Mastech MS2006B Manual de usuario

User’s Manual

CAT III

600 V

1. Safety information

The clamp leaker has been designed according to IEC

1010 -1 and IEC1010 - 2 - 032 concerning safety

requirements for electrical measuring instruments and

current clamps with double insulation overvoltage

category 600V CAT III and pollution 2.

2. Symbols

Note-Important safety information, refer to the

instruction manual.

Earth (ground) TERMINAL

Caution, possibility of electric shock

Application around and removal from UNINSULATED

HAZARDOUS LIVE conductors is permitted.

Alternating current

CAT III: MEASUREMENT CATEGORY III is applicable to

test and measuring circuits connected to the distribution

part of the building's low-voltage MAINS installation.

3. Description

This is a Clamp Leaker meter. Refer to the figure and to

the following steps to familiarize you with the clamp

leaker.

1. Transformer jaws

Pick up the AC current flowing through the conductor.

2. Hold Button

When this button is pushed, the display will keep the

last reading and “ ” symbol will

appear on the LCD until pushing it again.

3. Slip Key (select range)

The key is used to select measuring range.

4. Slip Key ( Power ON or OFF )

The key is used to turn the meter ”1” ( ON ) or “O” ( off ).

5. Display

3 1/2 digit, 7 segment, 13mm high, LCD.

6. Trigger

Press the lever to open the transformer jaws. When the

lever is released, the jaws will close again.

High Sensitivity

Ac Leakage Clamp Meter

High Sensitivity

Ac Leakage Clamp Meter

High Sensitivity

Ac Leakage Clamp Meter

LEAKAGE CLA MP ME TER

4. Operating instructions

AC Current measurement

• Set the Slip key of range at desired range position.

• Set the Slip key of power at “1” ( ON ) position.

• Press the trigger to open transformer jaw and to clamp

one conductor only, making sure that jaw is firmly

closed around the conductor.

• Read the measure result from the display.

5. Specifications

Accuracy is specified for a period of one year after

calibration and at 18°C to 28°C (64°F to 82°F) with

relative humidity to 75%.

GENERAL ACCURACY:

±% of reading number of least significant digits

DISPLAY: LCD, 1999 counts, updates 2 - 3/ sec.

OVERRANGE LNDICATION: “ 1 ” .

LOW BATTERY INDICATION: “ ”.

POWER: DC 2x 1.5V AAA Batteries

OPERATING ENVIRONMEMT: +5°C to +35°C

STORAGE TEMPERATURE: -10°C to +50°C

TEMPERATURE COEFFICIENT:

0.1×(Spec Acc’y) /°C 18°C or 28°C

JAW OPENING CAPABILITY: Φ31mm

DIMENSION: 176mm×59mm×28mm

WEIGHT: Approx. 150g

5. Technical Parameters

AC Current

±(2.0% of reading+10 digits)

Range Resolution Accuracy

2mA 0.001mA

0.01mA

0.1A

20mA

60A(<50A)

60A(>50A)

±(2.0% of reading+8 digits)

±(2.0% of reading+5 digits)

±(3.0% of reading+5 digits)

Frequency range: 50Hz / 60Hz.

Overload Protection:

120% ranges for 60 seconds max.

6. Replacing the battery

When the electrical tester displays the “ ”

mark, the battery must be replaced to avoid incorrect

measuring data. Use the following procedure to

replacing the battery:

1. The power key is used to select “O” ( OFF ).

2. Opening the battery cover by a piece coin.

3. Remove the exhausted battery and replace with

two new 1.5V AAA batteries.

4. Place battery cover and secure.

WARNING

To avoid electric shock, make sure that the test

leads have been clearly move away from the

circuit under measurement before opening the

battery cover of the meter.

WARNING

Do not mix old and new batteries. Do not mix

alkaline, standard (carbon-zinc), or rechargeable

(ni-cad, ni-mh, etc) batteries.

8. Accessories

Operator’s instruction manual

Battery 2 1.5V AAA

Gift box

00-05-1639

High Sensitivity

Ac Leakage Clamp Meter

High Sensitivity

Ac Leakage Clamp Meter

High Sensitivity

Ac Leakage Clamp Meter

Otros manuales de Instrumento de medición de Mastech

Mastech

Mastech MS5900 Manual de usuario

Mastech

Mastech MS6503 Manual de usuario

Mastech

Mastech MS2026R Instrucciones de montaje

Mastech

Mastech MS6508 Manual de usuario

Mastech

Mastech MS6580 Manual de usuario

Mastech

Mastech MS2009A Manual de usuario

Mastech

Mastech MS2301 Manual de usuario

Mastech

Mastech MS2108 Manual de usuario

Mastech

Mastech MS8238G Manual de usuario

Mastech

Mastech MS2016A Manual de usuario

Mastech

Mastech MS2015A Manual de usuario

Mastech

Mastech MS8240D Manual de usuario

Mastech

Mastech MS2009C Manual de usuario

Mastech

Mastech MS2001 Instrucciones de montaje

Mastech

Mastech MS2001 Instrucciones de montaje

Mastech

Mastech MS20006 Manual de usuario

Mastech

Mastech MS2203 Manual de usuario

Mastech

Mastech MS6701 Manual de usuario

Mastech

Mastech MS2030B Manual de usuario

Mastech

Mastech M266F Instrucciones de montaje

Mastech

Mastech MS2108 Manual de usuario

Mastech

Mastech MS2025A Manual de usuario

Mastech

Mastech MS6900 Manual de usuario

Mastech

Mastech MS2010A Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario