MARKLIFE P50 Manual de usuario
MARKLIFE
P50 LABEL PRINTER MANUAL
CONTENTS
Packing List
Introduction
Getting Started
Install and Setup Marklife APP
Create and Print your own label
Marklife APP Features
Trouble Shooting Guide
Print head/Rubber-covered roll cleaning
Warning
Notes
Warranty
01
02
05
08
12
20
21
23
24
25
26
01
02
03
04
05
06
07
08
09
10
11
PACKING LIST
MARKLIFE
P50 LABEL PRINTER MANUAL
Printer*1 Type C cable*1
Use Manual * 1
(includes instructions, warranties and certificate)
1
INTRODUCTION
2 3
Product Model: P50
Printing width: 20mm~50mm
Print accuracy: 203DPI
Bluetooth: 4.0
Battery capacity: 1200mAh
Charging time: less than 3 hours
Battery life: continuous printing length greater than 150 meters
Battery lifespan:charge and discharge times: more than 500 times
Printing life: more than 50km;
This label maker is only suitable for printing thermal label paper. For
better printing quality, it is recommended to use label paper from our
shop.
If the label maker is not used for a long time, in order to ensure the
battery life, it needs to be charged regularly.
The print head needs to be cleaned with alcohol cotton for a long time;
Note: Consumers shall use
the power adapter thathas
obtained China Compulsory
Certification andmeet the
standard requirements.
USB
On/off button
Basic parameters
4
On/Off button
Turn on P50 label maker: Press and hold the On/Off button until the
button green light appears.
Label calibration: Press the On/Off button twice in quick succession
the P50 label maker will come out with a label for label calibration.
Turn off P50 label maker: Press and hold the On/Off button until the
button light is off.
The P50 label maker power off automatically if you do not use it for
20 minutes.
Light status description
Green light: Fully charged / In normal use status.
Red light: Charging /Paper shortage/Overheat/Cover opening
Red light Flashing: Low Power, Low battery will cause unclear
printing, please charge it in time.
Orange light: Firmware is upgrading. Just wait till firmware
upgrading is finished and restart.
Blue light: Bluetooth is connected and in normal use status.
Blue light Flashing: Bluetooth is not connected.
GETTING STARTED
5
Step 1: Put in labels
1. Open the cover of the paper bin by holding the switch handles and
lifting the lid upwards.
2. Take out the spool and take off the movable plate. Load the paper
on the spool, put the movable plate back, and adjust its suitable size,
make sure the movable plate is fixed to avoid printing distortion.
3. Make sure the sticker side is facing down while Loading the paper,
Close the cover with some paper left outside of the cutter.
4. Turn on: Press and hold the On/Off button
until the button a green light appears.
67
INSTALL AND SETUP MARKLIFE APP
8
APP Download
Search“Marklife" in the App Store
For Apple phones, please search for "Marklife" in the Apple App Store
to download the APP.
For Android phones, please search "Marklife" in Google Play to get it.
9
APP Installation
To install and set up the Marklife APP, just follow the on-screen
instructions that step you through the setup process, including access
rights settings for support.
APP Bluetooth connectivity, custom label storage, and local custom
text printing function.
11
Connect P50 to APP
Turn on your label maker: Press and hold the On/Off button until the
button green light appears.
Turn on Bluetooth on your phone.
Open the Marklife APP.
Click Visitor Mode, our APP supports visitor mode, which means
you can use the app without registering. You can also register or
log in through a third-party account.
Click the "Unconnected" button, find your P50 label maker name,
and click to Connect it.
NOTE: Please make sure to connect the device from the app side. It
will be failed if you connect from the phone Bluetooth section.
10
CREATE AND PRINT YOUR OWN LABEL
12
Follow these steps to print out the labels you want:
Go to Create label>Select Label Type>Gap Label>Quick size
selection>Text, and edit your label content following the guidelines
below.
After you finish the content design, click Print>Check the preview
page>Print.
NOTE:
-Label calibration needs to be done each time the bin is opened
before printing, otherwise the label content will be printed off-set.
-Make sure to select the corresponding label paper type and size
before printing. Selecting an inappropriate paper type and size may
result in printing errors or wasted paper.
P50 Label Maker comes with a roll of Gap Label, size 40*30mm.
13
14 15
16
Double click "Double click Edit" to edit your text you can drag the text
box to adjust the text location. Choose the text size, font, and left and
right alignment, or directly drag the text box to complete the
adjustment of the text position. You can also add some stickers,
Graffiti, Dates, Lines, Shapes, and Numbers.P50 label machine also
supports printing pictures, Excel, Code, QR code, and OCR.
After finishing the text font settings, click Print to enter the print
preview page. On the print preview page, you can add the number of
copies to be printed at one time and the direction of printing, we
recommend the default print direction.
17
Tabla de contenidos
