MacDon R113 Manual de usuario

R113/R116

Rotary Disc Pull-Type

Road-Friendly Transport™(MD #C2002) Installation

Instructions

214633 Revision C

Original Instruction

The harvesting specialists.

R1 Series Rotary Disc Pull-Type with Transport Installed

1014949

Published in August 2019.

The information in this publication is based on the information available and in effect at the time of printing. MacDon

Industries, Ltd. makes no representation or warranty of any kind, whether expressed or implied, with respect to the

information in this publication. MacDon Industries, Ltd. reserves the right to make changes at any time without notice.

Introduction

The Road-Friendly Transport™allows a MacDon R113/R116 Rotary Disc Pull-Type to stay within width restrictions for most

roads and highways while being towed.

This document explains how to install the transport onto the R113/R116 Rotary Disc Pull-Type. A list of parts included in

the kit is provided. Refer to 2 Parts List, page 5.

NOTE:

If installing this kit on a pull-type from model year 2019 or prior, order two washers (MD #18670) separately. These

washers are required to prevent damage to the slow moving vehicle (SMV) sign when reinstalling the sign.

NOTE:

If installing this kit on a pull-type from model year 2018 or prior, order one transport pin kit (MD #259258) separately. This

kit is required to install the hitch pin. On pull-types equipped with finger conditioners, this kit also adds clearance for the

center shield. Install the new finger conditioner center shield components before installing the Road-Friendly Transport™

kit. These Road-Friendly Transport™kit instructions explain when to install the hitch pin components provided in the

transport pin kit (MD #259258).

Installation time

The kit should take approximately 4 hours to install.

Conventions

The following conventions are followed in this document:

•Right and left are determined from the operator’s position, facing the direction of travel.

•Unless otherwise noted, use the standard torque values provided in the rotary disc pull-type operator’s manual or

technical manual.

NOTE:

Keep your MacDon publications up-to-date. The most current version can be downloaded from our website

(www.macdon.com) or from our Dealer-only site (https://portal.macdon.com) (login required).

This instruction is available in English and French and can be ordered from MacDon, downloaded from our Dealer Portal, or

from our International website (http://www.macdon.com/world).

214633 iRevision C

List of Revisions

At MacDon, we’re continuously making improvements, and occasionally these improvements affect product

documentation.The following list provides an account of major changes from the previous version of this document.

Section Summary of Change Internal Use Only

Throughout Updated references to rotary disc pull-types according to

product naming conventions.

Tech Pubs

Introduction, page i Revised statement:

•Unless otherwise noted, use the standard torque

values provided in the rotary disc pull-type operator’s

manual or technical manual.

ECN 57755 –added NOTE:

•If installing this kit on a pull-type from model year

2019 or prior, order two washers (MD #18670)

separately. These washers are required to prevent

damage to the slow moving vehicle (SMV) sign when

reinstalling the sign.

ECN 56953 and ECN 57017 –added NOTE:

•If installing this kit on a pull-type from model year

2018 or prior, order one transport pin kit

(MD #259258) separately. This kit is required to

install the hitch pin. On pull-types equipped with

finger conditioners, this kit also adds clearance for

the center shield. Install the new finger conditioner

center shield components before installing the Road-

Friendly Transport™kit. These Road-Friendly

Transport™kit instructions explain when to install the

hitch pin components provided in the transport pin

kit (MD #259258).

Tech Pubs

ECN 57755

ECN 56953

ECN 57017

Product Support

1.1 Signal Words, page 1 Added IMPORTANT and NOTE. Tech Pubs

2.1 Transport Assembly Parts List, page

Created separate topic for the transport assembly (small

parts bag not shown), and revised the parts lists as

follows:

•Added a footnote to clarify that three of the eleven

cable ties are attached to hoses MD #246366. The

remaining eight ties are included in the small

parts bag.

ECN 57834:

•Cover assembly (non-serviceable part) no longer

includes a module.

•Added one cap (MD #293127) for a total quantity

of one.

ECN 57593:

•Added one electrical cap (MD #134741) for a total

quantity of one.

ECN 57834

ECN 57593

214633 ii Revision C

Section Summary of Change Internal Use Only

•Added one electrical cap (MD #134742) for a total

quantity of one.

•Added one electrical harness (MD #281614) for a

total quantity of one.

