainboard. The MS9027C

mainboard is an ATX mainboard that uses a 4-layer printed circuit board and

measures 304.8 mm x 224 mm. The mainboard features a mPGA478 Socket

that accommodates Intel Pentium 4 processors supporting system speeds up

to 400 MHz and data bus bandwidths up to 3.2 GB/s.

The MS9027C incorporates the Intel i82845 (MCH) and the Intel 82801BA

(ICH2) chipsets, which supports 2.5V DDR DRAM, 2X/4X AGP (1.5V only),

and the AC’ 97 codec.

Compare the mainboard’s package contents with the following checklist:

Standard Items

•One mainboard

•One diskette drive ribbon cable

•One IDE drive ribbon cable

•Retention Module Clamp

•Software support CD

•This user’s manual

Processor The MS9027C mainboard uses a mPGA478 Socket that has

the following features:

•Accommodates Intel Pentium 4 478-pins CPU

•Supports a system bus (FSB) of 400 MHz

•Supports 3.2 GB/s data bus bandwidth

Chipset Intel’s innovative i82845 (MCH) and 82801BA (ICH2) chipsets

are based on an innovative and scalable architecture with

proven reliability and performance. A few of the advanced

features of the chipsets are:

•Host interface controller supports 400 MHz frontside

(system) bus frequency

•Supports 266 MHz DDR SDRAM devices.

•Supports a max of 2 Double-Sided DIMMs (4 rows popu-

lated) with unbuffered DDR266 (w/ or w/out ECC).

•Supports a maximum memory bandwidth of 2.1 GB/s with

DDR266.

•AGP controller is AGP 2.0 compliant and supports 2x/4x

Fast Write Protocol (1.5V only)

•PCI IDE controller supports PCI bus mastering, PIO

modes 0~4, and UDMA 33/66/100

•Two USB controllers double the bandwidth to 24 Mbps

across four ports

•Integrated AC’ 97 audio that supports full surround sound

with up to six channels

Additional key features include support for an AC 97 link for audio

and modem, hardware monitoring, and ACPI/OnNow power man-

agement.

Memory The mainboard can accommodate 2.5V DDR SDRAM. It ac-

commodates two unbuffered 2.5V 184 pin slots with a total

maximum capacity of 2 GB.

VGA The MS9027C includes a 4xAGP slot that provides four times the

bandwidth of the original AGP specification. AGP technology

provides a direct connection between the graphics sub-system

and the processor so that the graphics do not have to compete for

processor time with other devices on the PCI bus.

AC’ 97 Audio

Codec The AC’ 97 Audio codec is compliant with the AC’ 97 2.2

specification, and supports 18-bit ADC (Analog Digital Con-

verter) and DAC (Digital Analog Converter) resolution as well

as 18-bit stereo full-duplex codec with independent and vari-

able sampling rates.

Expansion

Options The mainboard comes with the following expansion options:

•Six 32-bit PCI slots

•One 4xAGP slot (support 1.5V only)

•One Communications Network Riser (CNR) slot

•Two IDE connectors which support four IDE channels and

a floppy disk drive interface

The MS9027C supports Ultra DMA bus mastering with transfer

rates of 33/66/100 MB/sec.

Integrated I/O The mainboard has a full set of I/O ports and connectors:

•Two PS/2 ports for mouse and keyboard

•Two serial ports

•One parallel port

•One MIDI/game port

•Two USB ports

•Audio jacks for microphone, line-in and line-out

BIOS

Firmware This mainboard uses Award BIOS that enables users to con-

figure many system features including the following:

•Power management

•Wake-up alarms

•CPU parameters and memory timing

•CPU and memory timing

The firmware can also be used to set parameters for different

processor clock speeds.

There are many types of computer cases on the market. The mainboard com-

plies with the specifications for the ATX system case. Some features on the

mainboard are implemented by cabling connectors on the mainboard to indi-

cators and switches on the system case. Ensure that your case supports all

the features required. The mainboard can support one or two floppy diskette

drives and four enhanced IDE drives. Ensure that your case has sufficient

power and space for all the drives that you intend to install.

Most cases have a choice of I/O templates in the rear panel. Make sure that

the I/O template in the case matches the I/O ports installed on the rear edge

of the mainboard.

This mainboard has an ATX form factor of 304.8 mm x 224 mm. Choose a

case that accommodates this form factor.

