MadgeTech TransiTemp-EC Hoja de especificaciones

TransiTemp-EC

In-Transit Temperature

Data Logger

PRODUCT

USER GUIDE

To view the full MadgeTech product line, visit

our website at madgetech.com.

TABLE OF CONTENTS

2Product Overview

2Installation Guide

2Device Operation

3Device Maintenance

4Need Help?

Product User Guide | 2

TransiTemp-EC

PRODUCT USER GUIDE

Product Overview

The TransiTemp-EC temperature data logger is designed

for high volume, low cost in-transit recording. It has

a custom molded case with a handle for convenient

attachment and comes in single and multi-use versions.

Installation Guide

Installing the Software

The Software can be downloaded from the MadgeTech

website at madgetech.com. Follow the instructions

provided in the Installation Wizard.

Installing the Docking Station

IFC203 (sold separately) — Follow the instructions

provided in the Installation Wizard to install the USB

Interface Drivers. Drivers can also be downloaded from the

MadgeTech website at madgetech.com.

Ordering Information

• 901749-00 — TransiTemp-EC

• 901752-00 — TransiTemp-EC-Multi

• 900313-00 — IFC203 Interface Cable

• 900036-00 — CR2032 Replacement Battery

Device Operation

Connecting and Starting the Data Logger

1. Once the software is installed and running, plug the

interface cable into the data logger.

2. Connect the USB end of the interface cable into an

open USB port on the computer.

3. The data logger will automatically appear under

Connected Devices within the software.

4. For most applications, select Custom Start from

the menu bar and choose the desired start method,

reading rate and other parameters appropriate for the

data logging application and click Start. (Quick Start

applies the most recent custom start options, Batch

Start is used for managing multiple loggers at once,

Real Time Start stores the dataset as it records while

connected to the logger.)

5. The status of the device will change to Running,

Waiting to Start or Waiting to Manual Start,

depending upon your start method.

6. Disconnect the data logger from the interface cable

and place it in the environment to measure.

Note: The device will stop recording data when the end of memory

is reached or the device is stopped. At this point the device cannot be

restarted until it has been re-armed by the computer.

Downloading Data from a Data Logger

1. Connect the data logger to the computer with the

interface cable.

2. Highlight the data logger in the Connected Devices

list. Click Stop on the menu bar.

3. Once the data logger is stopped, with the logger

highlighted, click Download.

4. Downloading will offload and save all the recorded

data to the PC.

Product User Guide | 3

TransiTemp-EC

PRODUCT USER GUIDE

Device Operation (cont’d)

Marking Feature

A date and time stamp may be placed in the recorded

data by holding the push button for 2 seconds to date and

time stamp data point while logging.

Alarm Settings

To change the settings for the alarm:

1. In the Connected Devices panel, select the intended

device to change the alarm settings.

2. On the Device tab, in the Information group, click

Properties. Users can also right-click on the device and

select Properties in the context menu.

3. A window will appear allowing to set the high and low

temperature alarms.

4. Press Change to edit the values.

5. Check Enable Alarm Settings to enable the feature

and check each high and low alarm box to activate it.

The values can be entered in the field manually or by

using the scroll bars.

6. Click Apply to write the settings to the device. To clear

an active alarm, press the Clear Alarm button.

LED Indicators

Green LED blinks every 10 seconds to

indicate safe conditions during logging

Red LED blinks every 10 seconds to

indicate alarm criteria have been exceeded

Device Maintenance

Battery Replacement on TransiTemp-EC-Multi

Materials: CR2032 Battery

1. Gently pry the two halves of the enclosure apart.-

Remove the circuit board.

2. Use a small non-metallic device to push the coin-cell

battery out of its holder.

3. Hold down the pushbutton in the middle of the circuit

board and insert the new battery into the holder.

4. Release the pushbutton and watch to verify that the

LEDs blink. (If they do not, then you may have inserted

the battery upside down. Remove the battery and

try again.)