2.2 Transport Assembly Parts List –

Small Parts Bag, page 8

Created a topic and parts list for the small parts bag

included with the transport assembly, and revised the

parts list as follows:

•Identified fitting MD #136149 as a separate part.

ECN 56030:

•Added footnote: Only used on a pull-type from model

year 2017 or prior.

ECN 57834:

•Added two screws (MD #136313) for a total quantity

of two.

•Added two nuts (MD #030855) for a total quantity

of two.

Added footnotes:

•MD #50101: Only four are used.

•MD #184657: Not used.

ECN 56030

ECN 57834

2.3 Remote Control Parts List, page 10 Added topic and parts list for the remote control and

harness.

Tech Pubs

3.1 Moving Hitch Swing Cylinder, page

•Step 1, page 13

Added step for model years 2018 and prior. ECN 56953

ECN 57017

Product Support

3.1 Moving Hitch Swing Cylinder, page

•See the NOTE below Step 6, page

Revised the NOTE to read “rod end”(previously was

“clevis end”):

•The rod end of cylinder will be attached to the

transport casting when the system is primed.

Product Support

3.2.1 Installing Latch Assembly, page

•Step 4, page 14

•Step 5, page 14

•Step 6, page 14

Added steps and associated pictures to show new

electrical caps.

ECN 57593

3.2.1 Installing Latch Assembly, page

•Step 7, page 14

•Step 8, page 14

•Step 9, page 14

•Step 11, page 15

•Step 12, page 15

Revised steps and/or associated pictures to show new

latch assembly hydraulics.

ECN 56030

214633 iii Revision C

Section Summary of Change Internal Use Only

3.2.1 Installing Latch Assembly, page

•Step 13, page 15

Added part numbers for clarity:

•MD #120333

•MD #18648

Tech Pubs

3.2.2 Installing Transport Assembly,

page 16

•Step 1, page 16

Revised step. Hardware is now discarded. Tech Pubs

3.2.2 Installing Transport Assembly,

page 16

•Step 3, page 16

Added part numbers for clarity:

•MD #136157

•MD #112130

•MD #136122

Tech Pubs

3.2.2 Installing Transport Assembly,

page 16

•Step 10, page 17

Added step for model years 2018 and prior. ECN 56953

ECN 57017

Product Support

3.2.2 Installing Transport Assembly,

page 16

•Figure 3.14, page 18

Updated picture to show new cover assembly that does

not include a module.

ECN 57834

3.2.2 Installing Transport Assembly,

page 16

•Step 13, page 18

•Step 14, page 18

Moved steps and associated picture from 3.2.4 Installing

Transport Valve, page 21 to this section because module

has to be removed and reinstalled.

ECN 57834

3.2.2 Installing Transport Assembly,

page 16

•Step 15, page 18

Added step and revised associated picture to show P-clip. ECN 57455

3.2.2 Installing Transport Assembly,

page 16

•Step 16, page 18

•Step 17, page 19

Added steps and associated pictures. ECN 57834

3.2.3 Installing Transport Wheels, page

Removed steps for relocating the axle on the right side of

the transport assembly.

Tech Pubs

3.2.5 Installing Transport Swing

Cylinder, page 22

•Step 2, page 22

Added part numbers for clarity:

•MD # 281101

•MD #18609

Tech Pubs

3.2.5 Installing Transport Swing

Cylinder, page 22

•Step 4, page 22

Revised step to identify dimension. Tech Pubs

3.2.5 Installing Transport Swing

Cylinder, page 22

•Step 5, page 23

Added part numbers for clarity:

•MD # 281101

•MD #18609

Tech Pubs

214633 iv Revision C

Section Summary of Change Internal Use Only

3.2.5 Installing Transport Swing

Cylinder, page 22

•Step 6, page 23

Revised the step to read “rod end”(previously was

“clevis end”). Added part numbers for clarity:

•MD # 281101

•MD #18609

Product Support

Tech Pubs

3.2.6 Installing Transport Alignment

Control, page 23

Removed a step regarding the cam assembly shipping

support that was only applicable to the factory-installed

transport option.

Tech Pubs

3.2.6 Installing Transport Alignment

Control, page 23

•Step 5, page 24

•Step 6, page 25

Revised steps and NOTE to clarify that the rod end of the

cylinder is being installed.

Product Support

3.2.6 Installing Transport Alignment

Control, page 23

•Step 9, page 26

Corrected part number to MD #247625. Was

MD #247598.

Tech Pubs

3.3.1 Installing Hydraulic Lines and

Hoses, page 27

Revised NOTE:

•Refer to the rotary disc pull-type operator’s manual

or technical manual for hydraulic fitting installation

details.

Tech Pubs

3.3.1 Installing Hydraulic Lines and

Hoses, page 27

•Step 1, page 27

Added picture to clarify step. Tech Pubs

3.3.1 Installing Hydraulic Lines and

Hoses, page 27

•Step 4, page 27

Added IMPORTANT. Tech Pubs

3.3.1 Installing Hydraulic Lines and

Hoses, page 27

•Step 5, page 27

Added part number of fitting for clarity. Tech Pubs

3.3.1 Installing Hydraulic Lines and

Hoses, page 27

•Step 10, page 28

•Step 11, page 28

•Added part number MD #247781 for clarity.

•Revised steps to correctly identify ports C and D.

Tech Pubs

3.3.1 Installing Hydraulic Lines and

Hoses, page 27

•Step 12, page 28

Added part number MD #30753 for clarity. Tech Pubs

3.3.1 Installing Hydraulic Lines and

Hoses, page 27

•Step 13, page 29

•Step 14, page 29

Added part number MD #246366 for clarity. Tech Pubs

3.3.1 Installing Hydraulic Lines and

Hoses, page 27

Added part number MD #30753 for clarity. Tech Pubs

214633 vRevision C

Section Summary of Change Internal Use Only

•Step 17, page 29

3.3.1 Installing Hydraulic Lines and

Hoses, page 27

•Step 35, page 32

Added part number MD #30753 for clarity. Tech Pubs

3.4.1 Installing Light Assemblies, page

•Step 3, page 33

Added step and revised associated picture. Tech Pubs

3.4.1 Installing Light Assemblies, page

•Step 4, page 33

Revised step to reference the correct bracket. Tech Pubs

3.4.1 Installing Light Assemblies, page

•Step 5, page 33

Revised step:

•Two nuts (MD #136431) and two bolts (MD #184667)

from the kit are used to install the light assembly.

Tech Pubs

3.4.1 Installing Light Assemblies, page

•Step 6, page 33

Added part number (MD #223185) for clarity. Tech Pubs

3.4.1 Installing Light Assemblies, page

•Step 7, page 33

Revised step to reference the correct bracket. Tech Pubs

3.4.1 Installing Light Assemblies, page

•Step 8, page 34

Added part numbers for clarity:

•MD #136178

•MD #50101

Tech Pubs

3.4.4 Connecting Selector Valve and

Transport Lighting Module, page 36

•Step 1, page 36

Added step and associated picture. ECN 57834

3.4.5 Installing Remote Control, page

•Figure 3.64, page 37

•Figure 3.66, page 38

Added picture and revised associated NOTE to identify

the fuse inside the remote control.

Tech Pubs

3.4.6 Installing Slow Moving Vehicle

Sign, page 39

•Step 2, page 39

Added “washers”and the NOTE to the step. ECN 57755

3.4.6 Installing Slow Moving Vehicle

Sign, page 39

•Step 3, page 39

Added part number MD #259218 for clarity. Tech Pubs

3.4.6 Installing Slow Moving Vehicle

Sign, page 39

•Step 4, page 39

Revised step as follows:

•Parts are retrieved from the shipping bag, not reused.

•Added part numbers MD #184667 and MD #136431

for clarity.

Tech Pubs

214633 vi Revision C

Section Summary of Change Internal Use Only

3.4.6 Installing Slow Moving Vehicle

Sign, page 39

•Step 5, page 39

Added “washers”to the step and revised associated

picture.

ECN 57755

3.4.6 Installing Slow Moving Vehicle

Sign, page 39

Removed the last two steps of this procedure because

the speed decal was already attached to the bracket.

Engineering

3.5 Installing Cover, page 40

•Step 1, page 40

Revised picture to clarify step. Tech Pubs

5.1 Preparing Rotary Disc Pull-Type for

Transport, page 47

Changed the following statement to a WARNING:

•To avoid bodily injury or death from unexpected

startup of machine, always stop engine and remove

key from ignition before leaving operator’s seat for

any reason.

Tech Pubs

5.1 Preparing Rotary Disc Pull-Type for

Transport, page 47

•Step 1, page 47

Added step. Tech Pubs

5.1 Preparing Rotary Disc Pull-Type for

Transport, page 47

•Step 2, page 47

Replaced steps for storing the hitch jack stand with a

reference section at the end of the manual.

Tech Pubs

5.1 Preparing Rotary Disc Pull-Type for

Transport, page 47

•Step 3, page 48

•Step 4, page 48

Flipped the order of these steps. Product Support

5.2 Transporting with a Tractor, page

Removed step for storing the jack stand because this is

completed in the previous section.

Tech Pubs

5.4 Converting from Field to Transport

Mode –With Road-Friendly

Transport

™

, page 51

Added DANGER:

•Stop the power take-off (PTO) before converting the

unit into transport mode. The cutting discs continue

to spin after the drive is turned off.

Changed the following WARNING to a CAUTION:

•To prevent equipment damage, ensure cutterbar

doors are properly closed before converting the

machine from field to transport mode.

Tech Pubs

5.5 Converting from Transport to Field

Mode –With Road-Friendly

Transport

™

, page 56

•Step 1, page 56

Added step.

Changed the following WARNING to a CAUTION:

•To prevent equipment damage, ensure cutterbar

doors are properly closed before converting the

machine from field to transport mode.

Tech Pubs

6.1 Attaching Rotary Disc Pull-Type to

the Tractor, page 61

Added “Attaching Hitch”reference chapters. Tech Pubs

214633 vii Revision C

Otros manuales para R113

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Maquinaria agrícola de MacDon

MacDon

MacDon A40-D Manual de usuario

MacDon

MacDon M Series Manual de usuario

MacDon

MacDon R113 Manual de usuario

MacDon

MacDon M150 Manual del propietario

MacDon

MacDon A30-D Manual de usuario

MacDon

MacDon R216 SP Manual de usuario

MacDon

MacDon R216 Manual de usuario

MacDon

MacDon M105 Manual de usuario

MacDon

MacDon R216 Manual de lista de piezas

MacDon

MacDon D60 Manual de usuario

MacDon

MacDon NEW HOLLAND D2 Series Manual de usuario

MacDon

MacDon M1170NT5 Manual de usuario

MacDon

MacDon 973 Manual de usuario

MacDon

MacDon R85 Manual de usuario

MacDon

MacDon R1 Series Manual de usuario

MacDon

MacDon M155 Manual de usuario

MacDon

MacDon FD75 Manual de usuario

MacDon

MacDon 5020 Manual de usuario

MacDon

MacDon NEW HOLLAND D2 Series Manual de usuario

MacDon

MacDon R85 Manual de usuario

MacDon

MacDon M Series Manual de usuario

MacDon

MacDon M150 Manual de usuario

MacDon

MacDon NEW HOLLAND D2 Series Manual de usuario

MacDon

MacDon FlexDraper FD2 Series Manual de usuario

Manuales populares de Maquinaria agrícola de otras marcas

GSi

GSi PNEG-2314 Manual de usuario

Checchi & Magli

Checchi & Magli TEXDRIVE Manual de usuario

Amazone

Amazone Cenius 4003-2TX Manual de usuario

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Manual de usuario

Cima

Cima BLITZ Instrucciones de funcionamiento y mantenimiento

Amazone

Amazone CombiDisc 3000 Instrucciones de instalación

HE-VA

HE-VA Disc-Roller XL Contour Manual de usuario

AGT

AGT AGT-SSFM Manual de usuario

Milestone

Milestone 72-84 Manual de usuario

KUHN

KUHN Hector 3000 Manual de usuario

Krone

Krone X-Disc 6200 Manual de usuario

Eliet

Eliet DZC450 Manual de usuario

Taarup

Taarup BIO+ B4000 Manual de usuario

Garland

Garland SHAKER 310 DPG Manual de usuario

stable comfort

stable comfort StableWall System Manual de usuario

Raven

Raven AccuBoom Manual de usuario

International

International 710 Manual de usuario

Ashland

Ashland HDW-3217-14 Manual de usuario