Table of Mainboard Components

Label Component

AGP1 Accelerated Graphics Port

ATX1 Standard 20-pin ATX power connector

AUDIO1 Mic/SpeakerOut header

BAT1 Three volt realtime clock battery

CASFAN1 Case Fan

CDIN1 CD-in connector (Panasonic)

CDIN2 CD-in connector (Sony)

CPUFAN1 Cooling fan for CPU

CNR1 Communications Networking Riser slot

CPU Socket CPU socket (mPGA478)

DIMM1 ~ DIMM2 Two 184-pin DDR sockets

FDD1 Floppy disk drive connector

IDE 1 Primary IDE channel

IDE 2 Secondary IDE channel

J1 External SMI connector

J2 Smart I/O connector

JP1 Clear CMOS jumper

JP2 BIOS protect jumper

LED1 LED status indicator connector

LAUDIO1 Mic/SpeakerOut connector

LSJ1 Single color LED header (comply with OEM specs. only)

LUSB1 USB connector 2

LPANEL1 Panel connector for case switches and LEDs

PANEL1 Front panel connectors for case switches and LEDs

PCI1 ~ PCI6 Six 32-bit add-on card slots

PWRFAN1 Power fan connector

SIR1 Serial IR port

SPEAKER1 Speaker connector

SJ1 Single color LED header

USB1 Front panel USB headers

WOL1 Wake On LAN wakeup connector

WOM1 Wake On Modem wakeup connector

Note: LED1 is usually connected to a light that indicates that the computer is

powered on. Do not install hardware or disconnect power cables while the

LED is on.

This concludes Chapter 1. The next chapter explains how to install the main-

board.

Installing the Mainboard

Follow these safety precautions when installing the mainboard:

•Wear a grounding strap attached to a grounded device to avoid

damage from static electricity.

•Discharge static electricity by touching the metal case of a safely

grounded object before working on the mainboard.

•Leave components in the static-proof bags they came in.

•Hold all circuit boards by the edges. Do not bend circuit boards.

This Quick Guide suggests the steps you can take to assemble your system

with the mainboards.

The following table provides a reference for installing specific components:

Locating Mainboard Components Go to page 8

Installing the Mainboard in a Case Go to page 11

Setting Jumpers Go to page 11

Installing Case Components Go to page 13

Installing the CPU Go to page 15

Installing Memory Go to page 18

Installing a HDD and CD-ROM Drive Go to page 19

Installing a FDD Go to page 20

Installing Add-on Cards Go to page 21

Connecting Options Go to page 22

Connecting Peripheral (I/O) Devices Go to page 25

Tabla de contenidos

Otros manuales de Placa madre de MATSONIC

MATSONIC

MATSONIC MS8147C Manual de usuario

MATSONIC

MATSONIC MS7192S Manual de usuario

MATSONIC

MATSONIC MS6261 Manual de usuario

MATSONIC

MATSONIC MS6380SG Manual de usuario

MATSONIC

MATSONIC MS7122A Manual de usuario

MATSONIC

MATSONIC MS7117C Manual de usuario

MATSONIC

MATSONIC MS9138E Series Manual de usuario

MATSONIC

MATSONIC MS9147C Series Manual de usuario

MATSONIC

MATSONIC MS9047C Series Manual de usuario

MATSONIC

MATSONIC MS7192SM Manual de usuario

MATSONIC

MATSONIC MS9017C Manual de usuario

MATSONIC

MATSONIC MS7380SG Manual de usuario

MATSONIC

MATSONIC MS7381SGM Manual de usuario

MATSONIC

MATSONIC MS9138D Series Manual de usuario

MATSONIC

MATSONIC MS7057CT Manual de usuario

MATSONIC

MATSONIC MS-5120 Manual de usuario

MATSONIC

MATSONIC MS9118E Series Manual de usuario

MATSONIC

MATSONIC MS7188DSeries Manual de usuario

MATSONIC

MATSONIC MS7191SM Manual de usuario

MATSONIC

MATSONIC MS8318E Series Manual de usuario

MATSONIC

MATSONIC MS9307C Series Manual de usuario

MATSONIC

MATSONIC MS7057C Manual de usuario

MATSONIC

MATSONIC MS9158 Series Manual de usuario

MATSONIC

MATSONIC MS7023D Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario