Mastech MS6460 Manual de usuario

MS6460

Laser Distance Meter

User's Manual

01 02

Safety Regulations

Please read carefully safety regulations

and guidance before initial use.

Before using the meter, please read

all instructions and safety regulations in

this manual carefully. It may result in

meter damage, affecting the

measurement accuracy, body injury to

the user or others without following the

operation methods in this manual.

Do not open or repair the meter by

yourself in any way. Do not retrofit

illegally or change meter laser

transmitter performance. Please keep

the meter properly, do not place it in

places where children may touch, avoid

being used by unrelated persons.

Electromagnetic radiation of the

meter may interfere with others

equipments and devices. Do not use it

nearby aircraft or medical equipment.

Do not use it under flammable and

explosive environment.

Don't make the meter's laser device

radiate eyes or other body parts of you

or others. Don't make the laser device

radiate high reflective object surface.

If the meter has any quality issue,

or you have any doubt on the meter,

please contact your local dealer or

Sndway factory, we will solve for you

as soon as possible.

03 04

Install battery, display and

keyboard Install and replace

• Open battery door at the back of the

meter, put into battery in accordance

with correct polarity of the meter, then

close the battery door.

• Only 1.5V AAA alkaline battery can be

used for the meter.

• When the meter is not used for a long

time, please remove the battery to

avoid the battery corroding the

meter's main engine.

battery Backlight

indication

Auxiliary

display area

Measurement

unit indication

Display

Laser transmitting

Measuring basis

Maximum indication

Indication for area,

volume, Pythagorean

theorem and indirect

measurement

Minimum indication

Main display area

Battery power indication

Store data, view stored data

Key

Menu key

“ - ” key

Pythagorean indirect

measurement key

Storage,

read storage key

Turn-on and

measurement key

“ + ” key

Area and volume key

Measuring base

selection key

Turn-off and

clear key

05 06

Turn on meter, menu setting

Turn on and off meter

In the Off mode, press key, the meter

and laser will start at the same time, the

meter enters test mode.

In the On mode, long press key for

3 seconds to turn off the meter. The

meter will automatically turn off if there

is no any operation within 150 seconds.

Unit setting

Press key, MENU and MENU→UNIT

will display on the screen. There are

four units for choice from UNIT.

key can be used for MENU→UNIT mode.

Under the MENU, long press key to

save current setting and quit setting

state. Or press key to quit setting

state. The following units can be chose

on the meter:

Length Area

0.000m

0.00m

0.0in

0.00ft

0.000m2

0.00m2

0.00ft2

Volume

0.000m3

0.00m3

0.00ft3

Backlight setting

Press key, MENU→UNIT will display

on the screen, press key again,

ON/OFF will display on the main display

area of the screen, key can be

used for turning on/off the backlight,

long press key to save and quit

current setting, press to quit the

setting mode. Backlight is on by default.

07 08

Measuring basis setting

Press key to exchange front basis

and end basis, it is end basis by default.

Distance measurement, area,

volume, Pythagorean indirect

measurement, add/subtract

function

Single measurement:

In the Test mode, press key to

radiate laser, lock measurement point.

Press key again for single distance

data measurement, measurement result

will display in the main display area.

Continuous measurement:

In the Test mode, long press key to

enter the continuous measurement

state, the maximum measurement value

and the minimum measurement value

will display on the screen during the

continuous measurement. Current

measurement value will display in the

main display area, short press key

to quit the continuous measurement

mode.

Area measurement:

Press key, will display on the

screen, one edge of rectangular is

flashing, complete the following

operations according to prompts: Press

key to measure the first edge

(Length) Press key to measure the

second edge (Width) The meter will

automatically make area calculation,

the result will display in the main

display area.

09 10

Press key to clear the previous

result, measure it again

Area measurement:

Press key, will display on the

screen, one edge of cube is flashing,

complete the following operations

according to prompts

Press key to

measure the first edge (Length) Press

key to measure the second edge

(Width)

Press key to measure the third edge

(Height) The meter will automatically

make volume calculation, the result will

display in the main display area.

Press key to clear the previous

result, measure it again

Indirect measurement with

Pythagorean theorem

In the meter, there are three default

modes to measure single distance of

triangle with Pythagorean theorem.

Users can make indirect measurements

easily in specific complex environment.

can be used for mode selection:

1) Press key. On the screen:

hypotenuse is flashing

Press key, measure the length

of the hypotenuse with dotted line

according to prompts on the screen

(a)

Press key to measure the length

of the leg with dotted line (b)

The meter will automatically calculate

the length of the leg with solid line (x)

11 12

2) Press key twice. On the screen:

erect side is flashing.