5. Replace the circuit board in the enclosure.

6. Press the two halves of the enclosure back together.

Note: The TransiTemp-EC (Single Use) must be returned to the factory for

battery replacement.

Recalibration

The TransiTemp-EC and TransiTemp-EC-Multi cannot be

recalibrated.

TransiTemp-EC

NEED HELP?

DOC-1115036-00 | REV 1 2021.03.09

6 Warner Road, Warner, NH 03278

(603) 456-2011

info@madgetech.com

madgetech.com

Product Support & Troubleshooting

• Visit our Resource Library online at madgetech.com/resources.

• Contact our friendly Customer Support Team at (603) 456-2011 or support@madgetech.com.

MadgeTech 4 Software Support

• Refer to the built-in help section of the MadgeTech 4 Software.

• Download the MadgeTech 4 Software Manual at madgetech.com.

• Contact our friendly Customer Support Team at (603) 456-2011 or support@madgetech.com.

Este manual sirve para los siguientes modelos

Otros manuales de Registrador de datos de MadgeTech

MadgeTech

MadgeTech RTDTemp101A Manual de usuario

MadgeTech

MadgeTech HiTemp150FP-TSK Manual de usuario

MadgeTech

MadgeTech HiTemp140-FR Hoja de especificaciones

MadgeTech

MadgeTech Temp101A Manual de usuario

MadgeTech

MadgeTech Volt101A Manual de usuario

MadgeTech

MadgeTech UltraShock Series Manual de usuario

MadgeTech

MadgeTech HiTemp140-FPST-36 Manual de usuario

MadgeTech

MadgeTech RFCO2RHTemp2000A Hoja de especificaciones

MadgeTech

MadgeTech QuadTemp2000 Manual de usuario

MadgeTech

MadgeTech Volt101A Manual de usuario

MadgeTech

MadgeTech Level1000 Hoja de especificaciones

MadgeTech

MadgeTech RTDTemp2000 Manual de usuario

MadgeTech

MadgeTech Cryo-Temp Manual de usuario

MadgeTech

MadgeTech HITEMP140-1 Hoja de especificaciones

MadgeTech

MadgeTech Cryo-Temp Hoja de especificaciones

MadgeTech

MadgeTech MadgeNET RFTemp2000A Hoja de especificaciones

MadgeTech

MadgeTech Process101A 20mA Hoja de especificaciones

MadgeTech

MadgeTech Shock101-EB-5 Manual de usuario

MadgeTech

MadgeTech RHTemp101 Manual de usuario

MadgeTech

MadgeTech TSR101-EB Manual de usuario

MadgeTech

MadgeTech RTDTemp2000 Manual de usuario

MadgeTech

MadgeTech TSR101-5 Manual de usuario

MadgeTech

MadgeTech CurrentX Series Hoja de especificaciones

MadgeTech

MadgeTech LF101A Hoja de especificaciones

Manuales populares de Registrador de datos de otras marcas

TESTO

TESTO 176 Manual de usuario

HT Italia

HT Italia XL421 Manual de usuario

HBM

HBM SOMAT XR CX22B-R Manual de usuario

Agtrix

Agtrix 380i Manual de usuario

Hobo

Hobo H8 Pro Manual de usuario

Beijing ART Tech

Beijing ART Tech PCI2320 Manual de usuario

Athena

Athena GET SL1 Manual de usuario

Motec Systems

Motec Systems C185 Manual de usuario

Beijing ART Tech

Beijing ART Tech USB2832 Manual de usuario

Rotronic

Rotronic HygroLog HL20 Manual de usuario

MRC

MRC DW-6092 Manual de usuario

Racelogic

Racelogic VBOX LapTimer Manual de usuario

Edu-Logger

Edu-Logger 900-240 Manual de usuario

Elma

Elma DT173 Manual de usuario

Comet

Comet U0121M Manual de usuario

pico Technology

pico Technology PT-104 Manual de usuario

Soil Instruments

Soil Instruments GTecLink Manual de usuario

APLICOM

APLICOM A11 Manual de usuario