Press key, measure the length of

one of legs with dotted line according

to prompts on the screen (a)

Press key to measure the length

of another leg with dotted line (b)

The meter will automatically calculate

the length of the hypotenuse with

solid line (x)

3) Press three times. On the screen:

hypotenuse is flashing

Press key, measure the length of

one of hypotenuses with dotted line

according to prompts on the screen

(a)

Press key to measure the length of

the hypotenuse with dotted line in the

figure (b)

Press key to measure the length of

another hypotenuse with dotted line in

the figure (c) The meter will automatically

work out the length of the leg with solid

line (x)

In the Pythagorean measurement mode,

leg length should be less than

hypotenuse length, the meter would

calculate, otherwise, the device will

show error signal prompt.

13 14

In the Pythagorean measurement mode,

to ensure measurement accuracy, it

should ensure to measure from the

same starting point, and measure in

hypotenuse, leg order.

Add/subtract measurement

function:

Cumulative or inverse cumulative

operation can be done for single

distance measurement with add/subtract

operation.

Press key, “+” will display in the main

display area, enter the cumulative

measurement mode. Accumulated value

of the last measurement value and the

current measurement value will display

on the screen.

Press key, “-” will display in the main

display area, enter the inverse cumulative

measurement mode. Difference value of

the last measurement value and the

current measurement value will display

on the screen.

Browse recordings:

Short press key to search the stored

measurement data, use key or

key to move forward or backward for

browsing. Or long press to clear all

stored recordings.

Store and browse:

Store recordings

If the current data is valid in the

measurement mode, long press key

for 3 seconds, the current measurement

data will be automatically stored in the

meter memory. MS6460 can store 20

pcs at most.

15 16

Prompt messages:

In the course of using the meter, the

following messages may display in the

main display area

Message Cause Solutions

Err1 Too poor signal

Measure target

point with strong

reflectance capacity

Too strong signal

Too low battery

voltage

Err2

Measure target

point with poor

reflectance capacity

Replace battery

Err3

Out of operating

temperature range

Err4

Use the meter under

the specified

environment

Pythagorean

measurement

violation

Err5

Measure again, to

ensure that the

hypotenuse is

greater than the leg

Storage damage Please contact with

your dealer

Err6

Technical parameters

Item

Maximum

measurement distance

Distance

measurement accuracy

Continuous

measurement function

Measurement unit selection

Area measurement function

Volume measurement function

Pythagorean

measurement function

Add and subtract

measurement functions:

MS6460

60m/164ft

±2mm

Present

mm/in/ft

Present

Full mode

Present

Maximum/minimum value

Maximum storage

Key tone

Laser grade

Laser type

Automatic cutting laser

Automatic power-off

Present

20pcs

Present

635nm,<1mW

20S

150S

Backlight

17 18

Maximum battery life Single measurement

for 4000 times

Storage temperature range

Operating temperature range

Storage humidity

Battery

Weight (include battery)

Outside measurement

-20°C-60°C

0°C-40°C

RH85%

1.5V 3*AAA

160g

28*54*118mm

Note: In harsh environments, such as:

too strong sunshine, too large ambient

temperature fluctuation, weak reflection

effect of reflective surface, low battery,

measurement result would have large

error.

Daily maintenance of meter

• Do not place the meter in hot and

humid environment to store for long

time. If the meter is not used for long

time, please remove the battery and

place the meter into the included

meter case in a cool and dry place.

• Keep the meter surface clean. Use

soft damp cloth to wipe dust on the

surface. Don't use corrosive liquid to

clean the meter. Laser device window

and focus lens can be cleaned

according to the method for cleaning

optical device.

Otros manuales para MS6460

Tabla de contenidos

Otros manuales de Instrumento de medición de Mastech

Mastech

Mastech MS8340B Manual de usuario

Mastech

Mastech MS2015A Manual de usuario

Mastech

Mastech MS2301 Manual de usuario

Mastech

Mastech MS6503 Manual de usuario

Mastech

Mastech MS5308 Manual de usuario

Mastech

Mastech MS2000R Instrucciones de montaje

Mastech

Mastech MS2002 Instrucciones de montaje

Mastech

Mastech MS8221C Manual de usuario

Mastech

Mastech MS6252A Manual de usuario

Mastech

Mastech MS2205 Manual de usuario

Mastech

Mastech MS2115B Manual de usuario

Mastech

Mastech MS2128 Manual de usuario

Mastech

Mastech MS6503 Manual de usuario

Mastech

Mastech MS6701 Manual de usuario

Mastech

Mastech MS2026R Instrucciones de montaje

Mastech

Mastech MS6900 Manual de usuario

Mastech

Mastech MS2015B Manual de usuario

Mastech

Mastech MS2203 Manual de usuario

Mastech

Mastech MS8332C Manual de usuario

Mastech

Mastech MS8238G Manual de usuario

Mastech

Mastech MS2225A Manual de usuario

Mastech

Mastech MS2115A Manual de usuario

Mastech

Mastech MS2201 Manual de usuario

Mastech

Mastech MS6252B Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario